Roland PG serie

Synth-Parts

DC Power Jack No5 with solder pins for PCB

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland TB-303technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

€ 4 .89*

Jalco

Roland triple female MIDI Socket, Jalco, YKF51-5046

1 pcs. triple MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. The original MIDI jack in your instrument will certainly look somewhat different. Today's possible replacement of this 3-way MIDI jack looks slightly different, but is identical in function. used by:Roland These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 10 .89*

Synth-Parts

Roland PG300, PG800, JD-800 Potentiometer, Slider

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland D-70 - C1, BrightnessRoland JD-800 - Lever shorten!!!Roland PG-300Roland PG-800This Fader with the labelling EWANFX15B15 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Attention:Special pin layout. This potentiometer has a special pin layout and can only be used as a replacement for EWANFE or EWANFJ potenziometers. Not suitable for EWANA potentiometers.Without center. This potentiometer is only available without center.Electrical properties:The nominal resistance has 100 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The potetniometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 8 .45*

Synth-Parts

Roland PG-1000 OLED Display Blue NEW, LCD Replacement

1 pcs. Roland PG-1000 OLED Display Blue NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity.

€ 83 .99*

Synth-Parts

Roland PG-1000 OLED Display Yellow NEW, LCD Replacement

1 pcs. Roland PG-1000 OLED Display Yellow NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity.

€ 83 .99*

Synth-Parts

Roland PG-1000 OLED Display white NEW, LCD Replacement

1 pcs. Roland PG-1000 OLED Display white NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity.

€ 83 .99*

Synth-Parts

Roland PG-1000 OLED Display green NEW, LCD Replacement

1 pcs. Roland PG-1000 OLED Display green NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity.

€ 83 .99*

Synth-Parts

Roland PG-1000 OLED Display Red NEW, LCD Replacement

1 pcs. Roland PG-1000 OLED Display Red NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity.

€ 83 .99*

Filter products

Roland PG serie