Roland XV-88
Panasonic
tactile switch 5 mm for Roland
1 pcs. tactile switch suitable for models RolandFP1, FP2, FP3, FP4, FP5, FP6, FP7, FP8, FP-50JV25, JV30, JV35, JV50, JV80, JV90, JV880, JV1080JP8000JD800 - Cursor ButtonsMC-303, MC-307RD-500XP10, XP50, XP60, XP80XV3080U20Fantom X6,X7,X8 without REC/PLAY/STOPOnly for non-illuminated buttons:A90, A90-EXXP30JV1000JP8080RD-600,RD-700Roland Part Number: 13169697 or 13169752The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
€
0
.71*
Roland
Replacement parts for Roland PA4 and PA4A Keyboard
Ersatzteile Tastatur:
Fulcrum 12P
Spare parts for Roland PA4 and PA4AKeyboardHere you will find different parts for Progressive Hammer Action Keyboard from Roland. These PA4 Keyboard was build by Roalnd in two different Versions. There exists a PA4 and a PA4A Version. The Parts i offer here fits for both Versions. Cusion, FeltHammerKey GuidePrice is valid for one spare part. Lower Cusion for Hammer in a Roalnd PA4 or Pa4A Keyboard (PArt-No: TTROPA4-ZU-FLTHA1)This Cussion is needed to stop hammer when falling down.Roland use here a material based on two different components.One side is self-adhesive.For a complette Keyboard wit 88 Keys you will need 2 of these cusionTTROPA4-ZU-FLTHA1.For all other Felt and Cusions you will need one part for a complete Keyboard.Please have a look at the video for replacing Hammers.
Variants from €1.49*
€
17
.90*
Synth-Parts
Power cable 3 pol C13 Socket, 1.8 m
1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m
€
6
.45*
ALPS
LED-tactile switch 8 x 8 x 8,5 mm Yellow
LED-tactile switchLED colour: yellowThe construction part is not longer built. The old serial number was KHJxxx. With that serial number the part was built during the 80s.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
€
3
.45*
Roland
Replacement Keys for Roland PA4A Keyboard
Taste:
Key A
Spare parts for Roland PA4A KeyboardDoes a key on your electric piano hang or clack loudly when you play it? In these cases, it is usually not the key that is defective but the underlying hammer that is broken.
This part fits for all Roland PA4A Keyboards
Roland PA4A Keyboard is used in
Roland A90 and A90exRoland FP-1 and FP-8 and FP-9Roland HP-145 and HP-147Roland HP-236 and HP-237 and HP-245Roland HP-2800 and HP-2880Roland HP-330 and HP-335 Roland HP-3800Roland HP-530 and HP-535 and HP-550 and HP-555Roland HP-5700Roland HP-730Roland RD600Roland XV-88
The S-Key fits in Keyboard PA4 AND PA4A. You can find it here: TTROPA4-KBLPlease have a look at the video for replacing Hammers.
Variants from €9.53*
€
9
.98*
Synth-Parts
Roland JD-800 Volume Potentiometer
1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland JD-800 VolumeRoland XV-88 VolumeThe plastic lever must be shortened. The original potentiometer has a 5 mm sliding pin.This volume control with the labelling EWANA0X5B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.
€
8
.33*
Roland
Roland PA4 contactrubber for Keyboard
1 pc. Contact rubber for Roland PA4 keyboardFeatures: Height of contacts: 9 mm width of the strip: 32 mm Length of the strip: 165 mm Number of contacts per strip: 12 contactsRoland spare part number: 22185247This contactrubber fits in Roland PA4 and also Roland PA4A Keyboard.One contact strip consists of 12 contacts and thus covers one octave. For a complete replacement of the contact strips in a keyboard with 88 keys, 7 contact strips + 4 contacts are needed. The remaining 4 contacts can easily be separated from a contact strip with 12 contacts. For this purpose, a notch is provided in the contact strip after every 4 contacts.
€
11
.90*