Roland MKS-50

Xvive Audio

Xvive MN3009 256 Stage BBD DIP8

1 pcs. Xvive MN3009 256 Stage BBD DIP8 - Panasonic MN3009 cloneRebuild of the MN3009 BBD from Panasonic. We think that it is a 1:1 clone from original Panasonic Chip. Comment from a college:Noise level and spectrum similar to that of an intact Panasonic MN3009. In direct comparison with a usual defective Panasonic chip (which still works, but just typically rushes) was the difference between sea surf and reasonably constant background noise clearly. That is spoken in some forums of completely noise-free, I can not understand ..... FeaturesVariable delay time from 0.64ms to 12.8msWide dynamic range 88dB (typ)Total harmonic distortion <0.3%Clock frequency from 10Hz to 200KHz Package: DIP-8 Mechanical Description:The IC is housed in a DIP 8 package and is designed for trughhole mounting on a circuit board. THis chip is pin compatible to Panasonic MN3009.ICs are sensitive to static charge! Handle with care. Semiconductors are excluded from exchange.

From

€ 12 .44*

Nichicon

Bipolar Capacitor 4,7uF/50V for Audio, Radial, Nichicon Muse ES - Discontinued -

1 piece bipolar Elko 4,7uF/50V for Audio circuits - Discontinued -Manufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .89*

Jalco

YKB21-5012 - Phone Jack 1/4- 6.3 mm for printed circuits Mono

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit used in Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5012HLJ-0520-01-010HLJ 4306HLJ 4306-01-3000Mono with switchit is used by the following manufaturesKorg partnumber: 454004300Roland partnumber: 13449146Yamaha partnumber: VB312600 YKB21-5012Yamaha partnumber: VE742000 HLJ 4306These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Jalco

YKB21-5010 - Phone Jack 1/4 - 6.3 mm PCB Stereo

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used in Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5010HLJ0520-01-010HLJ1520-01-3010HTJ-064-10Dsame PCB layout, different housingHLJ4416-01-3020it is used by the following manufaturesKorg partnumber: 454004400Roland partnumber: 13449125 HLJ0520-01-010Roland partnumber: 13449145 YKB21-5010Yamaha partnumber: VE382300Technical description Jalco YKB21-5010:The offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. This phone jack is available from various manufacturers in the same mechanical and technical construction. An exception is the manufacturer HOSIDEN using a wider housing. The electrical connection has the same structure.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .56*

Nichicon

Bipolar Capacitor 10uF/16V for Audio, Radial, Nichicon Muse ES

1 piece bipolar Elko 10uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .98*

Synth-Parts

Phone Jack 1/4 - 6.3 mm for printed circuits Mono with switch

1 pcs. Phone Jack 1/4 inch- 6.3 mm, mono with switch, for printed circuit used Roland or Yamaha InstrumentsPay attention! The solder contacts are arranged staggertly.The item is the same asHLJ 0521-01-1110HLJ 0541-01-1110HLJ 1520-01-3110HLJ 1540-01-3110This part is used inRoland Ersatzteilnummer 13449125 Yamaha Ersatzteilnummer LB203090Yamaha Ersatzteilnummer LB301930Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip for phone jack:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 2 .44*

Nichicon

Bipolar Capacitor 47uF/16V for Audio, Radial, Nichicon Muse ES

1 piece bipolar Elko 47uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .81*

Nichicon

Bipolar Capacitor 47uF/50V for Audio, Radial, Nichicon Muse ES

1 piece bipolar Elko 47uF/50V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 1 .25*

SCHULZKABEL

Power cable 2 pol for Roland, 2m

Power cabel 2m with 2P plug for Roland InstrumentsVDE testedCable: H05VV-F2G0,75mm²Socket: C10Mains plug CEE 7/7 earth contactLength: 2 mAlso forKorgAkai

€ 9 .64*

Synth-Parts

IC Socket DIP16 Gold for IC

1 pcs. IC Socket DIP 16 Gold for ICTechnical Hint:Mounting of this part requiers soldering.

€ 1 .14*

Synth-Parts

Roland MKS-50 OS Version 3.0

1 piece EPROM with ROLAND MKS-50 OS version 3.0 with OLED Support.we offer here a Customized OS version for the Roland MKS-50. This OS version is required if a new OLED display is to be installed in the MKS-50.Mounting instructions for the EPROM in the Roland MKS-50:Soldering may be required if the EPROM in the Roland MKS-50 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version.

