Rotary-Potentiometer

Synth-Parts

Alesis Andromeda Potentiometer Post Filter

1 pcs. Replacement rotary potentiometer suitable for Alesis Andromeda A6 - Post FilterWe have set out on a search!Alesis used potentiometers manufactured by Panasonic in the Andromeda A6. Unfortunately, Panasonic has stopped the production of this potentiometer series. In addition, there is the fact that the potentiometers from Panasonic have a few special features so that most commercially available potentiometers can not be used.After a lengthy research, which unfortunately did not lead to a positive result, we decided to build a potentiometer especially for the Alesis Andromeda A6.Shaft and guide are made of metal: We deliberately chose a potentiometer with a metal shaft and guide. We are convinced that this leads to a much longer life span than the original Panasonic potentiometers where shaft and guide are made of plastic.Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 9 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 17,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:67 pcs. - to replace all small Potentiometer in your Alesis Andromeda A6 you will need 67 of these.The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 3 .15*

Synth-Parts

Rotary Poti vertikal, 11x11 10kOhm

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos - MIX SectionRoland MC-909Yamaha RS-7000 - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Synth-Parts

Rotary Poti vertikal, 11x11 10kOhm center click

Rotary Potentiometer vertikal 11x11 mm with center click, 10kOhmSubstitute rotary potentiometer for Roland MC-909The rotary pot fits also inKorg electribe EMX1 Korg electribe ESX1here the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Nord

Clavia Nord Volume Dreh Potentiometer

1 pcs. Clavia Nord Volume Dreh Potentiometer Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 16 mm Diameter, the total length without pins is 32 mm. In this total length the casing is 9 mm long. On this casing is the thread with 7 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 4 mm and is flattened on a length of 12 mm. It is made of metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 15 .90*

Synth-Parts

Replacement stereo rotary potentiometer for Roland Fantom X-series, volume control EVJY10FB6A24

1 pcs. Replacement stereo rotary potentiometer for Roland Fantom X-series, suitable for volume control and ext. Level - EVJY10FB6A24Roland Fantom SRoland Fantom FARoland Fantom X6Roland Fantom X7Roland Fantom X8Roland RD-64This volume control is no longer available at the original equipment manufacturer Roland, because Panasonic, the producer of the pot, does not longer produce the production-model. The here shown replacement pot is identical in construction and 100% compatible with the original Roland part volume EVJY10FB6A24.Electrical properties:The stereo nominal resistance has 20 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 x 12 mm, the total length without pins is 22,5 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 10 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 13,8 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 6 .25*

Yamaha

Yamaha Pedal Potentiometer

1 pcs. Yamaha Pedal PotentiometerThis is a replacement Poterntiomter for Pedal from E-Piano if there is a Volume Pedal installed.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Pedal.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 9 .89*

Synth-Parts

Roland Juno 106 Replacement stereo rotary potentiometer

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inRoland Juno 106Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 17 mm, the total length without pins is 31,5 mm. In this total length the casing is 11 mm long. On this casing is the thread with 5 mm length connected. The axis has a diameter of 6 mm. It is made of Metall. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The six solder pins are 1 mm wide (one of them) and they are arranged in two rows in a distance of 5 mm (pitch).Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .99*

Synth-Parts

Korg EMX1 stereo Potentiometer 12 mm

1 pcs. Replacement stereo rotary potentiometer 12mm widht suitable forKorg EMX1Korg ESX1Not a 1:1 spare part. The original potentiometer is threaded. Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The six solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .99*

Synth-Parts

Rotary potentiometer,center Click for Roland MC-505

1 pcs. Replacement rotary potentiometer with center click suitable forRoland MC-303 LFO DepthRoland MC-505Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 6 .55*

Yamaha

Pedal Volume Potentiometer

1 pcs. Pedal Volume PotentiometerThis is a replacement Poterntiomter for Pedal from E-Piano if there is a Volume Pedal installed.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Pedal.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 14 .95*

Synth-Parts

Rotary potentiometer for Roland MC

1 pcs. Replacement rotary potentiometer suitable forRoland MC 303Roland MC 505Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 6 .55*

