Power Supply

Power cabel 2m with 2P plug for Roland InstrumentsVDE testedCable: H05VV-F2G0,75mm²Socket: C10Mains plug CEE 7/7 earth contactLength: 2 mAlso forKorgAkai 

1 pcs. SMK LGP6531-0800F DC Power Jack with solder pins for PCBtechnical Dates of LGP6531-0800F:Termination Solder PinOuter Diameter: 5.9 mmInner Diameter: 3 mmInner Contact: 1.05 mmDC-Socket LGP6531-0800F and LGP6531-1500f are nearly same. LGP6531-0800f is a little bit better with electrical contact.Mechanical Description of LGP6531-0800F and LGP6531-1500F:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 14 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

1 pcs. Cap rectangular for power switchPlease note the dimensions. The original caps used to be larger on many instruments. Dimensions: 12 x 7 mmHight: 10 mm

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsKawai ES4Kawai ES6Kawai ES7Kawai ES8Kawai ES520This part comes directly from Kawai Europe.technical Dates:Termination Solder PinOuter Diameter: 7 mmInner diameter: 3.5 mmInnercontact: 1.5 mmMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 18 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsKorg ESX-1 SDtechnical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs 65W internal Switching Power Supply Unit brand new, suitable forE-mu E4KE-mu E-SYNTHE-mu E6400E-mu E4 PlatinumE-mu E5000 UltraE-mu E6400 UltraE-mu E4XT UltraDescription:This switching power supply is a perfect replacement for many E-mu devices. In many devices Emu has used the same power supply unit.Our brand new replacement switching power supply has exactly the same mechanical dimensions and the same connectors as the original power supply. Plug and Play.63 Watt power upgrade: The original E-Mu power supply has an output of 43 Watt and must be operated with an internal fan in any case. If extensions such as additional memory or additional drives are installed, the original power supply unit will not be able to supply this power. This is where a power supply upgrade comes in handy.Our 65 Watt power supply unit also needs a fan when the E-Mu is fully extended. Electrical properties:Primary input voltage: 90 - 264 VACRated Power: 63 WattEfficiency: 77%Ripple: 1%Tripple OutputShort circuit protectionEN6100 proofEMC: CLASS BPractical advice:Plug of the device. Don't work under Voltage.Make absolutely sure that the connection cables to the power supply have no contact with the cooling element of the power supply. Due to the development of heat, the insulation of the cable can melt and cause a short circuit or worse tripping. 

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha DGX-660Yamaha P-45technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. HEC2305-016250 DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland EP7 IItechnical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Plug suitable for modelsKorg electribetechnical Dates:Termination SolderingMechanical Description:The housing of the Power Plug is made of Plastic and cable is soldered on it.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Single-pole push switch in the switch design - OFF with solder Pins for PCB mounting suitable for modelsKorg EA-1Korg EMX-1Korg ER-1Korg Part Number: 375014800technical Dates:Voltage: 250VACCurrent: 5ATermination Solder PinVDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for P.C.B. mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha PSR-S950Yamaha P-155technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha Motif RackYamaha P-120technical Dates:Termination Solder Pinouter Diameter: 7,3 mmInner diameter: 2,9 mm Mechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 3 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsKawai ES100Kawai ES110Kawai ES120Kawai VPC1This part comes directly from Kawai Europe.technical Dates:Termination Solder PinOuter Diameter: 5,9 mminner Diameter: 1 mmMechanical Description:The DC jack housing is made of plastic and the power jack is designed for direct board mounting.Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. 

1 pcs. HEC470-01-630 DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha P-85Yamaha P-140We offer the original Hosiden power socket here.technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Kawai Power Buttonblack  for CA/CN Modells Technical Description of Kawai Button:This Button fits for many Kawai Pianos and is build for a Casing Window of 17 x 11 mm. This part has one Button. It is used with Powerswitch with plungers.Practical tip:This button is simply clipped on 

Power cabel 2m with 2P plug for AKAI InstrumentsVDE testedCable: H05VV-F2G0,75mm²Socket: C10Mains plug CEE 7/7 earth contactLength: 2 m  

1 pcs. Power cabel 1,8 m with 2P plug for Europe  

1 pcs. HEC470-01-630 DC Power Jack with solder Pins for PCB mounting We offer the original Hosiden power socket here.technical Dates:Termination Solder PinOuter Diameter: 6.5 mmInner Diameter: 2 mmMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 3 A at 16 VDC. Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.  

1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for models technical Dates:Voltage: 250VACCurrent: 5ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for Cable mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland TB-303technical Dates:Termination Solder PinSchwitch: OpenMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for this replacement.

1 pcs. Yamaha FUSTB AC-IN BoardFor Europe only: 230VACUsed inYamaha CLP-575 

1 pcs. SMK LGP7031-1200F DC Power Jack 3.5 mm with solder pinstechnical Dates of LGP7031-1200F:Termination Solder PinOuter Diameter: 7 mmInner Diameter: 3,5 mmInner Contact 1.5 mmSwitch: openMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 18 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs 45W internal Switching Power Supply Unit suitable forKorg SV1Electrical properties:Primary input voltage: 90 - 264 VACRated Power: 45 WattEfficiency: 77%Ripple: 1%Tripple OutputShort circuit protectionEN6100 proofEMC: CLASS BPractical advice:Plug of the device. Don't work under Voltage.