€ 23 .49*

Varta

CR2032 with 3 Solder pin for Roland MKS series

1 pcs. CR2032 with 3 solder pin suitable forRoland MKS-50Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The positive pole owns two interconnected soldering legs at a distance of 10 mm. The negative pole has one solder leg.Practical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

€ 3 .28*

Jalco

Roland triple female MIDI Socket, Jalco, YKF51-5046

1 pcs. triple MIDI DIN socket female 5 pin for printed circuit - Roland MIDI3-NSJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. The original MIDI jack in your instrument will certainly look somewhat different. Today's possible replacement of this 3-way MIDI jack looks slightly different, but is identical in function. used by:Roland These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 10 .89*

Synth-Parts

Roland MKS-50 Recapping Set

Recapping set for Roland MKS-50The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the complete Instrument.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 29 .50*

Synth-Parts

Roland MKS-50 OLED Display new

Color: Blue

1 pcs. Roland MKS-50 OLED Display brandnew Ready-to-plug display for the exchange in the Roland MKS-50. For this exchange you only need a screwdriver. We deliver the display ready wired.Roland used a display in the MKS-50 which is no longer available. So that our new OELD display can be installed without problems, we have developed a compensation frame. The display is mounted on this frame. The compensation frame for the OLED display in the Roland MKS-50 is included in delivery. Advice to Eprom Version in Roland MKS-50Does the display only show half? That is, the first 8 characters are displayed normally but the remaining 8 characters remain dark? This can happen with an old Eprom version in the instrument. In this case the Eprom must be replaced by a current OS version.Notes on installation OLED Display in Roland MKS-50:We deliver this OLED dislpay for the Roland MKS-50 synthesizer ready for installation. All necessary cables are already soldered on. We deliver a 3D printet frame for mounting OLED in your Synthesizer. You will only need a screwdriver for the installation.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime of OLED Displays:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

€ 83 .99*

ALPS

tactile switch 9,5 mm Roland

tactile switch suitable for models RolandRoland D-550Roland MKS-50Roland MKS-70Roland Spare Part Number: 13129733The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .64*

Synth-Parts

IC Socket DIP 8 Gold for IC

1 pcs. IC Socket DIP 8 Gold for ICTechnical Hint:Mounting of this part requiers soldering.

€ 1 .99*

Synth-Parts

IC Socket DIP 28 Gold for IC

1 pcs. IC Socket DIP 28 Gold for ICTechnical Hint:Mounting of this part requiers soldering.

€ 2 .81*

Understanding the Roland MKS-50 Synthesizer Module

The Roland MKS-50 is a renowned synthesizer module that has been cherished by musicians and sound designers for its unique sound capabilities and robust performance. As with any vintage electronic instrument, maintaining and upgrading the MKS-50 ensures its functionality and longevity.

Essential Spare Parts for the Roland MKS-50

To keep your MKS-50 in optimal condition, it is crucial to have access to high-quality synthesizer spare parts. Components such as the sensor board, potentiometer, and encoder are vital for the module's performance. Replacing worn-out parts with reliable OEM spare parts ensures the synthesizer maintains its original quality.

Enhancing Functionality with Display Upgrades

Upgrading the display of your MKS-50 can significantly improve its usability. Replacing the old screen with an LCD display replacement or opting for an OLED display upgrade provides better visibility and modernizes the interface.

Repairing and Maintaining the PCB

The printed circuit board (PCB) is the heart of the MKS-50. Over time, components may deteriorate, necessitating PCB repair. Professional services can address these issues, ensuring the synthesizer operates seamlessly.

End-of-Life Spare Parts and Professional Repair Services

As the MKS-50 is a vintage instrument, some components may be classified as EOL spare parts. Sourcing these parts from reliable suppliers and utilizing a professional repair service can help in maintaining the synthesizer's integrity and functionality.

By understanding the importance of maintenance and utilizing quality parts and services, you can ensure that your Roland MKS-50 continues to deliver exceptional performance for years to come.

Filter products

Roland MKS-50

Understanding the Roland MKS-50 Synthesizer Module

Essential Spare Parts for the Roland MKS-50

Enhancing Functionality with Display Upgrades

Repairing and Maintaining the PCB

End-of-Life Spare Parts and Professional Repair Services