Korg Kronos 88

Jalco

YKB21-5074 - Phone Jack 1/4 - 6.3 mm PCB Stereo with switch

Phone Jack 1/4 inch- 6.3 mm, stereo with switch, for printed circuit used in Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5074SCJ630P5PJ603Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Synth-Parts

Rotary Poti vertikal, 11x11 10kOhm

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos - MIX SectionRoland MC-909Yamaha RS-7000 - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Jalco

YKB21-5006 - Phone Jack 1/4- 6.3 mm for printed circuits Stereo

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 6 .88*

KORG

Contact rubber 12P for RH3 Keyboard

1 piece Contact rubber 12 points for RH3 KeyboardContact high: 7,5 mmStrip bright: 22,3 mmStrip length: 165 mmNumber of contacts: 12A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 88 keys 7 contact strip + 4 pins are needed. The remaining 4 contacts can be easily separated from a rubber contact strip with 12 contacts. A notch is provided in the rubber contact strip after every four contacts for this purpose.

€ 10 .79*

KORG

Replacement keys for RH3 Keyboard, ivory

Key: Key A

Replacement Keys for RH3 KeyboardRH3 keyboard is used inKorg Kronos 73Korg Kronos 88KorgSP-250Korg SV-1 Color: cream white (Ivory)The RealHammer 3 keyboard (RH3) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 21.4 cm with a width of 2.24 cm. The depth of the key is 5.7 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is not formed on the keyboard but on the hammer. At the back end, the key is held in the keyboard frame by means of a slot. The black keys have a length of 16.4 cm with a width of 1.2 cm. 4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping. Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful.

Variants from €7.90*

€ 9 .89*

KORG

Korg RH3 Keyboard Spring

1 pcs Korg RH3 Keyboard Spring

€ 4 .17*

KORG

Rotary VR Knob for Korg KRONOS

1 pcs. Knob for rotary potentiometers inKorg Kronos 61Korg Kronos 73Korg Kronos 88ROTARY VR KNOB (KRONOS) X5870 VR KNOB(H) E30459-1 Specifications:Diameter top: 9 mmDiameter bottom: 10 mmHight: 14 mmShaft: 6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

€ 8 .34*

Jalco

Phone Jack 1/4 - 6.3 mm PCB Stereo with switch

Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 5 .81*

Panasonic

tactile switch 9,5 mm Korg

tactile switch suitable for KorgThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

KORG

Pitch Bend Assembly for Korg Pa3/4-series

1 pcs. Pitch bend Assembly for Korg Music Production WorkstationKorg KronosKorg Kronos 2Korg Pa3XKorg Pa3X ProKorg Pa4XKorg Pa4X ProKorg Pa300Korg Pa600Korg Pa700Korg Pa900Korg Pa1000This pitch bend unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all.

€ 38 .00*

KORG

Korg RH3 keyboard felt keylimit upper

1 Pc Korg Top Keystroke Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 4 times.

€ 9 .50*

KORG

Korg RH3 keyboard felt hammerlimit upper

1 Pc. Korg Upper Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 1 times.

€ 29 .68*

KORG

Hammer for RH3 Keyboard hammer black zone 1

Hammer: Hammer Zone 1 black key

Replacement Hammer for RH3 KeyboardThe RealHammer 3 (RH3) keyboard is a 4 zone hammer mechanism.

€ 8 .95*

Synth-Parts

Replacement stereo rotary potentiometer 14mm for Korg Kronos

Replacement stereo rotary potentiometer 14mm widht suitable forKorg KronosElectrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .45*

KORG

Korg Kronos Slider VR Knob

1 pcs. Korg Kronos Slider VR KnobKorg Kronos 61Korg Kronos 73Korg Kronos 88Korg Kronos Slider VR Knob X09130 SVR KNOB-B/G E40805-2Technical Description of Korg Kronos Slider Knob:This Slider knob will be put on slide potentiometer on your Korg Kronos Synthesizer. There is no tool needed.

€ 8 .34*

KORG

Korg RH3 Tastatur hammer lower limit felt

1 Pc. Korg Lower Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 2 times.

€ 9 .50*

Synth-Parts

Slide potentiometer with 30mm Travel for Korg M3, Kronos

Slide potentiometer with 30mm travel. Suitable forKorg M3Korg Kronos 61Korg Kronos 73Korg Kronos 88Korg spare part No.: 500365011400Specifications:Resistance: 10 kOhmtravel: 30 mmTechnical description:The potentiometer has a sliding path of 30 mm. Praktical tip:The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

From

€ 9 .56*

KORG

Korg RH3 Keyboard felt keylimit lower

1 Pc. Korg RH3 Bottom Keystroke Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 2 times.

€ 9 .50*

KORG

Korg Pitch Bend Potentiometer - discontinued

1 pcs. Korg Pitch Bend PotentiometerThis is a replacement Poterntiomter for Korg Pitch Bender. This Potetniomter will fit in a realy large range of Korg Instruments.In doubt please compare spare part number with your Service Manual.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):THis Potenziometer is a very spezial part. This one will only fit for Korg Pitch Bend.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .79*

KORG

Korg Pitch Bend 2 pcs. Potentiometer with PCB- discontinued

1 Set Korg Pitch Bend Potentiometer witch PCB KLM2304 / KLM2305This is a replacement Poterntiomter for Korg Pitch Bender. This Potentiomter will fit in a realy large range of Korg Instruments.In doubt please compare spare part number with your Service Manual.This is a set of two Potentiometers for Korg Pitch Bend.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Korg Pitch Bend.Replacement for PCB KLM2304 and KLM2305Useful hint:This Potenziometer is ready mounted on the PCB. For replacement you have only to connect the cable.

€ 14 .90*

KORG

Korg Kronos Button Large

1 pcs. Button largeKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 9 .06*

KORG

Korg Kronos Button Small

1 pcs. Button SmallKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 9 .06*

KORG

Parts for RH3 Keyboard

Spare Parts for RH3 KeyboardHere you will find parts for RH-3 Keyboard, like Felts, Springs and Contact Rubber

€ 3 .90*

Filter products

Korg Kronos 88