1 pcs. tactile switch suitable for models KorgKorg 01W, 01WFD, 01RW, 01WProXKorg i2, i3, i4sKorg N264, N364Korg M1Korg T1, T21, T3Korg X2, X5Korg WavestationKorg 707    all expect 0 - 9Korg ProphecyKorg Part Number: 375010500 oder 375007500The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for models KorgLong life:This switch has a lifetime 10 times longer than the original switch Korg build inBX3, CX3              new Version build 2002i30ix300                    Attention: here are also two different switch on boardMS2000, MS2000RN1, N1R, N5SG-ProX, SGR, SP500Triton le, TR61, TR88, TR-Rackz1Korg Part Number: 374000200The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsKorg DW6000, DW8000Korg Poly 61Korg KPR 77Roland JX 8PRoland TR606, TB303Yamaha DX7, DX9Oberheim Matrix 6Kurzweil K1000Kurzweil K2000Part Number: Korg: 37505000, Roland: 1129715,Yamaha: KA905510The old productnumber was called: KHC10901The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece bipolar Elko 1uF/50V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Contact rubber for Fatar KeyboardsFatar uses in many different keyboards same contact rubber. The here offered contact rubber are suitable for!!!!!   Not for use in Roland Instruments    !!!!!Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP/10 MDRFatar TP/10 ABSFatar TP/40Fatar TP/100LRtechnichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greyFatar Keyboards are used by Clavia Nord, Döpfer, Ensonic, Korg, Kurzweil, GEM

1 pcs. SMD tactile switch with higth 3.1 mm ground Attention: SMD (Surface Mounted Device) needs spezial soldering equipment and spezial experience in solderingThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton 

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit used in Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5012HLJ-0520-01-010HLJ 4306HLJ 4306-01-3000Mono with switchit is used by the following manufaturesKorg          partnumber: 454004300Roland       partnumber: 13449146Yamaha     partnumber: VB312600     YKB21-5012Yamaha     partnumber: VE742000     HLJ 4306These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used in  Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5010HLJ0520-01-010HLJ1520-01-3010HTJ-064-10Dsame PCB layout, different housingHLJ4416-01-3020it is used by the following manufaturesKorg          partnumber: 454004400Roland      partnumber: 13449125   HLJ0520-01-010Roland      partnumber: 13449145   YKB21-5010Yamaha     partnumber: VE382300Technical description Jalco YKB21-5010:The offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. This phone jack is available from various manufacturers in the same mechanical and technical construction. An exception is the manufacturer HOSIDEN using a wider housing. The electrical connection has the same structure.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 piece bipolar Elko 10uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Phone Jack 1/4 inch- 6.3 mm, stereo with switch, for printed circuit used in  Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5074SCJ630P5PJ603Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. tactile switch suitable for models KorgBX3, CX3              new Version build 2002i30ix300                    Attention: here are also two different switch on boardMS2000, MS2000RN1, N1R, N5SG-ProX, SGR, SP500Triton le, TR61, TR88, TR-Rackz1Korg Part Number: 374000200The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

tactile switch suitable for KorgThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Contact rubber 12 points for RH4 Keyboard    Contact high:  7,5 mmStrip bright:   22,3 mmStrip length:  165   mmNumber of contacts: 12Roland Part Number: 4671145A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 88 keys 7 contact strip + 4 pins are needed. The remaining 4 contacts can be easily separated from a rubber contact strip with 12 contacts. A notch is provided in the rubber contact strip after every four contacts for this purpose.

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. tactile switch suitable for modelsKorg MonopolyKorg PolySixKorg BX3/CX3      first Version build in 1980'sRoland JX 10PRoland Jupiter 8Roland TR808Part Number: Korg: 37503400, Roland: 13169601The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos     -   MIX SectionRoland MC-909Yamaha RS-7000   - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. tactile switch suitable for models Korgis40, is50Pa1 XPro, Pa2 XProPa50                        without LCD BoardPa60, Pa80, Pa500, Pa800SP200Korg Part Number:  INT0001008The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece LED 3 mm Blue This LED is a technical equivalent to the orignial Korg LED's.The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece bipolar Elko 22uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Rotary Potentiometer vertikal 11x11 mm with center click, 10kOhmSubstitute rotary potentiometer for Roland MC-909The rotary pot fits also inKorg electribe EMX1 Korg electribe ESX1here the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Hammer Felt 1 for Technics E-Piano KeyboardThis results in very loud rattling when playing.Source of this rattling are the hammers. The hammers will no longer stopped by the felt and so the hammers clicking to the metall frame.A remedy here is the use of a new felt that is glued behind the original felt. A simple one, but effective solution.Made in Germany.You will need one for a complete Keyboard.One-sided self-adhering

1 piece Korg LS-88 Keyboard spring KOC-C50231 

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5078HLJ-2305HTJ-064-16DThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

SMD tactile switch suitable for models KorgPa50         only LCD BoardKorg Part Number:  MP5010102Attention: SMD (Surface Mounted Device) needs spezial soldering equipment and spezial experience in solderingDimensions:Length: 6mmDeep:   6mmhigh:    5mmThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton