Skip to main content Skip to search Skip to main navigation

Filter products

ALESIS

Synth-Parts

Average rating of 0 out of 5 stars

Alesis Andromeda Potentiometer Post Filter
1 pcs. Replacement rotary potentiometer suitable for Alesis Andromeda A6   -  Post FilterWe have set out on a search!Alesis used potentiometers manufactured by Panasonic in the Andromeda A6. Unfortunately, Panasonic has stopped the production of this potentiometer series. In addition, there is the fact that the potentiometers from Panasonic have a few special features so that most commercially available potentiometers can not be used.After a lengthy research, which unfortunately did not lead to a positive result, we decided to build a potentiometer especially for the Alesis Andromeda A6.Shaft and guide are made of metal: We deliberately chose a potentiometer with a metal shaft and guide. We are convinced that this leads to a much longer life span than the original Panasonic potentiometers where shaft and guide are made of plastic.Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 9 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 17,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:67 pcs. - to replace all small Potentiometer in your Alesis Andromeda A6 you will need 67 of these.The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

From
€ 3 .15*
Synth-Parts

Average rating of 0 out of 5 stars

Phone Jack 1/4 inch for printed circuits Mono
1 pcs. Phone Jack 1/4 inch, Mono for printed circuitSpecification:MonoThread: UNF 7/16 InchHousing: PlasticThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 1 .99*
Synth-Parts

Average rating of 0 out of 5 stars

Alesis HR-16 select Potentiometer
1 pcs. Alesis HR-16 select PotentiometerThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 8 .98*
Synth-Parts

Average rating of 0 out of 5 stars

Alesis HR-16 Volume Potentiometer
1 pcs. Alesis HR-16 Volume PotentiometerThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 8 .98*
Synth-Parts

Average rating of 0 out of 5 stars

LCD Display ALESIS Andromeda A6 black
1 pcs. black LCD Display with LED Backlight replacement for ALESIS Andromeda We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color:  white Character / black BackgroundDelivery scope:Display ready wiredMounting parts Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savvy people.Installation service:We are also happy to install the display for you. Please ask.  

€ 95 .00*
Jalco

Average rating of 0 out of 5 stars

DIN female 5 pin MIDI for printed circuits
1 pcs. MIDI DIN socket female 5 pin for printed circuitsused by: KorgRolandYamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

€ 6 .94*
Synth-Parts

Average rating of 0 out of 5 stars

tactile switch 7 mm for Alesis
1 pcs tactile switch 7 mm suitable forAlesis AndromedaWe offer here a tactile switch for Alesis that has the same technical features as the original one.The switch are soldered onto a circuit board. Manual dexterity and experience in soldering are required to replace the switches.why should I solder new pushbutton 

€ 1 .61*
Synth-Parts

Average rating of 0 out of 5 stars

Rotary Pot for LCD Contrast L=20mm
1 pcs. Rotary potentiometer for LCD Contrast adjustment  The potentiometer is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 3 .44*
Synth-Parts

Average rating of 0 out of 5 stars

LCD Display blue for ALESIS Andromeda
1 pcs. new Blue LCD Display with LED Backlight replacement forALESIS Andromeda A6We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character on Blue BackgroundAttention: The colour of the display shown may differ slightly from the original, e.g. due to your screen settings. Delivery scope:Display, prepared ready to plug inMounting partsBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping) is eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:This work should only be carried out by people who are technically, preferably electrotechnically, experienced.Installation service:We are also happy to install the display for you. Please ask.

€ 95 .00*
Synth-Parts

Average rating of 0 out of 5 stars

LCD Display white for ALESIS Andromeda
1 pcs. white LCD Display with LED Backlight replacement for ALESIS AndromedaWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color:   black Character / white BackgroundDelivery scope:Display ready wiredMounting partsBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savvy people.Installation service:We are also happy to install the display for you. Please ask.

€ 95 .00*
Synth-Parts

Average rating of 0 out of 5 stars

Alesis HR-16 OLED Display NEW
Color: Blue
1 pcs. OLED Display New forAlesis HR-16mechanical work is required on Alesis HR-16:The display is mounted on plastic bolts that are firmly connected to the housing. These plastic bolts must be shortened. The height of the OLED display is much lower than the height of the original LCD display. Without adjustment of the plastic bolts, a tunnel effect occurs because the new OLED display is much too deep in the housing.The screws from the original display can be reused.No soldering is required. The required plug is already soldered on and the cable is only plugged on.The color of the display shown may differ slightly from the original.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000  operating hours. After this specified drive time, the display still has 50% of its original luminosity.

€ 65 .00*
Varta

Average rating of 0 out of 5 stars

Batterie 1/2 AA with Solder pin
1 pcs. Lithium batterie 1/2 AA with 2 solder pin suitable for  Attention: EU shipping omlyTechnical Description:The dimensions of 1/2AA are diameter of 14,50 mm and a length of 25 mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The distance between the solder legs is 15 mm.Manufacturer: Practical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

€ 11 .45*
Synth-Parts

Average rating of 0 out of 5 stars

LCD Display yellow with cable Kit for ALESIS Andromeda
1 pcs. new Blue LCD Display with LED Backlight replacement forALESIS Andromeda A6We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character on Yellow BackgroundAttention: The colour of the display shown may differ slightly from the original, e.g. due to your screen settings.  Delivery scope:Display, prepared ready to plug inMounting partsBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping) is eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:This work should only be carried out by people who are technically, preferably electrotechnically, experienced.Installation service:We are also happy to install the display for you. Please ask.

€ 95 .00*

Order spare parts for ALESIS easily online.


Synthesizers and samplers are devices that are exposed to a continuous load and must withstand it reliably. This is true for private use, as well as for professional use. If the smallest components do not work, the entire system cannot deliver the desired first-class sound. We offer in our store ALESIS spare parts products that continue brand quality even after replacement in the usual way. This includes synthesizer spare parts and sampler spare parts, but also encoder for ALESIS, jack socket for PCB mounting or LCD display for ALESIS.All ALESIS spare parts in our store have one thing in common: they convince in material and workmanship quality. We know that when musicians are hitting the keys or technicians are doing their job, there is no time for long breakdowns. Therefore, the ALESIS spare parts are optimally compatible and can be replaced without any problems and, above all, quickly and easily. The gig or rehearsal can continue immediately afterwards. Just give us a call or send an email if you are not sure which spare part for ALESIS you should buy, or which synthesizer spare parts or sampler spare parts are the right ones for the models you use. We will be happy to advise you!

Do not compromise on quality


A system is only as powerful as its smallest component. This means for you that ALESIS spare parts should also be purchased and installed in brand quality that you know from the manufacturer. This applies to tact switch for ALESIS, as well as to the LCD display for ALESIS or any other Synthsizer spare parts. If you compromise here, you are making a big mistake. Professionalism, which you need on stage, is also essential for spare parts. No matter if you want to buy an potentiometer for ALESIS or a tact switch for ALESIS, the same professional quality is appropriate as if a device is bought completely. For all questions we are happy to help you. Jack for PCB? Symthesizer spare part? No matter what you need: We advise you competently, so that your favorite music can sound as usual again. Online ordering is quick and uncomplicated, and we are always your efficient contact partner when it comes to installing the spare parts.