1 pcs.  FFC cable 26 pin 1.25 pitch 420 mm Length = 420 mmsame side contacts.

1 pcs.  Roland JD800 FFC cable 26 pinKeyboard connection cablein Roland JD-800 Service Manual this cable is called FUJI CARD 26x420This cable is the connection cable between the Mainboard in Rolands JD800 and the Contact Board Assy under the Keyboard.There are 2 different keyboard cables in the Roland JD-800:According to our research, there exists two different keyboard versions in Roland JD-800, which means there are two different versions used of this cable. The difference in this cable is, in one type of this cable contacts are on the same side of cable. In second type of this cable contacts  are on one side on top and and on the opposite side at the other end of the cable contacts are down under.Please take a close look at your Roland JD-800 before ordering this cable. We have both cable versions on offer.This cable was produced in Germany in best qualtity.Length = 420 mmOpposit side connector 

1 pcs. LCD display with LED backlightsuitable forRoland W-30We offer here a high quality replacement display with modern LED technology for the backlight.Mounting of LCD Display is plug and play. No soldering is required.Color: white font/black backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable ready to plug in. Roland used in W30 a very special connector. We rebuild theses connector with handcraft pincompatible to the original one. Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland W30:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation. For this you have to cut two small componnents. No soldering is required.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.

1 piece EPROM with ROLAND MKS-50 OS version 3.0 with OLED Support.we offer here a Customized OS version for the Roland MKS-50. This OS version is required if a new OLED display is to be installed in the MKS-50.Mounting instructions for the EPROM in the Roland MKS-50:Soldering may be required if the EPROM in the Roland MKS-50 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

1 piece EPROM with ROLAND JUNO 1 OS version 4.0 with OLED Support.This OS works only in Juno-1.we offer here a Customized OS version for the Roland Juno1 . This OS version is required if a new OLED display is to be installed in the Juno1 .Mounting instructions for the EPROM in the Roland Juno1 :Soldering may be required if the EPROM in the Roland Juno1 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

1 pcs. Roland MKS-50 OLED Display brandnew Ready-to-plug display for the exchange in the Roland MKS-50. For this exchange you only need a screwdriver. We deliver the display ready wired.Roland used a display in the MKS-50 which is no longer available. So that our new OELD display can be installed without problems, we have developed a compensation frame. The display is mounted on this frame. The compensation frame for the OLED display in the Roland MKS-50 is included in delivery. Advice to Eprom Version in Roland MKS-50Does the display only show half? That is, the first 8 characters are displayed normally but the remaining 8 characters remain dark? This can happen with an old Eprom version in the instrument. In this case the Eprom must be replaced by a current OS version.Notes on installation OLED Display in Roland MKS-50:We deliver this OLED dislpay for the Roland MKS-50 synthesizer ready for installation. All necessary cables are already soldered on. We deliver a 3D printet frame for mounting OLED in your Synthesizer. You will only need a screwdriver for the installation.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime of OLED Displays:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Slide potentiometer with 20mm travel. Suitable forRoland TR-707Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements.The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Panasonic Battery holder CR2032 pinspacing 20 mmWe offer a battery holder that is suitable for standard CR2032 button cells. The advantages of this battery holder are its very secure battery retention and good pin spacing for circuit board mounting.This battery holder is used in many musical instruments.Technical Description of Panasonic Battery Holder:The battery holder is designed for circuit board mounting and has one solder leg for the positive pole and one solder leg for the negative pole.The distance between the two solder legs is 20 mm.A space measuring 25 mm x 26 mm is required for installation. 

1 pcs Dial Knob suitable forRoland Fantom X6Roland Fantom X7Roalnd Fantom X8

Slide potentiometer with 30mm travel. Suitable forKorg M3Korg Kronos 61Korg Kronos 73Korg Kronos 88Korg      spare part No.: 500365011400Specifications:Resistance: 10 kOhmtravel: 30 mmTechnical description:The potentiometer has a sliding path of 30 mm. Praktical tip:The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slide switch with solder Pins for PCB mounting suitable forRoland Juno 106 - DCO,VCF,VCAtechnical Dates:Termination Solder PinSupplied without capPractical advice:Knowledge in soldering is required for switch replacement.

