Roland JV-Serie

Panasonic

tactile switch 5 mm for Roland

1 pcs. tactile switch suitable for models RolandFP1, FP2, FP3, FP4, FP5, FP6, FP7, FP8, FP-50JV25, JV30, JV35, JV50, JV80, JV90, JV880, JV1080JP8000JD800 - Cursor ButtonsMC-303, MC-307RD-500XP10, XP50, XP60, XP80XV3080U20Fantom X6,X7,X8 without REC/PLAY/STOPOnly for non-illuminated buttons:A90, A90-EXXP30JV1000JP8080RD-600,RD-700Roland Part Number: 13169697 or 13169752The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

Synth-Parts

Roland D10,D20,D50 Volume Slidepotentiometer - EWANA0X10B14

Stereo slide potentiometer with 30mm travel and 10mm Lever. Suitable Slider forVolume Control forRoland D10Roland D20Roland D50This Lever is a little bit thinner than the original one. Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 7 .74*

Synth-Parts

Volume Potentiometer Roland Juno 1,2 JV-80,90

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland Juno 1 VolumeRoland Juno 2 VolumeRoland JV-80 Volumen,Presence,C1Roland JV-90 Volumen,Presence,C1Roland RD-250s VolumeRoland RD-300s VolumeThis volume control with the labelling EWANA0X15B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .33*

Jalco

Roland triple female MIDI Socket for PCB, Jalco, YKF51-5046

1 pcs. triple MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. This is a 1:1 replacement for the MIDI jack in newer Roland instruments.used by:Roland These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 10 .89*

NKK Switches

Single pole rocker switch 250V/6A with solder lugs

Single pole rocker switch with solder lugs suitable for modelsRoland6A / 250VACTermination Solder Lug1 poleMounting hole: 19,8 x 12,8 mmDimensions outside: 20,8 x 14,8 mmVDE-tested Mechanical Description:The switch housing consists of polycarbonate. The switch is provided for a snap-in mounting in a housing and having corresponding spring lips on the narrow side of the housing. Housing cutout for installation should be 19.30 mm x 12.90 mm. The switch itself has a width of 12.90 mm, a length of 18.50 mm and a height of 13.60 mm plus 3 mm height of the rocker. The outside dimensions are 20.8 mm x 14.8 mm.Electrical properties:The electrical components are made of copper with a silver or tin plating and electrical connection is made with solder lugs for cable assembly. The length of the terminals is 2.9 mm with a width of 3 mm.The electrical load is 6 A at 250 VAC.Knowledge in soldering is required for switch replacement.

€ 4 .76*

ALPS

tactile switch, green LED 7 mm

tactile switch with green LED suitable for modelsRoland JV-1000 only Patch-GroupPart No.: 13119708This switch fits also for this:Roland JV-1000 Edit/Track difference: orange LEDThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 4 .50*

ALPS

tactile switch 4,3 mm Roland

tactile switch suitable for modelsRoland D5Roland D10Roland U220Part no: 13169684The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

Roland

Contactubber for Roland SK8 Keyboard

Rubbercontact: 12 Contacts

Contactrubber for Roland SK8 KeyboardRoland SK8 Keyboard is used inRoland JV-90Roland JX-30Roland JX-35Roland JX-50Roland XP-30Roland XP-50Roland XP-60Attention: This blue contactubber do not fit in old SK8 Keyboards

€ 12 .50*

Roland

Replacement keys, weighted, new for Roland SK8 Synthesizer Keyboard

Key: Key A

NEW Replacement Keys, weighted for Roland SK8 Synthesizer Keyboardused inRoland XP-30Roalnd XP-80This are new Key's without "Red Glue-Problem"

€ 12 .90*

Hosiden

Roland Phone Jack 1/4 - 6.3 mm for printed circuits Mono with switch

1 pcs. Roland Phone Jack 1/4 inch- 6.3 mm, mono with switch, for printed circuitHosiden HLJ7101-01-3010 This phone jack is no longer manufactured and there are only remaining stocks.This part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Please have a very detailed view on the picture. There is one Phone Jack very similar.Technical descriptionThe offered phone jack for PCB mounting is a Mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 7 .25*

ALPS

Roland JV-Series Parameter Slider

1 pcs. Roland JV-Series Parameter SliderRoland JV-80Roland JV-90Roland JV-1000Note on mounting the parameter slider in Roland JV series:The slider pin is thinner than on the original potentiometer. In order for the cap to hold, something has to be clamped in between the corners of the cap. For example a piece of paper.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 11 .45*

Filter products

Roland JV-Serie