Nord Stage

Contact rubber for Fatar KeyboardsFatar uses in many different keyboards same contact rubber. The here offered contact rubber are suitable for!!!!!   Not for use in Roland Instruments    !!!!!Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP/10 MDRFatar TP/10 ABSFatar TP/40Fatar TP/100LRtechnichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greyFatar Keyboards are used by Clavia Nord, Döpfer, Ensonic, Korg, Kurzweil, GEM

1 pcs. Clavia Nord Volume Dreh Potentiometer Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 16 mm Diameter, the total length without pins is 32 mm. In this total length the casing is 9 mm long. On this casing is the thread with 7 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 4 mm and is flattened on a length of 12 mm. It is made of metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. Screw 16 mm Black PhillipsLength: 16 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one is used for red side panels.

1 pcs. Screw 6 mm Black PhillipsLength: 6 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one can be located on rear side or on bottom.

1 pcs. Nord Pedal Spring  

1 pcs. Clavia Nord Knob with line  4 mmThis control knob fits on a 4 mm D-axis. Nord used these knobs on older models. Especially for the volume potentiometer.Praktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs. Clavia Nord Knob Praktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs. Nord Encoder 22 mm for Nord Stage 2 with DetentOriginal Nord spare part. Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Encoder 22 mm without Detent.Also suitable for:Nord Modular G2  - Secondary Dial Master Clock -> Patch LevelPractical adviceThe encoders offered here come from the same manufacturer as those used by Nord. There are small deviations in design compared to the original:Pin distance here is 2.5 mm compared to 5 mm for the originalOriginal encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases at Nord and can be removed. These encoder are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs.Clavia Nord LCD Display new white Replacement LCD Display for Claiva Nord Instruments. For installation soldering is requiered.Notes on installation for Nord LCD Display:This LCD Display is soldered to a PCB only with a small connector. This requieres very good soldering knowlege. Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 20,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.  

1 pcs Clavia Nord PSU Transformer 22770 Electrical properties of 22770:Primary: 230 V AC or 2 x 115 V ACSec: 4 x 7,5 Volttransformer for PCB mountingPractical advice:Plug of the device. Don't work under Voltage. 

1 pcs. Encoder 22 mm suitable forNord NordStage 2  - Main DialPractical advice:The encoders offered here come from the same manufacturer as those used by Nord. There are compared to the original small deviations in design:Pin distance here is 2.5 mm compared to 5 mm for the originalOriginal encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases at Nord and can be removed. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Clavia Nord cape for Encoder older modells Praktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs. Clavia Nord Knob Encoder older modells Praktical tip:The knobs are just plugged on. No tools are needed.