Roland D-550

Jalco

YKB21-5012 - Phone Jack 1/4- 6.3 mm for printed circuits Mono

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit used in Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5012HLJ 4306HLJ 4306-01-3000Mono with switchit is used by the following manufaturesKorg partnumber: 454004300Roland partnumber: 13449146Yamaha partnumber: VB312600 YKB21-5012Yamaha partnumber: VE742000 HLJ 4306These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Jalco

YKB21-5010 - Phone Jack 1/4 - 6.3 mm PCB Stereo

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used in Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5010HLJ0520-01-010HLJ1520-01-3010HTJ-064-10Dsame PCB layout, different housingHLJ4416-01-3020it is used by the following manufaturesKorg partnumber: 454004400Roland partnumber: 13449125 HLJ0520-01-010Roland partnumber: 13449145 YKB21-5010Yamaha partnumber: VE382300Technical description Jalco YKB21-5010:The offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. This phone jack is available from various manufacturers in the same mechanical and technical construction. An exception is the manufacturer HOSIDEN using a wider housing. The electrical connection has the same structure.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .56*

SCHULZKABEL

Power cable 2 pol for Roland, 2m

Power cabel 2m with 2P plug for Roland InstrumentsVDE testedCable: H05VV-F2G0,75mm²Socket: C10Mains plug CEE 7/7 earth contactLength: 2 mAlso forKorgAkai

€ 9 .64*

Synth-Parts

Roland D-550 OLED Display new white

1 pcs. OLED Display brandnew in white forRoland D-550this is a plug in ready Display replacement for Roland D-550. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation:We deliver this OLED dislpay for the Roland D-550 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

€ 124 .00*

Varta

CR2032

1 pcs. CR2032Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Manufacturer: Panasonic or Varta Information for handling old Battery's

€ 3 .19*

ALPS

tactile switch 9,5 mm Roland

tactile switch suitable for models RolandRoland D-550Roland MKS-50Roland MKS-70Roland Spare Part Number: 13129733The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .64*

Synth-Parts

D/A-Converter PCM54HP, DIP28

1 pcs. PCM54HP - Digital-Analog-Converter for audio application von Burr BrownThis part is used inKorg M1Korg T1Korg T2Korg T3 Resolution: 16bitInterface: parallelCase: DIP28warm-up time: 1 minMechanical Description:The digital to analog converter is housed in a DIP 28 package and is designed for classic through hole mounting on a circuit board. Use of a socket is possible. The DA converter has 2 x 14 connecting pins with grid of 2.54 mm x 15.24 mm.Technical Description:This D/A converter was developed specifically for use in audio applications. The DA converter provides low distortion and typical differential linearity error is 0.001%. The interface is parallel and provides a 16 bit resolution. It is a symmetrical supply voltage of +- 5V to +- 12V needed.

€ 17 .85*

ALPS

Duo pole push switch, 250V/5A, soldering

1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for models technical Dates:Voltage: 250VACCurrent: 5ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for Cable mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

€ 7 .95*

Jalco

Roland triple female MIDI Socket, Jalco, YKF51-5046

1 pcs. triple MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. The original MIDI jack in your instrument will certainly look somewhat different. Today's possible replacement of this 3-way MIDI jack looks slightly different, but is identical in function. used by:Roland These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 10 .89*

Synth-Parts

Roland D-550 OLED Display new yellow

1 pcs. OLED Display brandnew in yellow forRoland D-550this is a plug in ready Display replacement for Roland D-550. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation:We deliver this OLED dislpay for the Roland D-550 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

€ 124 .00*

Simply order spare parts for Roland D-550 online

Synthesizers and samplers are devices that are exposed to continuous loads and must also withstand them reliably. This applies to private needs, as well as for professional use. If the smallest components do not work, the entire system can not deliver the desired first-class sound. In our shop we offer you Roalnd D-550 spare parts products, which continue the brand quality after the replacement in the usual way. These include synthesizer replacement parts and key replacement parts, but also D-550 encoders, PCB mount phone jacks or LCD display for Roland D-550. One thing all Roland spare parts have in common in our shop: they convince in material and quality of execution. We know that when musicians hit the peg or technicians do their job, there is no time for long failures. Therefore, the D-550 replacement parts are optimally compatible and can be easily and, above all, swiftly and easily emptied. The gig or rehearsal can then continue immediately. Just call or email us if you're not sure which Roland D-550 probe to buy or what type of Replacement Parts or replacement key are right for the models you use. We are happy to help!

Do not compromise on quality

A system is only as powerful as its smallest component. For you, this means that Roland brand-quality replacement parts that you know from the manufacturer should also be purchased and installed. This applies to Roland D-550 encoders as well as the Roland D-550 LCD display or any other D-550 replacement parts. Anyone who compromises here makes a big mistake. Professionalism you need on stage is also essential for replacement parts. Whether you want to buy an Roland D-550 encoder or an Roland D-550 tact switch, you have the same professional quality as buying a complete device. For all questions we are gladly there for you. Phone jack socket for PCB? Replacement keys? No matter what you need: We will advise you competently, so that your favorite music can sound as usual again. Online ordering is quick and uncomplicated, and we are always your high-performance partner for the installation of spare parts.

Filter products

Roland D-550

Simply order spare parts for Roland D-550 online

Do not compromise on quality