Roland
Single-pole push switch in the switch design - OFF with solder pins for PCB mounting suitable for modelsKorg Korg Part Number:The power switch corresponds to the ALPS switches SDDLD12200 TV3. This is no longer manufactured by ALPS.Termination Solder pinMounting PCBVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for PCB mounting. Therefor are tow solder pins as Snap-In pins in the front. The spacing of the snap in pins is 16 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 4 A at 250 VAC.Knowledge in soldering is required for switch replacement.
LED-tactile switchLED colour: yellowThe construction part is not longer built. The old serial number was KHJxxx. With that serial number the part was built during the 80s.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
tactile switch with green LED suitable for modelsRoland JV-1000  only Patch-GroupPart No.: 13119708This switch fits also for this:Roland JV-1000 Edit/Track   difference: orange LEDThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
Dual Button for 12 x 5 mm Window Roland HP-900Roland HP-1700Roland KR-3000Roland U-20Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reasen for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 12 x 5 mm. This part has two Buttons and each button has a window for LED Light.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.
Fader knob for Roland SH201This fader knob fits for all fader on Roland SH201.This part is no longer aiviable.Original Roland spare part, newRoland spare part number: 4233323
tactile switch suitable for modelKorg DVP-1Korg EX8000Korg SDD-2000 und Korg SDD-3000Roland Fantom X6, X7 und X8Roland MC307Korg replacement part no: 37504800Roland  replacement part no: 894645The construction part is not longer built. The old serial number was KEC10010 With that serial number the part was built during the 1980s.The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Mainboard repair for Roland XP-50These Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.
1 pcs. Single Button for 17 x 5 mm with WindowRoland D-70Roland FP-8Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 5 mm. This part has one Buttons.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.
Electrolytical Capacitor 22uF/25V SMD The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Â
Electrolytical Capacitor 3,3uF/50V SMDManufakturer: Nichicon The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
1 pcs connection cable for your Roland PHA KeyboardThis Cable connects the Low, Mid and High Boards with the Mainborad of your Roland PHA Keyboard.Contacts:Â 16PPitch:Â Â Â Â Â Â 1,25 mmLength: Â Â 90 mmÂ
Contactrubber for Roland SK8 KeyboardRoland SK8 Keyboard is used inRoland JV-80Roland JV-90Roland JX-30Roland JX-35Roland JX-50Roland XP-30Roland XP-50Roland XP-60Attention: This blue contactubber do not fit in old SK8 Keyboards Â
Parts for Roland SK9 KeyboardsHere you will find all parts like springs, felt, aftertouch and P.C.B.
Roland Roland Jupiter-6 Fader Set comlete (Custom Built with dust cover for Synth-Parts)This Set contains:27 pcs. Fader 30mm  100KB These Potentiometers are brand new ALPS Potetntiometers Useful hint:Potentiometer are soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.
Recapping set for Roland  S-50 Sampler The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Roland Juno series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made of Capacitors, which have been specially developed for use in audio applications. For us is manufacturer Nichicon the manufacturer with a good quality at reasonable prices offers.Manufacturer: NichiconThe set consists of 88 electrolytical CapacitorsThe Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
Replacement Keys for Roland Progressive Hammer Action Keyboard- PHA2Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107eColor/tint: creme white (ivory)
1 pcs. LCD Display brandnew in amber forRoland JD-800this is a plug in ready Display replacement for Roland JD-800. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.
1 pcs. OLED Display brandnew in white forRoland JD-800this is a plug in ready Display replacement for Roland JD-800. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.
Blue LCD Display with LED Backlight replacement including cable Kit forRoland A-50Roland A-80We offer an absolutely equivalent display using modern LED technology for backlight.Color: black Character  / white BackgroundDelivery scope:DisplayMounting partsInstruction for replacementReady wired with original cableBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. We strongly recommend to disable electronic circuit that generates backlight voltage for old display. This is described in our manual. This work is to be done only by technically, best electrotechnically savvy people.
1 pcs. OLED Display brandnew in blue forRoland JD-800this is a plug in ready Display replacement for Roland JD-800. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.
1 pcs. Push Switch with solder Pins for PCB mounting suitable forRoland SH-101technical Dates:Termination Solder PinSupplied without capPractical advice:The original "On" switch in the Roland SH-101 is a switch with 8 connection legs. Since this is no longer available today, we have installed a switch with 6 connection legs on a trial basis. To our delight, we have found that this works.Knowledge in soldering is required for switch replacement.
1 pcs. Mainboard repair for Roland Roland HP-330Roland HP-530These Mainboard will repaired by us and fully working. We sell this repair with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.
Spare parts for Roland PA4A KeyboardDoes a key on your electric piano hang or clack loudly when you play it? In these cases, it is usually not the key that is defective but the underlying hammer that is broken. This part fits for all Roland PA4A Keyboards Roland PA4A Keyboard is used in Roland A90 and A90exRoland FP-1 and FP-8 and FP-9Roland HP-145 and HP-147Roland HP-236 and HP-237 and HP-245Roland HP-2800 and HP-2880Roland HP-330 and HP-335Â Roland HP-3800Roland HP-530 and HP-535 and HP-550 and HP-555Roland HP-5700Roland HP-730Roland RD600Roland XV-88 The S-Key fits in Keyboard PA4 AND PA4A. You can find it here:Â TTROPA4-KBLPlease have a look at the video for replacing Hammers.
Order spare parts for Roland easily online.
E-Pianos and Music Workstationare devices that are exposed to a continuous load and must withstand it reliably. This is true for private use, as well as for professional use. If the smallest components do not work, the entire system cannot deliver the desired first-class sound. We offer in our store Roland spare parts products that continue brand quality even after replacement in the usual way. This includes e-piano spare parts and music workstation spare parts, but also encoder for Roland, jack socket for PCB mounting or LCD display for Roland.All Roland spare parts in our store have one thing in common: they convince in material and workmanship quality. We know that when musicians are hitting the keys or technicians are doing their job, there is no time for long breakdowns. Therefore, the Roland spare parts are optimally compatible and can be replaced without any problems and, above all, quickly and easily. The gig or rehearsal can continue immediately afterwards. Just give us a call or send an email if you are not sure which spare part for Roland you should buy, or which e-piano spare parts or music workstation spare parts are the right ones for the models you use. We will be happy to advise you!
Do not compromise on quality
A system is only as powerful as its smallest component. This means for you that Roland spare parts should also be purchased and installed in brand quality that you know from the manufacturer. This applies to tact switch for Roland, as well as to the LCD display for Roland or any other E-Piano spare parts. If you compromise here, you are making a big mistake. Professionalism, which you need on stage, is also essential for spare parts. No matter if you want to buy an potentiometer for Roland or a tact switch for Roland, the same professional quality is appropriate as if a device is bought completely. For all questions we are happy to help you. Jack for PCB? E-Piano spare part? No matter what you need: We advise you competently, so that your favorite music can sound as usual again. Online ordering is quick and uncomplicated, and we are always your efficient contact partner when it comes to installing the spare parts.