E-Mu Proteus

Tactile switch suitable for  The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.Why should I solder new pushbutton

1 pcs. Encoder 22 mm suitable for some E-MU Systems instrumentsE-mu ESIE-mu E4XT     depends on manufacturing dateE-mu e6400   depends on manufacturing dateE-mu e-synth ultraE-mu Proteus 1Practical advice:this encoder was used in some few E-Mu Instruments. Please have a look in your instrument first if this is the right one for you. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Battery with solder pin suitable for  E-Mu ProteusPlease check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Power cabel 3m with 3P C13 plug   

Recapping set forE-Mu Proteus 1E-Mu Proteus 2E-Mu ProcussionThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.This Recapping Set contains all necessary Capacitors for Switching Power Supply and Mainboard. Warning PSU Recapping:Risk of electric shock:Switching power supplys store high voltage and high energy for a very long period of time.When working with these spare parts offered here, you are working directly in a 230VAC circuit.Observe polarity. Incorrect installation will cause explosion and fire.For experts only: Be aware of dangers of electric current  

1 pcs. OLED Display New forE-Mu Proteus 1E-Mu Proteus 2E-Mu Proteus 3To replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for modelsE-Mu  -  Mounting Frame must be taken overPlease note: Not suitable for all E-Mu devices.technical Dates:Voltage: 250VACCurrent: 6ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for soldering. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 15 mm, a length of 30 mm and a height of 9 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m

1 pcs. triple MIDI DIN socket female 5 pin for printed circuit for E-MuJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. This is a 1:1 replacement for the MIDI jack in most e-mu sampler.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

 1 pcs. Cap round 12 mm for tact switchThis cap for stylus has a diameter of 12 mm and a receptacle of 3 x 3 mm.Suitable as a spare part for E-Mu sampler

 1 pcs. Cap round for power switch

1 pcs. Phone Jack 1/4- 6.3 mm, stereo witch one Switch, for printed circuit used by E-mu E4KE-mu E-SynthE-Mu E4 XTE-Mu e6400Technical description:The offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.