Power cabel 2m with 3P C13 plug   

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland TB-303technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. triple MIDI DIN socket female 5 pin for printed circuit - Roland MIDI3-NSJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. The original MIDI jack in your instrument will certainly look somewhat different. Today's possible replacement of this 3-way MIDI jack looks slightly different, but is identical in function.  used by:Roland These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. 14 pin FFC socket with 1.25 mm pitch14 pinPitch: 1.25 mmLength: 21,05 mmdeepth:  4,80 mmhight:      7,80 mmTechnical descriptionPraktikal tip:In these socket the cable cable have just to be pluged in.

Roland Roland Juno 6 Fader Set comlete This Set contains:3 pcs. Fader 30mm    10KB1 pcs. Fader 30mm    10KA4 pcs. Fader 30mm    50KA4 pcs. Fader 30mm    50KB5 pcs. Fader 30mm   100KB2 pcs. Fader 30mm    1MA  Useful hint to Roland Juno 6 Fader Set:The lever on the original potentiometer is straight. The lever on the potentiometer offered here adapts to this shape because it is slotted.Arrangement of the solder pins: The solder pins on this replacement part are slightly offset. The solder pins must be bent slightly before soldering.The control is soldered firmly onto a circuit board. Replacing the control requires manual dexterity and experience in soldering. 

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 00Roland D-70, mainboard version 01We offer here a high quality replacement display with modern LED technology for the backlight.Color: white font/black backgroundScope of delivery:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description!Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly for LCD Display in Roland D70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", or "02". 

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inRoland D-110Electrical properties:The stereo nominal resistance has 50 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 9,5 mm, the total length without pins is 24 mm. In this total length the casing is 7 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch). Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Encoder 12 mm footprint and switch suitable for modelsRoland Fantom XRPractical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Single pole rocker switch with solder lugs suitable for modelsKorg MonoPolyKorg PolySixKorg Part Number: 375016006A / 250VACTermination Solder Lug1 poleMounting hole: 19,8 x 12,8 mmDimensions outside: 20,8 x 14,8 mmVDE-tested Mechanical Description:The switch housing consists of polycarbonate. The switch is provided for a snap-in mounting in a housing and having corresponding spring lips on the narrow side of the housing. Housing cutout for installation should be 19.30 mm x 12.90 mm. The switch itself has a width of 12.90 mm, a length of 18.50 mm and a height of 13.60 mm plus 3 mm height of the rocker. The outside dimensions are 20.8 mm x 14.8 mm.Electrical properties:The electrical components are made of copper with a silver or tin plating and electrical connection is made with solder lugs for cable assembly. The length of the terminals is 2.9 mm with a width of 3 mm.The electrical load is 6 A at 250 VAC.Knowledge in soldering is required for switch replacement.

Electrolytical Capacitor 1uF/50V SMDManufakturer: NichiconSerie: UQ for Audio Especially with SMD Elkos we often have the experience that these Elkos are often leaking after 20 years of operation and urgently need to be replaced.I offer here Elkos manufacturer Nichicon, these are used in audio, hi-fi and musical instruments.The UQ series was specially developed for use in audio technology.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

4 pcs. Slide potentiometer with 30mm travel and 15mm Lever. (Custom Build with dust cover for Synth-Parts)Suitable for Roland Juno 106        all without Bender BoardWe offer here a special version of this slider including a Dust CoverThis volume control with the labelling EWA-NK0D15B54 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 50 kOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of metall. Its height is 15 mm, the breadth is 4 mm at the top and 5 mm at the bottom. Depth is 1,2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      ARP RATE,DELAY TIMERoland Juno 60    Arpeggio RateElectrical properties:The nominal resistance has 1 MOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Keys, unweighted for Roland SK9 KeyboardThis part fits for all Roland SK9 KeyboardsRoland SK9 Keyboard is used inJP-8000Color/tint: pure white