1 pcs. Roland Juno 106 Display Bezel blue newThis display bezel can replace the original display bezel on the Roland Juno-106. Due to the age of the Roland Juno-106 synthesiser, it is possible that the original bezel is scratched. It is also possible that the plastic has become brittle and must be replaced for this reason. Note on mounting the display bezel in the Roland Juno 106:It is best to use double-sided adhesive tape to stick the new display bezel in place. This adhesive tape can be purchased in suitable widths of e.g. 2 mm.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuitHosiden HLJ7001-01-3010This part is used inRoland JP-8000  Technical descriptionThe offered phone jack for PCB mounting is a Stereo jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. CR2016 forKorg M1 PCM CardRoland JD-800 PCM CardAttention: Shipping for Europe only Technical Description:The dimensions of CR2016 are diameter of 20 mm and a thickness of 1,6 mm. Manufacturer: Panasonic or Varta Information for handling old Battery's 

Digital-Analog-Converter for audio application for Roland E-PianosPCM61P - upgrade to PCM56PThis part is used from RolandRoland      part number:15209160   Resolution:                    18bitInterface:                      seriellConversion rate:            666kS/sNumber of DAC outputs: 2Number of channels:      1Case:                           DIP16warm-up time:               1 minMechanical Description:The digital to analog converter is housed in a DIP 16 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The DA converter has 2 x 8 connecting pins with grid of 2.54 mm x 7.62 mm.Technical Description:This D/A converter is a total compatible performance replacement to PCM56 DA Converter. The DA converter provides low distortion and typical differential linearity error is 0.001%. The interface is serial and provides a 18 bit resolution. The conversion rate is 666kS / s. For operation, no external components, such as temperature compensation or similar is required.It is a symmetrical supply voltage of +- 5V to +- 12V needed.  

1 pcs. double MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5048used by: KorgRolandYamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m

No longer available!Digital-Analog-Converter AK4396VF for audio application from AKM (Asahi Kasehi) - compatible with AK4393VF Resolution:                    24bitInterface:                      seriellCase:                           VSOP28Mechanical Description:The digital to analog converter is housed in a VSOP28 package and is designed for surface mounting on a circuit board. The D/A converter has 2 x 14 connecting pins with grid of 0.65 mm .Technical Description:This D/A converter was developed specifically for use in audio applications. The interface is serial and provides a 24 bit resolution.   

Hammer for Roland Progressive Hammer Action Keyboard- PHA2 and PHA3Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107e

NEW Replacement Keys, weighted for Roland SK8 Synthesizer Keyboardused inRoland XP-30Roalnd XP-80This are new Key's without "Red Glue-Problem" 

1 pcs. 16 pin FFC socket with 1.25 mm pitch16 pinPitch: 1.25 mmLength: 23,75 mmdeepth:  4,80 mmhight:      7,80 mmTechnical description

Keys, weighted for Roland SK9 KeyboardThis part fits for all Roland SK9 KeyboardsRoland SK9 Keyboard is used inFantom (FA76)Fantom G6, G7Fantom SFantom X6, X7XP-10Color/tint: pure white 

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 02Roland D-70, mainboard version 03We offer here a high quality replacement display with modern LED technology for the backlight.Color: white font/blue backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description! Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland D-70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", "02" or "03". 

11 pcs. Slide potentiometer with 20mm travel. Suitable forRoland TR-707Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements.The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 02Roland D-70, mainboard version 03We offer here a high quality replacement display with modern LED technology for the backlight.Color: black font/white backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description! Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland D-70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", "02" or "03". 

1 Stk. LCD display with LED backlightsuitable forRoland D-70, mainboard version 00Roland D-70, mainboard version 01We offer here a high quality replacement display with modern LED technology for the backlight.Color: black font/white backgroundScope of delivery:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description!Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", or "02". 

