Yamaha DX-Series

ALPS

tactile switch 7,3 mm

1 pcs. tactile switch suitable for modelsKorg DW6000, DW8000Korg Poly 61Korg KPR 77Roland JX 8PRoland TR606, TB303Yamaha DX7, DX9Oberheim Matrix 6Kurzweil K1000Kurzweil K2000Part Number: Korg: 37505000, Roland: 1129715,Yamaha: KA905510The old productnumber was called: KHC10901The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 0 .99*

ALPS

tactile switch 4,3 mm Yamaha

tactile switch suitable for modelsYamaha DX7II, DX7IID, DX7IIFDYamaha SY77, SY99Yamaha Part no: KA907030 und VF946200The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 0 .71*

Synth-Parts

Phone Jack 1/4 - 6.3 mm for printed circuits Mono with switch

1 pcs. Phone Jack 1/4 inch- 6.3 mm, mono with switch, for printed circuit used Roland or Yamaha InstrumentsPay attention! The solder contacts are arranged staggertly.The item is the same asHLJ 0521-01-1110HLJ 0541-01-1110HLJ 1520-01-3110HLJ 1540-01-3110This part is used inRoland Ersatzteilnummer 13449125 Yamaha Ersatzteilnummer LB203090Yamaha Ersatzteilnummer LB301930Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip for phone jack:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 2 .44*

Varta

CR2032 Solder pin for Yamaha DX-Series

1 pcs. CR2032 with 2 solder pin suitable forYamaha DX7, DX7 II, DX9, DX27, DX100Yamaha TG77Yamaha RX5, RX7, RX11Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The distance between the solder legs is 15 mm.Manufacturer: Panasonic or VartaPractical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

€ 3 .49*

Synth-Parts

PP Capacitor 22 nF Safety

1 pcs. PP Capacitor 22 nF Safety

€ 1 .99*

E-Switch

Single pole push switch, 250V/5A with solder lugs SDDLD10900

Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

€ 6 .95*

Synth-Parts

Recapping Set PSU for Yamaha DX7,DX9

Recapping set Power Supply for Yamaha DX7,DX9The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha DX series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the power supply in the Yamaha DX7, DX9. Spare part number of the PSU board: LC90330 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 19 .40*

Yamaha

Replacement keys and parts for FS Keyboard

Taste: Aftertouch 76

1 pcs. weighted Key's suitable for Yamaha FS-Keyboardin earlier times this Yamaha Fs Keyboard was also used in Korg Instruments.Please choose your spare part with dropdown menue on left side.Color: cremewhiteThis key is used and in a good kondition

Variants from €0.67*

€ 88 .99*

Synth-Parts

Yamaha DX-Serie Volume Slide potentiometer - EWA-NFOC

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable for Yamaha DX7Yamaha DX9Yamaha DX11Yamaha DX21Yamaha DX27Yamaha DX100 This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 7 .98*

Synth-Parts

Yamaha DX7 Recapping Set Mainboard

Recapping set Mainboard for Yamaha DX7The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha DX series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the Mainboard in the Yamaha DX7, DX9. Spare part number of the PSU board: LC90370 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 16 .54*

Synth-Parts

Slider Set for Yamaha DX-Serie - EWA-NFOC potentiometer

Slider Set for Yamaha DX-Serie - EWA-NFOC potentiometerSlider Set suitable for modelsYamaha DX 7Yamaha DX9Yamaha DX11Yamaha DX21Yamaha DX27Yamaha DX100Set contains:1 pcs. Slider for Volume1 pcs. Slider for Data EntryUseful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 11 .90*

Nichicon

Bipolar Capacitor 4.7uF/25V for Audio, Radial, Nichicon Muse ES

1 piece bipolar Elko 4.7uF/25V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .86*

Synth-Parts

Yamaha DX7 OLED Display NEW blue LCD Replacement

Color: Blue

1 pcs. OLED Display blue New forYamaha DX7Yamaha DX9This Display replacement is a really easy swapping. You will only need a screwdriver.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

