Technics SX-PR900

Synth-Parts

Technics Pedalcable No2

1 pcs. Technics Pedalcable No2Pedal cable (2 meter) with plug used by Technics E-Piano models.Technics PC26Technics PR305Technics PR307Technics PR336Technics PR54Technics PR602Technics PR700Technics PR702Technics PR604Technics PR804Technics PR900Technics PR902Technics PR1000Technics PX201Technics PX203Technics PX207Technics PX224Technics PX332Technics PX336Technics PX662Technics PX663Technics PX664This cable is also used on other Technics E-Piano modell but the pin assignment differs.The cable fits variants with 3 pedals and has a 4 pol mini Din plug.Handcrafted faithfully reproduction made by Synth-Parts

€ 38 .50*

Synth-Parts

Hammer Felt 1 for Technics E-Piano Keyboard

1 pcs. Hammer Felt 1 for Technics E-Piano KeyboardThis results in very loud rattling when playing.Source of this rattling are the hammers. The hammers will no longer stopped by the felt and so the hammers clicking to the metall frame.A remedy here is the use of a new felt that is glued behind the original felt. A simple one, but effective solution.Made in Germany.You will need one for a complete Keyboard.One-sided self-adhering

€ 7 .89*

Synth-Parts

Hammer Felt 2 for Technics E-Piano Keyboard

Hammer Felt 2 for Technics E-Piano KeyboardThis results in very loud rattling when playing.Source of this rattling are the hammers. The hammers will no longer stopped by the felt and so the hammers clicking to the metall frame.We created a new felt that is based on a two componnent material like the original one. Here you has to replace the original felt with this new one.You will need 2 of these felts for a complete Keyboard.One-sided self-adheringInstallation note:Unfortunately, the old felt is difficult to access. It is very time-consuming to remove the old felt completely because the felt is difficult to access. Unfortunately, we have not had a good idea to simplify this. Gluing in the new felt is quite easy.

€ 10 .48*

Visaton

6,5 inch Speaker for Technics EAS-16PL NEW

1 pcs. 6,5 inch low-midrange speaker as replacement for Technics EAS-16PL470A3 or EAS-16PL403Asuitable forTechnics E-PianosTechnics Keyboardstechnical description:The speaker built in originally from Technics has become porous and brittle with age. We have found in cooperation with the Visaton the best possible replacement speaker and we are proud to offer this one here.This speaker is a low-midrange driver with a strong bass. The installation dimensions of the speaker are 170 mm in diameter at an installation depth of 73 mm. For fastening the speaker has four bores in the housing which are mounted on a diameter of 159 mm. The original Technics speaker has a 3 mm smaller diameter for fastening. The installation of the new speaker can be a little bit difficult.Practical tip:The speaker is mechanically fixed wirh 4 nuts. The electrical connection is made with plug-in cable shoes. We deliver a cable shoe adapter. This is necessary because the new speaker to the positive terminal has a larger cable lug used as the original Technics speakers.

€ 39 .00*

ALPS

Encoder 12 mm Technics short axis

1 pcs. Encoder 12 mm footprint and extra short axis suitable for modelsTechnics KN5000Practical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 14 .40*

Technics

Hammer for Technics E-Piano Keyboard

Hammer: Hammer black key

Hammer for a Technics E-Piano, 88 Key HammeractionThe hammers are used and in good condition. All keys supplied by us have been tested.2. different hammer versions:Please pay attention to the details. This Technics keyboard is also available with a pressure point simulation. The hammers in this keyboard version are constructed slightly differently in detail. Please take a close look.Technics has always used the same keyboard for many years. Today it has the advantage that the spare parts are easily interchangeable between the different instruments.We are of the opinion that Technics has used a very good and above all durable keyboard here. In addition to the good sound of the electric pianos, this is a definite plus point in favour of Technics electric pianosAssembly instructions:To be able to use a hammer, the keyboard must at least be unscrewed. This allows the keyboard as a whole to be pushed slightly away from the front edge. Now the key must be unscrewed. The hammer can then be removed from the top.

€ 9 .39*

Synth-Parts

MOSFET FS30KMJ-03

1 pcs. FS30KMJ-03Pch Power MOSFET Housing: TO220VDss: - 150VId: - 30APd: 35WTechnical hint:The defect of the power MOSFET is only the secondary fault effect. Conclusion: replacing the MOSFET will not be a long-term fix.

€ 4 .96*

Synth-Parts

MOSFET FX30KMJ-03

1 pcs. FX30KMJ-03Pch Power FX30KMJ-03 Housing: TO220VDss: - 30VId: - 30APd: 25WTechnical hint:The defect of the power MOSFET is only the secondary fault effect. Conclusion: replacing the MOSFET will not be a long-term fix.

€ 4 .96*

Technics

Key Guide NEW for Technics E-Piano Keyboard

Replacement–set for broken key guides on Technics electric pianosWith Technics electric pianos, it can happen over time that the original key guides break because of aging. This leads to a hanging or grinding of the keys. Since there are no more original spare parts for Technics, we have been looking for an alternative. Through various application tests and material research, we have found a product that fulfills the characteristics of the original Technics key guides in an identical way. Therefore we offer you a matched spare part set for your Technics piano in our store. Why we don't have the parts rebuilt?For the reproduction of a plastic part, an individually made injection mold must be produced. Due to the rather special shape of the original key guide, the effort is very high and expensive. This would drive up the final selling price dramatically and would simply not be profitable for us. But since we have tested our product extensively, we can sell our alternative with a clear conscience. So that everyone can get an impression of our product and the handling or the exchange, we have prepared a suitable blog post and a PDF variant to print out. You will also receive a printed manual with the product when you order it. Included in the set:– Matched tube suitable for a keyboard with 88 keys.– Special keyboard grease– Instruction manualWhen replacing the key guides, it is necessary to grease the new parts. For this reason, a suitable grease especially for electric pianos is included in the set.

