Yamaha CP-series

1 pcs. tactile switch suitable for Yamaha MotifOn Yamaha Motif modells these switch is for lightning buttons.These switch is also suitable forYamaha PSR9000Yamaha Tyros serie    -  without LCD BoardYamaha Part Number: VV439800,WG31840R, VQ371700The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Yamaha GH3/NL2 Stopper U88 V8468201This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards. Old spare part no is: VU34210R 

tactile switch suitable for Yamaha ModellsRS7000                        (REC/Play/Stop/<)RM1X                           (Control Buttons without Keyboard)Motif 6, Motif 7,Motif 8   (switch without LED)Motif XS, Motif ES         (switch without LED)Yamaha Part Number: VZ085500The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Yamaha GH3/NL2 Stopper L88 - lower Felt V7640101This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards. 

Replacement Keys for Yamaha GHD KeyboardThese Keys fits for all Yamaha GHD keyboards.Note on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.Yamaha GHD keyboard is used in:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200This list of Yamaha Clavinova models is only a small selection. These keys were used in many models.Hanging Keys:In a series of these keyboards there was a problem with so-called hanging keys caused by the use of an unsuitable plastic grease.The key is clicked into the keyboard frame at the rear end. Yamaha originally used white grease here. This plastic grease has attacked the plastic of the key's. In the long run, this led to a material break at the back side of the key's (see photo 2).By this material break, the key is a bit wrong and thereby strikes the key next to it, dragging and is thus difficult (hangs). Instruments affected between May 2000 and January 2003 are affected.Today Yamaha uses a blue keyboard grease which is suitable for the plastic keys. If you still find this white grease in your keyboard, it is recommended to remove this grease and replace it with the blue one. For a keyboard should be 10 to 20 grams of grease.The Yamaha GHD keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

Phone Jack 1/4 inch- 6.3 mm, stereo with switch, for printed circuit used in  Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5074SCJ630P5PJ603Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Contactrubber GH3 suitable for Yamaha This keyboard is used in these modells:Yamaha CVP-305Yamaha CVP-307And much more other Modells.For a complete Keybord with 88 keys you will need this quantity on contactrubber:1 x 5 contacts6 x 12 contacts1 x 11 contacts 

1 pcs. Yamaha GH3 Actuate RubberThis rubber fits in these keyboardsYamaha GHDYamaha GH3Yamaha NL2This rubber is used on every single key as stopperColor: black 

Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in  Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. new Contactrubber for Yamaha GHD KeyboardThis keyboard is used in these modells and others:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha CVP-207Yamaha CVP-209Yamaha CVP-401Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200Color of these Contactrubber may be different.

1 pcs. Pedal Volume PotentiometerThis is a replacement Poterntiomter for Pedal from E-Piano if there is a Volume Pedal installed.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Pedal.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. Slide potentiometer with 20mm travel. Suitable forYamaha Tyros 3    -   Assign Slider 1-8Yamaha Tyros 4    -   Assign Slider 1-8Yamaha Tyros 5    -   Assign Slider 1-8  Appearance (technical characterisation):The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. new Contactrubber for Yamaha GHL KeyboardThis keyboard is used in these modells:Yamaha P-35Yamaha P-70Yamaha P-105Yamaha AriusYamaha MOXD8Yamaha MOXF8Color of these Contactrubber may be different.

Replacement Keys for Yamaha NL2 KeyboardThese Keys fits for all Yamaha NL2 keyboards.Yamaha NL2 keyboard is used in:Yamaha CP5Note on the keys supplied:The keys are delivered without the black rubber that is mounted at the bottom of the key. The black rubber is taken from the old key. The rubber is clicked in and can be easily replaced. The Yamaha NL2 keyboard is a velocity-sensitive keyboard. The keys have a wooden core that is covered with plastic.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs tactile switch 7,3 mm for YamahaThese tact switch are soldered onto a circuit board. Manual skills and experience in soldering are required to replace the tact switch.why should I solder new pushbutton

1 pcs. Rotary Potentiometer for Modulation suitable forYamaha MotifResistance: 10 KOhm

1 pcs. Yamaha Montage Scene Rotary PotentiometerYamaha Montage 6Yamaha Montage 7Yamaha Montage 8Yamaha YC73Yamaha YC88Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Replacement stereo rotary potentiometer 14mm suitable forYamaha CLP-150Yamaha P-250Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 7,5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Contactrubber GH 2M suitable forYamaha CP1

1 pcs. brand new LCD Display with backlight suitable forYamaha CP4 Stage PianoYamaha CP40 Stage PianoWe offer here the original Yamaha spare part. Scope of delivery:1 pc. new LCD display, ready wired Notes on installation:Please be aware that you are opening an electrical device that is supplied with 230 volts. This work should only be carried out by people who have the appropriate expertise. Notes on disposal:Each electronic component contains important raw materials that should be recycled. Please find out where in your area there is a corresponding collection point for these components. 

1 pcs. Yamaha GHD CL A88 Keyboard complete This keyboard is used in these modells:Yamaha CLP-150Yamaha CLP-320Yamaha CP-40Yamaha CP-50Yamaha CP-300Color: cremewhite--- shipping only in germany, sorry  ----- 

1 pcs. Yamaha GHL Stopper L73 - lower FeltThis GHL keyboard is used in these modells and others:Yamaha P-121Only for 73 Key Keyboard.  

1 pcs. Yamaha GHL Stopper U73This GHL keyboard is used in these modells and others:Yamaha P-121Only für 73 Key Keyboard 

1 pcs Yamaha CP4,CP40 GHD connection cable 7 pol for KeyboardThis Cable connects keysboard an Mainboard in your Instrument. Please note: This cable will most likely be available in many different lengths!!!!