Nord Stage 2 EX

Contact rubber for Fatar KeyboardsFatar uses in many different keyboards same contact rubber. The here offered contact rubber are suitable for!!!!!   Not for use in Roland Instruments    !!!!!Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP/10 MDRFatar TP/10 ABSFatar TP/40Fatar TP/100LRtechnichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greyFatar Keyboards are used by Clavia Nord, Döpfer, Ensonic, Korg, Kurzweil, GEM

1 pcs. Clavia Nord Volume Dreh Potentiometer Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 16 mm Diameter, the total length without pins is 32 mm. In this total length the casing is 9 mm long. On this casing is the thread with 7 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 4 mm and is flattened on a length of 12 mm. It is made of metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. Screw 16 mm Black PhillipsLength: 16 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one is used for red side panels.

1 pcs. Screw 6 mm Black PhillipsLength: 6 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one can be located on rear side or on bottom.

1 pcs. Nord Pedal Spring  

1 pcs. Clavia Nord Knob with line  4 mmThis control knob fits on a 4 mm D-axis. Nord used these knobs on older models. Especially for the volume potentiometer.Praktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs. Clavia Nord Knob Praktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs. Nord Encoder 22 mm for Nord Stage 2 with DetentOriginal Nord spare part. Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Encoder 22 mm without Detent.Also suitable for:Nord Modular G2  - Secondary Dial Master Clock -> Patch LevelPractical adviceThe encoders offered here come from the same manufacturer as those used by Nord. There are small deviations in design compared to the original:Pin distance here is 2.5 mm compared to 5 mm for the originalOriginal encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases at Nord and can be removed. These encoder are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs.Clavia Nord LCD Display new white Replacement LCD Display for Claiva Nord Instruments. For installation soldering is requiered.Notes on installation for Nord LCD Display:This LCD Display is soldered to a PCB only with a small connector. This requieres very good soldering knowlege. Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 20,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.  

1 pcs Clavia Nord PSU Transformer 22770 Electrical properties of 22770:Primary: 230 V AC or 2 x 115 V ACSec: 4 x 7,5 Volttransformer for PCB mountingPractical advice:Plug of the device. Don't work under Voltage. 

1 pcs. Encoder 22 mm suitable forNord NordStage 2  - Main DialPractical advice:The encoders offered here come from the same manufacturer as those used by Nord. There are compared to the original small deviations in design:Pin distance here is 2.5 mm compared to 5 mm for the originalOriginal encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases at Nord and can be removed. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Clavia Nord cape for Encoder older modells Praktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs. Clavia Nord Knob Encoder older modells Praktical tip:The knobs are just plugged on. No tools are needed.