€ 37 .50*

ALPS

Volume Slider for Technics

1 pcs. Slidepotentiometer with 25mm Travel. Suitable for Volume Slider forTechnics PR-Serie E-Pianos Technics PX-Serie E-Pianos Technics P-Serie Stage-Pianos These potentiometers fit the vast majority of Technics keyboard instruments. There are few exceptions where this does not fit. Please look ahead.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 9 .75*

Panasonic

tactile switch 7 mm technics

1 pcs. tactile switch suitable for Technics E-Pianos and Keyboardssuitable for: PX20PX73PX101PX103PX111PX222PX663PR307KN5000KN6000KN7000 The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

Technics

Cap quadratic for power switch in Technics E-Pianos

Cap quadratic for power switch suitable in Technics E-PianosTechnics PX101Technics PX103Technics PX107Technics PX111

€ 7 .90*

Technics

Fader knob for Technics E-Piano

1 pcs. Fader knob suitable for:Technics E-PianoColor: Blach with white line

€ 9 .52*

Technics

Holder QMRG7029A for Technics E-Pianos

1 pcs. holder QMRG7029A for Technics E-PianosThis part is made of plastic

€ 4 .76*

Technics

Holder QMRG7028for Technics E-Pianos

1 pcs. holder QMRG7028for Technics E-PianosThis part is made of plastic

€ 4 .76*

JST

JST FJ Plug 5 pin for printed circuits

JST FJ Plug 5 pin for printed circuitthis FJ Plug form JST is used by Technics E-Pianos for connecting Printid Circuit Boards. Pitch: 2.0 mmThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 1 .79*

JST

JST FJ Plug 10 pin for printed circuits 10PL-FJ

JST FJ Plug 10 pin for printed circuitthis FJ Plug form JST is used by Technics E-Pianos for connecting Printid Circuit Boards. Pitch: 2.0 mmThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 1 .79*

JST

JST FJ Socket 10 pin for printed circuits 10R-FJ

JST FJ socket 10 pin for printed circuitthis FJ Socket form JST is used by Technics E-Pianos for connecting Printid Circuit Boards. Pitch: 2.0 mmThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 1 .79*

JST

JST FJ Socket 5 pin for printed circuits

JST FJ socket 5 pin for printed circuitthis FJ Socket form JST is used by Technics E-Pianos for connecting Printid Circuit Boards. Pitch: 2.0 mmThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 1 .79*

Technics

Keys for Technics E-Piano

Parts Keyboard: Hammer black Key

Key's for a Technics E-Piano, 88 Key HammeractionThe keys are used and in good condition. All keys supplied by us have been cleaned and checked.Since these are used keys, color deviations may occur. Technics has always used the same keyboard for many years. We think Technics has used a very good and above all durable keyboard.

Variants from €7.40*

€ 9 .90*

Technics

Spare Parts Keyboard for Technics E-Piano, used

Parts Keyboard: Spring

Spare Parts for Technics E-Piano Keyboard, 88 Key hammeractionThis parts are usedTechnics Key-Guide:we know this problem with key guides in Technics E-Pianos. For this we have designed this alternative replacement key guide:Technics Key Guide

€ 0 .95*

Technics E-Piano SX-PX900

Under the brand name Technics the electric piano PR-900 was manufactured and put on the market in the period from 1996 to 1998. The Technics PR900 Epiano is a piano with a very extensive range of functions. The selling price was in 1996 around 3.500, - Euro.

Main Differrence between PR700 and PR900

The main difference between the two models is that the PR900 also has an electronic DRAWBAR.

Sound Group

In the Sound Goup, you select the sound you want to play with. The main grand and piano sounds can be selected directly via control buttons. The other sounds like Fender Rhodes, Wurlitzer or organ can be selected via the large LCD display. Also on classical instruments this epiano offers a lot of sound variety. Whether it's a harp, oboe, flute or a brass instrument, you can choose from the menu.

Rhythm Group

The Auto Accompaniment provides you with a variety of preset rhythm functions such as Rock, Beat or Latin. The Technics PR-700 features many standard rhythms such as march and waltz, blues, soul and disco. Even on something unusual rhythms such as fusion, big band, swing or country, this electric piano has a lot to offer.
All this can be selected directly on the control panel on the control panel or alternatively, the electric piano offers a large LCD display to navigate clearly through the various functions.

One touch play
The One Touch Play feature makes it easy for the piano player to control the extensive auto accompaniment features.

To round off the range of functions, the PR900 also has a sequencer and a composer. Thus, the electric piano is also suitable as a music workstation for composing.

The standard in the 1990's was the MIDI interface and the possibility to save data and compositions on a 3.5 inch floppy disk drive.

The velocity-sensitive keyboard on the Technics PR-900 is designed as a hammer action keyboard. For the keyboard used here, we know this model as the most durable and low-maintenance keyboard on the whole e-piano market.

Spare parts and Repair of a Technics E-Piano PR900

For repair purposes, we have many components of electrical engineering such as tact switch, potentiometers and encoders available from stock. Should anything be broken in the keyboard, we can certainly help with matching keys, springs or hammers.
In case of serious errors in electronics, contact us confidentially or a specialist company in your area who can repair your electric piano. In many cases, it is sufficient for us to send electronic components. We can repair these professionally. When installing and removing electronics assemblies, you are welcome to contact a specialist company on site or a recognized specialist company in electrical engineering.

Filter products

Technics SX-PR900

Technics E-Piano SX-PX900

Main Differrence between PR700 and PR900

Spare parts and Repair of a Technics E-Piano PR900