Korg Pa-Serie

Synth-Parts

Korg tactile switch 6.2 SMD 3.1 mm ground

1 pcs. SMD tactile switch with higth 3.1 mm ground Attention: SMD (Surface Mounted Device) needs spezial soldering equipment and spezial experience in solderingThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 0 .84*

Fatar

Contact rubber for Fatar Keyboards

Rubbercontact: 12 Contacts

Contact rubber for Fatar KeyboardsFatar uses in many different keyboards same contact rubber. The here offered contact rubber are suitable for!!!!! Not for use in Roland Instruments !!!!!Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP/10 MDRFatar TP/10 ABSFatar TP/40Fatar TP/100LRtechnichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greyFatar Keyboards are used by Clavia Nord, Döpfer, Ensonic, Korg, Kurzweil, GEM

Variants from €5.00*

€ 10 .95*

Jalco

YKB21-5012 - Phone Jack 1/4- 6.3 mm for printed circuits Mono

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit used in Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5012HLJ 4306HLJ 4306-01-3000Mono with switchit is used by the following manufaturesKorg partnumber: 454004300Roland partnumber: 13449146Yamaha partnumber: VB312600 YKB21-5012Yamaha partnumber: VE742000 HLJ 4306These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Jalco

YKB21-5078 - Phone Jack 1/4- 6.3 mm for printed circuits Stereo

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5078HLJ-2305HTJ-064-16DThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 6 .88*

E-Switch

1 pcs. Single pole push switch, 250V/5A with solder lugs SDDLD10900

1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

€ 9 .45*

Panasonic

tactile switch 5 mm Korg

1 pcs. tactile switch suitable for models Korgis40, is50Pa1 XPro, Pa2 XProPa50 without LCD BoardPa60, Pa80, Pa500, Pa800SP200Korg Part Number: INT0001008The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

ALPS

Value Slider 30mm Travel for Korg

1 pcs. Mono Slider with 30mm Travel. Suitable for Value Slider for KorgN1, N5, N5ex, N264, N36401W, 01WFDX2, X3, X5, X5dM1, M1r, M3rT1, T2, T3WS, WSEXKorg spare part No.: 365007800The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 11 .45*

KORG

LED 3 mm Blue for Korg Pa

1 piece LED 3 mm Blue This LED is a technical equivalent to the orignial Korg LED's.The LED are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 1 .29*

KORG

Singlel Button with LED-window 17x7 mm for Pa3

Single Button 17 x 7 mm, dark grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 7 .29*

KORG

Singlel Button with LED-window 17x7 mm for Pa3

Single Button 17 x 7 mm, light grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 7 .29*

KORG

Button 19 mm with LED window for Pa4x

1 pcs Button 19 mm with LED window for Pa4x Do you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 12 .28*

ALPS

Single pole push switch, 250V/5A with solder pins for PCB

1 pcs. Single-pole push switch in the switch design - OFF with solder Pins for PCB mounting suitable for modelsKorg EA-1Korg EMX-1Korg ER-1Korg Part Number: 375014800technical Dates:Voltage: 250VACCurrent: 5ATermination Solder PinVDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for P.C.B. mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

€ 9 .45*

Synth-Parts

SMD tactile switch 5 mm

SMD tactile switch suitable for models KorgPa50 only LCD BoardKorg Part Number: MP5010102Attention: SMD (Surface Mounted Device) needs spezial soldering equipment and spezial experience in solderingDimensions:Length: 6mmDeep: 6mmhigh: 5mmThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 0 .82*

KORG

Singlel Button 17x7 mm, NO LED window for Pa3

Single Button 17 x 7 mm (No Window)Korg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 7 .29*

Fatar

Replacement keys and parts for Fatar TP/7 Keyboard

Key: Key A

Replacement keys and spare parts for Fatar TP/7 Keyboard Fatar TP/9 keyboard is a touch sensitive keyboard with unweighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 14,5 cm and a width of 2.24 cm. The thickness of the keys is 1 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is not worked out. The distance from the front side of the key is 9,5 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white.

Variants from €2.75*

€ 9 .29*

KORG

Pitch Bend Assembly for Korg Pa3/4-series

1 pcs. Pitch bend Assembly for Korg Music Production WorkstationKorg KronosKorg Kronos 2Korg Pa3XKorg Pa3X ProKorg Pa4XKorg Pa4X ProKorg Pa300Korg Pa600Korg Pa700Korg Pa900Korg Pa1000This pitch bend unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all.

€ 38 .00*

KORG

Singlel Button with LED-window 19x9 mm for Pa3 darkgray

Single Button 19 x 9 mm, dark grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 19 x 9 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 7 .29*

KORG

Singlel Button with LED-window 19x9 mm for Pa3 lightgray

Single Button 19 x 9 mm, lihgt grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 19 x 9 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 7 .29*

KORG

Korg PA4x Black panel button 15x7mm, NO LED window

1 pcs Korg PA4x Black panel button 15x7mm, NO LED windowDo you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 15 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 13 .19*

Fatar

Replacement keys, weighted for Fatar TP/8+ Keyboard

Key: Key A

Replacement keys, weighted for Fatar TP/8+ KeyboardFatar TP/8+ keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white.

€ 13 .90*

KORG

Fader knob for KORG Pa3 - discontinued-

1 pcs. Fader knob suitable for:Korg Pa3XKorg Pa3X Pro

€ 7 .29*

KORG

Korg Pa4x Single panel button 19 mm without LED window

1 pcs Single panel button 19 mm without LED window, for Korg PA4x Do you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 10 .10*

KORG

Fader knob for KORG Pa1-Pa3

1 pcs. Fader knob suitable for:Korg Pa1XKorg Pa1X ProKorg Pa2XKorg Pa2X ProKorg Pa3XKorg Pa3X ProKorg Pa800

€ 7 .29*

KORG

Singlel Button UP for Pa1X

Single Button UPKorg Pa1XKorg Pa1X ProKorg Pa2XKorg Pa2X ProKorg Pa800Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 5 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 7 .29*

Filter products

Korg Pa-Serie