Yamaha DX5

1 pcs. CR2032 with 2 solder pin suitable forYamaha DX7, DX7 II, DX9, DX27, DX100Yamaha TG77Yamaha RX5, RX7, RX11Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The distance between the solder legs is 15 mm.Manufacturer: Panasonic or VartaPractical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable for Yamaha DX7Yamaha DX9Yamaha DX11Yamaha DX21Yamaha DX27Yamaha DX100 This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, mono with switch, for printed circuit used Roland or Yamaha InstrumentsPay attention! The solder contacts are arranged staggertly.The item is the same asHLJ 0521-01-1110HLJ 0541-01-1110HLJ 1520-01-3110HLJ 1540-01-3110This part is used inRoland Ersatzteilnummer 13449125  Yamaha Ersatzteilnummer LB203090Yamaha Ersatzteilnummer LB301930Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip for phone jack:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5078HLJ-2305HTJ-064-16DThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

1 pcs. slide potentiometer with 30mm travel. Suitable Slider forData Entry für  Yamaha DX7 Yamaha DX9 Yamaha DX11Yamaha DX27 Yamaha DX100 This volume control with the labelling EWANA0C10B14 is no longer available from the manufacturer Panasonic, because it is no longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.  Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. weighted Key's suitable for Yamaha FS-Keyboardin earlier times this Yamaha Fs Keyboard was also used in Korg Instruments.Please choose your spare part with dropdown menue on left side.Color: cremewhiteThis key is used and in a good kondition  

Slider Set for Yamaha DX-Serie - EWA-NFOC potentiometerSlider Set suitable for modelsYamaha DX 7Yamaha DX9Yamaha DX11Yamaha DX21Yamaha DX27Yamaha DX100Set contains:1 pcs. Slider for Volume1 pcs. Slider for Data EntryUseful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Power cabel 2m with 2P plug for Yamaha  InstrumentsVDE testedCable: H05VV-F2G0,75mm²Socket: C10Mains plug CEE 7/7 earth contactLength: 2 m  

1 pcs. Yamaha DX5 OLED Display NEW whiteReady-to-plug prepared OLED display for replacement in Yamaha DX5. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Mechanical hints for the replacement of the OLED display in the Yamaha DX5:The mechanical effort required to remove the display from the instrument is relatively simple in this case. The cover of the synthesizer can be lifted up after loosening a few screws. Now the circuit board on which the display is mounted must be unscrewed. The display itself is screwed on and the cable is plugged in.Recommendation:Disconnect the circuitry that generated the backlight voltage for the old display. Simply cut off two components using small side cutters.Instructions are included with the display.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha DX5 OLED Display NEW blueReady-to-plug prepared OLED display for replacement in Yamaha DX5. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Mechanical hints for the replacement of the OLED display in the Yamaha DX5:The mechanical effort required to remove the display from the instrument is relatively simple in this case. The cover of the synthesizer can be lifted up after loosening a few screws. Now the circuit board on which the display is mounted must be unscrewed. The display itself is screwed on and the cable is plugged in.Snipping off the metal tab:The OLED display is inserted into metal brackets in the Yamaha DX5. A small metal tab needs to be snipped off here. This can be done using a pair of side cutters.Recommendation:Disconnect the circuitry that generated the backlight voltage for the old display. Simply cut off two components using small side cutters.Instructions are included with the display.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

 1 pcs. Cap round for power switch

1 pcs. TRANSISTOR 2SC2555Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Yamaha DX5 OLED Display NEW yellowReady-to-plug prepared OLED display for replacement in Yamaha DX5. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Mechanical hints for the replacement of the OLED display in the Yamaha DX5:The mechanical effort required to remove the display from the instrument is relatively simple in this case. The cover of the synthesizer can be lifted up after loosening a few screws. Now the circuit board on which the display is mounted must be unscrewed. The display itself is screwed on and the cable is plugged in.Recommendation:Disconnect the circuitry that generated the backlight voltage for the old display. Simply cut off two components using small side cutters.Instructions are included with the display.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

Yamaha DX5 Recapping set Switching Power Supply 230 VACRecapping Set for 230VAC version.The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage. Warning: Switching power supplies store high amounts of energy for long periods of time. You are working on assemblies that operate at 230 V AC and approx. 300 V DC.You are carrying out this work at your own risk and under your own responsibility.With an age of more than 30 years, the Yamaha DX5 is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the power supply in the Yamaha DX5.Warning PSU Recapping:Risk of electric shock: Switching power supplys store high voltage and high energy for a very long period of time.When working with these spare parts offered here, you are working directly in a 230VAC circuit.Observe polarity. Incorrect installation will cause explosion and fire.For experts only: Be aware of dangers of electric current 

1 piece Yamaha DX5 OS Version 6.0 EPROMwe offer here last known OS version for the Yamaha DX5Mounting instructions for the EPROM in the Yamaha DX5:The EPROMs in the Yamaha DX5 are socketed and can be carefully prised out of their sockets.Older OS versions consist of two EPROMs, each with 128K. The EPROM for the latest OS version 6.0 consists of just one EPROM with 256K. The EPROM for OS version 6.0 is inserted into the socket for IC12.Depending on the serial number of the Yamaha DX5, two jumper wires may need to be re-soldered.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version.