Quasimidi

Fatar

Contact rubber for Fatar Keyboards

Rubbercontact: 12 Contacts

Contact rubber for Fatar KeyboardsFatar uses in many different keyboards same contact rubber. The here offered contact rubber are suitable for!!!!! Not for use in Roland Instruments !!!!!Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP/10 MDRFatar TP/10 ABSFatar TP/40Fatar TP/100LRtechnichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greyFatar Keyboards are used by Clavia Nord, Döpfer, Ensonic, Korg, Kurzweil, GEM

Variants from €5.00*

€ 10 .95*

ALPS

Quasimidi LED-tactile switch 8 x 8 x 8,5 mm Red heavy push

1 pcs. Quasimidi LED-tactile switch suitable for modelLED colour: Red We offer here switch from the second redesigned series where LED body is clear.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 4 .52*

Synth-Parts

Nut UNF 7/16 Inch Plastic

1 pcs. Nut UNF 7/16 Inch for Phone JackTechnical descriptionThis nut fits to 1/4 Inch Phone Jacks. The nut is build from Plastic and has thread UNF 7/16 Inch. The thickness is 6/32 Inch and wrench size is 1/2 Inch.

€ 0 .88*

Fatar

Replacement keys and parts for Fatar TP/8S Keyboard

Key: Key A

Replacement keys and spare parts for Fatar TP/8S Keyboard, weightedWe would like to expressly point out that the keys are used. Fatar keys tend to darken and yellow significantly. Under certain circumstances, it may be that we currently only have very darkened keys in stock.Fatar TP/8S keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white.

€ 9 .75*

Synth-Parts

Rotary potentiometer for quasimidi plastic axis

1 pcs. Replacement rotary potentiometer plastic axis suitable forQuasimidiElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. The axis has a diameter of 6 mm and is Knurled on a length of 7 mm. It is made of Plastik. Its head has ends in corner radius.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .50*

Synth-Parts

Quasimidi button cap blue

1 pcs. Quasimidi button cap blue Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 4 .49*

Synth-Parts

Quasimidi button cap clear

1 pcs. Quasimidi button cap clear Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 4 .49*

Synth-Parts

Rotary potentiometer for quasimidi metal axis

1 pcs. Replacement rotary potentiometer suitable forQuasimidiElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 9 .50*

Synth-Parts

Phone Jack 1/4 inch for printed circuits Mono 2 switch

1 pcs. Phone Jack 1/4 inch, Mono for printed circuit 2 switchSpecification:MonoThread: UNF 7/16 InchHousing: PlasticThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 2 .99*

ALPS

Quasimidi LED-tactile switch 8 x 8 x 8,5 mm Red light push

From

€ 4 .52*

Synth-Parts

Quasimidi Sirius Rotary potentiometer set plastic axis

Set Quasimidi Sirius Rotary potentiometer set plastic axisnot for VolumeThis set contains 23 Potentiometer.Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. The axis has a diameter of 6 mm and is Knurled on a length of 7 mm. It is made of Plastik. Its head has ends in corner radius.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 74 .95*

Synth-Parts

10 pcs. quasimidi Rotary potentiometer set metal axis

10 pcs. quasimidi Rotary potentiometer set metal axisNot for VolumeElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 68 .98*

Synth-Parts

Quasimidi Polymorph Rotary potentiometer set plastic axis

Set Quasimidi Polymorph Rotary potentiometer set plastic axisnot for VolumeThis set contains 43 Potentiometer.Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. The axis has a diameter of 6 mm and is Knurled on a length of 7 mm. It is made of Plastik. Its head has ends in corner radius.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 138 .99*

Synth-Parts

Quasimidi Rave-O-Lution 309 Rotary potentiometer set plastic axis

Set Quasimidi Rave-O-Lution 309 Rotary potentiometer set plastic axisnot for VolumeThis set contains 35 Potentiometer.Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. The axis has a diameter of 6 mm and is Knurled on a length of 7 mm. It is made of Plastik. Its head has ends in corner radius.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 113 .98*

Synth-Parts

Quasimidi Polymorph Rotary potentiometer set metal axis

Quasimidi Polymorph Rotary potentiometer set metal axisNot for VolumeThis set contains 43 PotentiometerElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 155 .00*

Synth-Parts

Quasimidi Sirius Rotary potentiometer set metal axis

Quasimidi Sirius Rotary potentiometer set metal axisNot for VolumeThis set contains 23 PotentiometerElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 83 .49*

Synth-Parts

Quasimidi Rave-O-Lution 309 Rotary potentiometer set metal axis

Quasimidi Rave-O-Lution 309 Rotary potentiometer set metal axisNot for VolumeThis set contains 35 PotentiometerElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 127 .00*

Synth-Parts

10 pcs. quasimidi Rotary potentiometer set plastic axis

10 pcs. quasimidi Rotary potentiometer set plastic axisnot for VolumeElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. The axis has a diameter of 6 mm and is Knurled on a length of 7 mm. It is made of Plastik. Its head has ends in corner radius.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 59 .94*

Synth-Parts

Quasimidi Sirius Encoder 22 mm

1 pcs. Quasimidi Sirius Encoder 22 mmPractical advice: Original encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases can be removed. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 10 .71*

Filter products

Quasimidi