Roland MC-909

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos     -   MIX SectionRoland MC-909Yamaha RS-7000   - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

Rotary Potentiometer vertikal 11x11 mm with center click, 10kOhmSubstitute rotary potentiometer for Roland MC-909The rotary pot fits also inKorg electribe EMX1 Korg electribe ESX1here the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. tactile switch suitable for modelsRoland MC-505Roland MC-808Roland MC-909Roland Part Number:  1343478The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

tactile switch suitable for Keypad in these Groovebox'sRoland MC-303Roland MC-307Roland MC-505Roland MC-909   TAPYamaha RS7000Part Number:Roland 125590Yamaha V5914900The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Single-pole push switch in the switch design - OFF with solder Pins for PCB mounting suitable for modelsKorg EA-1Korg EMX-1Korg ER-1Korg Part Number: 375014800technical Dates:Voltage: 250VACCurrent: 5ATermination Solder PinVDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for P.C.B. mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Encoder 12 mm suitable for modelsRoland Juno Di, Juno G, Juno GiRoland Fantom X6Roland Fantom X7Roland Fantom X8Roland MC909Roland     part number: 03122134 and 01905467Practical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Slide potentiometer with 30mm travel. Suitable forKorg M3Korg Kronos 61Korg Kronos 73Korg Kronos 88Korg      spare part No.: 500365011400Specifications:Resistance: 10 kOhmtravel: 30 mmTechnical description:The potentiometer has a sliding path of 30 mm. Praktical tip:The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slider with 45mm Travel. Suitable for  Kurzweil SP88Roland MC909 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.