Korg Kronos 61

Jalco

YKB21-5074 - Phone Jack 1/4 - 6.3 mm PCB Stereo with switch

Phone Jack 1/4 inch- 6.3 mm, stereo with switch, for printed circuit used in Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5074SCJ630P5PJ603Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Synth-Parts

Rotary Poti vertikal, 11x11 10kOhm

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos - MIX SectionRoland MC-909Yamaha RS-7000 - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Jalco

YKB21-5006 - Phone Jack 1/4- 6.3 mm for printed circuits Stereo

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 6 .88*

Jalco

Phone Jack 1/4 - 6.3 mm PCB Stereo with switch

Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 5 .81*

KORG

Rotary VR Knob for Korg KRONOS

1 pcs. Knob for rotary potentiometers inKorg Kronos 61Korg Kronos 73Korg Kronos 88ROTARY VR KNOB (KRONOS) X5870 VR KNOB(H) E30459-1 Specifications:Diameter top: 9 mmDiameter bottom: 10 mmHight: 14 mmShaft: 6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

€ 8 .34*

Panasonic

tactile switch 9,5 mm Korg

tactile switch suitable for KorgThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

KORG

Pitch Bend Assembly for Korg Pa3/4-series

1 pcs. Pitch bend Assembly for Korg Music Production WorkstationKorg KronosKorg Kronos 2Korg Pa3XKorg Pa3X ProKorg Pa4XKorg Pa4X ProKorg Pa300Korg Pa600Korg Pa700Korg Pa900Korg Pa1000This pitch bend unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all.

€ 38 .00*

Synth-Parts

Replacement stereo rotary potentiometer 14mm for Korg Kronos

Replacement stereo rotary potentiometer 14mm widht suitable forKorg KronosElectrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .45*

KORG

Korg Kronos Slider VR Knob

1 pcs. Korg Kronos Slider VR KnobKorg Kronos 61Korg Kronos 73Korg Kronos 88Korg Kronos Slider VR Knob X09130 SVR KNOB-B/G E40805-2Technical Description of Korg Kronos Slider Knob:This Slider knob will be put on slide potentiometer on your Korg Kronos Synthesizer. There is no tool needed.

€ 8 .34*

Synth-Parts

Slide potentiometer with 30mm Travel for Korg M3, Kronos

Slide potentiometer with 30mm travel. Suitable forKorg M3Korg Kronos 61Korg Kronos 73Korg Kronos 88Korg spare part No.: 500365011400Specifications:Resistance: 10 kOhmtravel: 30 mmTechnical description:The potentiometer has a sliding path of 30 mm. Praktical tip:The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

From

€ 9 .56*

KORG

Replacemet Keys, weighted forSK4 Keyboard

Key: Key A

Replacement Keys, weighted for Korg SK4 KeyboardColor: pure whiteThe Korg SK4 Keyboard is a touch-sensitive keyboard with weighted Keys.The weighted keys have a length of 15.5 cm with a width of 2.24 cm. The depth of the key is 3.5 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is from the front 10 cm. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping.

€ 11 .90*

KORG

Korg Pitch Bend Potentiometer - discontinued

1 pcs. Korg Pitch Bend PotentiometerThis is a replacement Poterntiomter for Korg Pitch Bender. This Potetniomter will fit in a realy large range of Korg Instruments.In doubt please compare spare part number with your Service Manual.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):THis Potenziometer is a very spezial part. This one will only fit for Korg Pitch Bend.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .79*

KORG

Korg Pitch Bend 2 pcs. Potentiometer with PCB- discontinued

1 Set Korg Pitch Bend Potentiometer witch PCB KLM2304 / KLM2305This is a replacement Poterntiomter for Korg Pitch Bender. This Potentiomter will fit in a realy large range of Korg Instruments.In doubt please compare spare part number with your Service Manual.This is a set of two Potentiometers for Korg Pitch Bend.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Korg Pitch Bend.Replacement for PCB KLM2304 and KLM2305Useful hint:This Potenziometer is ready mounted on the PCB. For replacement you have only to connect the cable.

€ 14 .90*

KORG

Korg Kronos Button Large

1 pcs. Button largeKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 9 .06*

KORG

Korg Kronos Button Small

1 pcs. Button SmallKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 9 .06*

KORG

Kontaktgummi SK4 Tastatur 12 Kontakte Discontinued

Rubbercontact: 12 Contacts

Contact rubber for Korg SK4 KeyboardContactrubber with 12 contacts are discontinued.Strip bright: 26 mmStrip height: 9.5 mmStrip length: 164 / 179 mmNumber of contacts: 12 or 13A rubber contact strip consists of 12 contacts and covers an octave. For the complete exchange of the contact strips in a keyboard with 61 keys 4 contact rubbers with 12 contacts and 1 contact rubber with 13 contacts are required.

€ 10 .79*

Korg Kronos 61 spare parts easy to buy online

The Korg Kronos 61 workstation is a music-workstation designed for professional use by professional and amateur musicians. If a workstation from Korg is used a lot then the individual components of the Korg Kronos 61 workstation are subject to wear. Anyone who likes to play a lot on his Korg Kronos 61 Workstation will need a key from the keyboard as a spare part at some point. But also the contact rubber or the sensorboard in the keyboard of the Korg Kronos 61 Workstation may need to be replaced by a new component. During frequent use of headphone of the Korg Kronos 61 Workstation the phone jack are stressed hard. Also power supply or the power cord are parts that can be damaged over time. If after many years of trouble-free music making you can hear crackling and popping in the speaker, then most likely the volume control is defective. With us you can easily buy a new potentiometer for your Korg Kronos 61 workstation.

We supply spare parts for Korg Kronos 61 music-workstation worldwide.

We are your reliable supplier for spare parts of your Korg Kronos 61 workstation. We offer our spare parts like phone jack socket, tact switch or volume potetniometer in our online store. We also have the matching potentiometer usually permanently in stock. Original Korg spare parts like contact rubber, key and sensorboard we also have in our assortment. Spare parts we have partly also in OEM quality for the Korg Kronos 61 workstation in stock. For us OEM quality means that we get spare parts such as tact switch, potentiometer or phone jack directly from the same supplier from which Korg buys the components. Our original Korg spare parts like sliptape, contact rubber or sensorboard are usually shipped with Deutsche Post or DHL. If the delivery of your needed spare part for the Korg Kronos 61 Workstation is especially urgent, please contact us. We can also organize an express delivery with UPS.

Filter products

Korg Kronos 61

Korg Kronos 61 spare parts easy to buy online

We supply spare parts for Korg Kronos 61 music-workstation worldwide.