€ 54 .70*

Synth-Parts

Yamaha DX-Serie Slidepotentiometer Data Entry - EWANA0C10B14

1 pcs. slide potentiometer with 30mm travel. Suitable Slider forData Entry für Yamaha DX7 Yamaha DX9 Yamaha DX11Yamaha DX27 Yamaha DX100 This volume control with the labelling EWANA0C10B14 is no longer available from the manufacturer Panasonic, because it is no longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part. Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 7 .98*

Synth-Parts

Cable straight thru 12,7 x 11,7 mm

1 pcs. Cable straight thru 12,7 x 11,7 mmThis Cable straight thru is used by 2 pol power cords.Dimensions of mounting hole: 12,7 x 11,7 mm

€ 0 .68*

Hosiden

Phone Jack 1/4 - 6.3 mm for printed circuits Stereo with 2 switch

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo with two switch, for printed circuitThis part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Yamaha DX7Technics SX -PX20Technical descriptionThe offered phone jack for PCB mounting is a stereo jack two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 3 .99*

Synth-Parts

5 pcs. Contact Cleaning Stripes for electrical contacts

5 pcs Contact Cleaning Stripes for electrical contacts These contact cleaning stripes are spezial developed for cleaning electrical Contacts.The strip consists of a kind of paper that is quite hard, does not fuzz and is abrasion resistant. The strip was then soaked with a special cleansing solution.

€ 11 .90*

Synth-Parts

Yamaha DX21 OLED Display NEW, LCD Replacement

Color: Blue

1 pcs. OLED Display New forYamaha DX21This Display replacement is a really easy swapping. You will only need a screwdriver.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

€ 54 .70*

Synth-Parts

Yamaha DX7 II OS Version 1.9 EPROM

1 piece EPROM with Yamaha DX7 II OS version 1.9we offer here a OS version for the Yamaha DX7 IIMounting instructions for the EPROM in the Yamaha DX7 II:Soldering may be required if the EPROM in the Yamaha DX7 II is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version.

€ 16 .95*

Synth-Parts

Quartz 9,6 MHz

1 pcs. Quartz 9,6 MHzsuitable forYamaha DX7 Master Clock OSCYamaha DX9 Master Clock OSC

€ 0 .83*

Yamaha

Replacement keys and spare parts for Yamaha C61KG Keyboard

Auswahl Ersatzteil: Contactrubber 61P new

Spare parts for Yamaha C61KG KeyboardYamaha C61KG Keyboard is used inYamaha QS-300Yamaha QS-700Yamaha SY-22Color/tint: creme white

Variants from €2.36*

€ 27 .89*

Panasonic

Yamaha DX II-Serie Volume Slide potentiometer

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable forYamaha DX IIYamaha DX IIDYamaha DX IIFD----- Discontinued - out of production -------Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 9 .98*

Panasonic

Yamaha DX II Serie Slide potentiometer

1 pcs. Slide potentiometer with 30mm travel. Suitable forYamaha DX II - Data EntryYamaha DX IID - Data EntryYamaha DX IIFD - Data Entry This part is no longer availabel from Yamaha.This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 9 .98*

Jalco

DIN female 5 pin MIDI for printed circuits, Jalco, YKF51-5066

1 pcs. MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5066used by:KorgRolandYamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

€ 13 .09*

Batteriewechsel bei Yamaha DX7:

Beim Yamaha DX7 besteht das Problem das keine Faktory Sounds über eine Tastenkombination geladen werden können. Wenn die Batterie leer ist oder im spannungslosen Zustand getauscht wird sind alle Sounds weg. Es gibt grundsätzlich zwei Wege die Faktory Sounds wieder ins Instrument zu laden. Über Midi oder über ein Data Cardrige.

Data Cardrige:

das ist sicherlich der einfachste Weg, wenn man denn irgendwo noch ein Cardrige hat.

Midi:

hier wird es etwas komplizierter da mit den heutigen PC's die Datenübertragung in vielen Fällen mittendrin abbricht. Nach mehrmaligen Übertragungsversuchen hat man meistens trozdem Glück und die Sounds sind wieder da.

Nicht Vergessen:

erst mal das Instrument aus und wieder einschalten. Dann sollte alles wieder da sein.

Filter products

Yamaha DX-Series

Batteriewechsel bei Yamaha DX7: