Sequential Circuits
1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5078HLJ-2305HTJ-064-16DThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
Tactile switch suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Tactile switch with black button and red LED suitable forSequential Circuits Prophet VSÂ The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. brand new Sequential Circuits, SCI Potentiometer 10kOhmSequential Circuits Prophet 5 REV1    Serial 1 - 182Sequential Circuits Prophet 5 REV3    Serial from 1301 to EndSequential Circuits Prophet 10This potentiometer is only for the instruments built between 1978 and 1984.The potentiometers that were installed in the Prophet 5 and also in the Prophet 10 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 10 KOhmChanges to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread         Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.     The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. Battery with 3 solder pins suitable for  RPlease check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's
Slider set brand new Sequential Circuits, SCI Potentiometer forSequential Circuits Prophet 5 REV1    Serial 1 - 182Sequential Circuits Prophet 5 REV3   Serial from 1301 to endThe potentiometers that were installed in the Prophet 5 and also in the Prophet 10 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 10 KOhmQuantity: 26 pcs.Changes to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread         Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.     The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.
1 pcs. OLED Display New forSequential Circuits Prophet VSSequential Circuits Prophet VS RackSequential Circuits Studio 440To replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.
1 pcs. Tactile switch with orange button and red LED suitable forSequential Circuits Prophet VSÂ The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Slide Potentiometer 10 KOhm for  Data Entry Sequential Circuits Prophet VS KeyboardThe original fader cap is difficult to fit. The dimensions of the sliding pin differ slightly from the original.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Battery with solder pin suitable for  Sequential Circuits Propeht 5Please check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's
Complet replacement set tactile switch for Sequential Prophet VSconsist of:1 pcs. orange button + 1 red LED1 pcs. blue button + 1 red LED8 pcs. black button + 1 red LED10 pcs. blue button31 pcs. black buttonOperational Life for all switch: 3.000.000 CyclesThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Slide Potentiometer 10 KOhm for  Data Entry Sequential Circuits Prophet VS RackThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. brand new Sequential Circuits, SCI Potentiometer 100kOhmSequential Circuits Prophet 5 REV2    Serial 183 - 1300This potentiometer is only for the instruments built between 1978 and 1984.The potentiometers that were installed in the Prophet 5 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 100 KOhmChanges to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread         Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.     The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
Slider set brand new Sequential Circuits, SCI Potentiometer forSequential Circuits Prophet 5 REV2    Serial 183 - 1300The potentiometers that were installed in the Prophet 5 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 100 KOhmQuantity: 26 pcs.Changes to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread         Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.     The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.
1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m
AC Power Inlet with AMP Connectortechnical Dates:Termination AMP Socket 4,3 mm  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with AMP Sockets.The electrical load is 10 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.
1 pcs. Tactile switch with blue button and red LED suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Tactile switch with black button suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Tactile switch with blue button suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
Order spare parts for Sequential Circuits easily online.
Synthesizers and samplers are devices that are exposed to a continuous load and must withstand it reliably. This is true for private use, as well as for professional use. If the smallest components do not work, the entire system cannot deliver the desired first-class sound. We offer in our store Sequential Circuits spare parts products that continue brand quality even after replacement in the usual way. This includes synthesizer spare parts and sampler spare parts, but also encoder for Sequential Circuits, jack socket for PCB mounting or LCD display for Sequential Circuits.All Sequential Circuits spare parts in our store have one thing in common: they convince in material and workmanship quality. We know that when musicians are hitting the keys or technicians are doing their job, there is no time for long breakdowns. Therefore, the Sequential Circuits spare parts are optimally compatible and can be replaced without any problems and, above all, quickly and easily. The gig or rehearsal can continue immediately afterwards. Just give us a call or send an email if you are not sure which spare part for Sequential Circuits you should buy, or which synthesizer spare parts or sampler spare parts are the right ones for the models you use. We will be happy to advise you!
Do not compromise on quality
A system is only as powerful as its smallest component. This means for you that Sequential Circuits spare parts should also be purchased and installed in brand quality that you know from the manufacturer. This applies to tact switch for Sequential Circuits, as well as to the LCD display for Sequential Circuits or any other Synthsizer spare parts. If you compromise here, you are making a big mistake. Professionalism, which you need on stage, is also essential for spare parts. No matter if you want to buy an potentiometer for Sequential Circuits or a tact switch for Sequential Circuits, the same professional quality is appropriate as if a device is bought completely. For all questions we are happy to help you. Jack for PCB? Symthesizer spare part? No matter what you need: We advise you competently, so that your favorite music can sound as usual again. Online ordering is quick and uncomplicated, and we are always your efficient contact partner when it comes to installing the spare parts.