1 pcs. OLED Display brandnew in yellow forRoland D-550this is  a plug in ready Display replacement for Roland D-550. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation:We deliver this OLED dislpay for the Roland D-550 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Roland D-110 OLED Display NewReady to plug in OLED display for replacement in Roland D-110 . No soldering is required.Roland has built a display into the D-110  that is no longer available today. Above all, a mechanical adaptation to today's available OLED display is required.We have developed a mounting frame that allows the use of today's standard display. We have this frame specially manufactured.For the actual assembly of the new OLED display in the Roland D110 only a screwdriver is required.Scope of delivery of the OLED Display Set:OLED Display ready wiredMounting FrameInstructionsPlease choose you favorit color. Lifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 to 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. OLED Display brandnew in yellow forRoland JD-800this is  a plug in ready Display replacement for Roland JD-800. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Roland JD800 Encoder Board newThis Encoder PCB is suitable forRoland JD800Mechanical Description of Encoder Board:we deliver a brand new Encoder and a PCB ready mounted, herer you can just plug in the original cable. The cable is just pluged in and has to be taken over from original Encoder Board.This new Encoder has housing from Metall and a plastik axis.Practical advice for Mounting JD800 Encoder PCB:The circuit board must be machined:The new encoder has a larger thread than the original encoder in the JD-800. Furthermore, there is a pin on the encoder to prevent mechanical rotation of the component. The mounting hole for this pin must be re-drilled. The exact drilling plan can be seen in the pictures.The enlargement from 7 mm to 9 mm can be done by hand with a standard metal drill. This is gentler than working with a machine. 

1 pcs. Roland PG-1000 OLED Display Red NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. HEC470-01-630 DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland EP7 IIWe offer the original Hosiden power socket here.technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. White LCD Display with LED Backlight replacementRoland MV-30We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: Black Character  /  White BackgroundDelivery scope of LCD Display for MV-30:Display ready wiredInstruction for replacement Advantages of this LCD display compared to the original display from Roland:Modern LED technology for backlightVery good contrast ratioWe now have many years of experience with this type of LCD display. These displays are durable and robust.Notes on installation the Display in Roland MV-30 :To replace the display, the Roland MV-30 is opened from the back. So the rear of the case has to be removed. Afterwards  the Mainboard and Analog Board must be unscrewed. There are a lot of cables to be unpluged, but it is alle pluged in sockets. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Please do not forget to clean the Display Beezel in the housing.No soldering required.All you need is a screwdriver and side cutters.   

1 pcs. blue LCD Display with LED Backlight replacementRoland MV-30We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Blue BackgroundDelivery scope of LCD Display for MV-30:Display ready wiredInstruction for replacement Advantages of this LCD display compared to the original display from Roland:Modern LED technology for backlightVery good contrast ratioWe now have many years of experience with this type of LCD display. These displays are durable and robust.Notes on installation the Display in Roland MV-30 :To replace the display, the Roland MV-30 is opened from the back. So the rear of the case has to be removed. Afterwards  the Mainboard and Analog Board must be unscrewed. There are a lot of cables to be unpluged, but it is alle pluged in sockets. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Please do not forget to clean the Display Beezel in the housing.No soldering required.All you need is a screwdriver and side cutters.   

1 pcs. Roland JP8000 OLED Display brandnew in red this is  a plug in ready OLED Display replacement for Roland JP8000 Synthsizer. For this display replacement, we strongly recommend shortening the mounting bolts in the housing of the Roland JP8000. The OLED display itself is supplied pre-wired. No soldering is required Mounting instructions for Roland JP8000 OLED:The mechanical assembly of this OLED display is somewhat more complex. The synthesiser is opened from the back and almost all components have to be removed to access the display, unfortunately the keyboard also has to be removed.The display assembly:We have developed a special cable adapter for the display in the Roland JP8000. This makes it possible to continue using the flat cable used in the original. The flat cable is simply plugged in.The display in the Roland JP8000 is mounted on plastic bolts that are firmly connected to the display frame of the synthesiser, but these plastic bolts are much too high for the new OLED display at 8 mm. It is best to shorten these bolts to 5 mm so that the new OLED display comes very close to the windscreen. These plastic bolts can be easily sawn off with a small modelling handsaw. In our picture it is a saw from Tamiya.The big advantage is that a shim can be placed underneath as a height stop. This allows me to saw off the correct height very safely.Scope of delivery Roland JP8000 OLED Display:OLED display ready wiredInstallation instructionsmounting materialThe color of the shown display, may differ from the original.Installation service for Roland JP8000:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.