Yamaha

Yamaha Potentiometer for Pitch Bend

1 pcs. Rotary Potentiometer for pitch bend suitable forYamahaResistance: 10 KOhm

€ 13 .78*

Synth-Parts

Replacement stereo rotary potentiometer for Korg

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inKorg Volca Sample 2Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .60*

Synth-Parts

Sequential Circuits Potentiometer 10K, SCI Prophet 5

1 pcs. brand new Sequential Circuits, SCI Potentiometer 10kOhmSequential Circuits Prophet 5 REV1 Serial 1 - 182Sequential Circuits Prophet 5 REV3 Serial from 1301 to EndSequential Circuits Prophet 10This potentiometer is only for the instruments built between 1978 and 1984.The potentiometers that were installed in the Prophet 5 and also in the Prophet 10 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 10 KOhmChanges to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm. The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 10 .71*

Synth-Parts

Roland Juno 6 60 JX3P Replacement stereo rotary potentiometer

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inRoland Juno 6Roland Juno 60Roland JX3PElectrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 17 mm, the total length without pins is 31,5 mm. In this total length the casing is 11 mm long. On this casing is the thread with 5 mm length connected. The axis has a diameter of 6 mm. It is made of Metall. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The six solder pins are 1 mm wide (one of them) and they are arranged in two rows in a distance of 5 mm (pitch).Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .99*

Synth-Parts

Potentiometer for Yamaha rm1x with center Tap 12mm

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionYamaha RM1x Utility Mounting instruction Yamaha RM1x:The potentiometer with thread I offer here can also be used in the RM1x. The great advantage of this solution is that I think potentiometers with threads will have much longer lifetime than potentiometers without threads. Indisputably, the axis is guided and stored much more stably by the thread.n the pictures you see a test installation I have made.Electrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 4 .70*

Yamaha

Yamaha Montage Super Knob Rotary Potentiometer

1 pcs. Yamaha Montage Super Knob Rotary PotentiometerYamaha Montage 6Yamaha Montage 7Yamaha Montage 8Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 9 .84*

Synth-Parts

Stereo rotary potentiometer 12mm for Korg

1 pcs. Replacement stereo rotary potentiometer 14mm suitable forKorg KROMEElectrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm widht, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the axis rises with 18 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The six solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .84*

Synth-Parts

Replacement stereo rotary potentiometer 14mm for Korg Kronos

Replacement stereo rotary potentiometer 14mm widht suitable forKorg KronosElectrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .45*

Yamaha

Yamaha Replacement stereo rotary potentiometer 14mm

stereo rotary potentiometer for Volume, suitable forYamaha PSR-330 und 340PSR-530 bis 550PSR-630 und 640PSR-730 und 740PSR-1000, 1100, 1500PSR-2000, 2100, 3000PSR-S700 und S710PSR-S900 und S910CVP-207Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 6mm. It is made of black plastic. Its head has a slot and ends in corner radius.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 1 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 5 .77*

Synth-Parts

Replacement stereo rotary potentiometer for Korg

Replacement stereo rotary potentiometer suitable for volume control inKorg 05RWKorg TR RackKorg X5DRThis volume control is no longer available by Korg. The here shown replacement pot is build with a 2,5 mm longer axis.Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch). At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 6 .55*

Synth-Parts

Rotary Pot for LCD Contrast L=15 B10K

Rotary potentiometer for LCD Contrast adjustmentThis pot is for these models:M1, M1r, M3rT1, T2, T3WavestationKorg spare part No.: 360021200The potentiometer is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 4 .44*

Synth-Parts

Rotary Pot for LCD Contrast Kurzweil

Rotary potentiometer for LCD Contrast adjustment The potentiometer is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 4 .34*

Synth-Parts

Nord Modwheel Potentiometer

1 pcs. Potentiometer for Modwheel suitable forNord Modular G2The potentiometer is firmly soldered. For replacing craftsmanship and experience in soldering is required.

€ 22 .61*

Rotary-Potentiometer

Filter products

Rotary-Potentiometer