Friedrich-Engels-Allee 161A, 42285 Wuppertal, Germany
We 10 am - 5 pm
Fr 10 am - 2 pm
Or via our contact form.
Go to homepage
€0.00

Filter products

E-Mu Ultra Proteus

SIMM Socket 1,27mm 72P
Synth-Parts
SIMM Socket 1,27mm 72P
1 pcs. SIMM Socket 1,27mm 72PTechnical Hint:Mounting of this part requiers soldering. 

€ 14 .49*
Encoder 22 mm for E-MU Sytems
Synth-Parts
Encoder 22 mm for E-MU Sytems
1 pcs. Encoder 22 mm suitable for some E-MU Systems instrumentsE-mu ESIE-mu E4XT     depends on manufacturing dateE-mu e6400   depends on manufacturing dateE-mu e-synth ultraE-mu Proteus 1Practical advice:this encoder was used in some few E-Mu Instruments. Please have a look in your instrument first if this is the right one for you. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

€ 10 .71*
Tactile switch 15,4 mm
Synth-Parts
Tactile switch 15,4 mm
Tactile switch suitable for  The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.Why should I solder new pushbutton

€ 3 .36*
Power cable 3 pol C13-plug, 3m
Synth-Parts
Power cable 3 pol C13-plug, 3m
1 pcs. Power cabel 3m with 3P C13 plug   

€ 9 .64*
BR2330
Panasonic
BR2330
1 pcs. Lithium Battery BR-2330Attention: Shipping for Europe only Technical Description:The dimensions of BR2330 are diameter of 23 mm and a thickness of 3 mm. Manufacturer: Panasonic or Varta Information for handling old Battery's

€ 4 .78*
Power cable 3 pol C13 Socket, 1.8 m
Synth-Parts
Power cable 3 pol C13 Socket, 1.8 m
1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m

€ 6 .45*
1 pcs. Cap round for power switch
Synth-Parts
1 pcs. Cap round for power switch
 1 pcs. Cap round for power switch

€ 2 .44*
E-Mu triple female MIDI Socket for PCB, Jalco, YKF51-5046
Jalco
E-Mu triple female MIDI Socket for PCB, Jalco, YKF51-5046
1 pcs. triple MIDI DIN socket female 5 pin for printed circuit for E-MuJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. This is a 1:1 replacement for the MIDI jack in most e-mu sampler.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 10 .89*
E-Mu Ultra Proteus OLED Display NEW blue
Synth-Parts
E-Mu Ultra Proteus OLED Display NEW blue
Color: Blue
1 pcs. OLED Display New forE-Mu Ultra ProteusTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

€ 58 .99*
Cap round 12 mm for tact switch
Synth-Parts
Cap round 12 mm for tact switch
 1 pcs. Cap round 12 mm for tact switchThis cap for stylus has a diameter of 12 mm and a receptacle of 3 x 3 mm.Suitable as a spare part for E-Mu sampler

€ 3 .39*
Duo pole push switch, 250V/6A, soldering
NKK Switches
Duo pole push switch, 250V/6A, soldering
1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for modelsE-Mu  -  Mounting Frame must be taken overtechnical Dates:Voltage: 250VACCurrent: 6ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for soldering. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 15 mm, a length of 30 mm and a height of 9 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

€ 14 .93*
E-Mu Phone Jack 1/4 - 6.3 mm for printed circuits Stereo with one Switch
Nord
E-Mu Phone Jack 1/4 - 6.3 mm for printed circuits Stereo with one Switch
1 pcs. Phone Jack 1/4- 6.3 mm, stereo witch one Switch, for printed circuit used by E-mu E4KE-mu E-SynthE-Mu E4 XTE-Mu e6400Technical description:The offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 7 .84*