1 pcs. Yamaha GH3/NL2 Stopper U88 V8468201This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards. Old spare part no is: VU34210RÂ
1 pcs. tactile switch suitable for Yamaha MotifOn Yamaha Motif modells these switch is for lightning buttons.These switch is also suitable forYamaha PSR9000Yamaha Tyros serie  - without LCD BoardYamaha Part Number: VV439800,WG31840R, VQ371700The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Yamaha GH3/NL2 Stopper L88 - lower Felt V7640101This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards.Â
Replacement Keys for Yamaha GHD KeyboardThese Keys fits for all Yamaha GHD keyboards.Note on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.Yamaha GHD keyboard is used in:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200This list of Yamaha Clavinova models is only a small selection. These keys were used in many models.Hanging Keys:In a series of these keyboards there was a problem with so-called hanging keys caused by the use of an unsuitable plastic grease.The key is clicked into the keyboard frame at the rear end. Yamaha originally used white grease here. This plastic grease has attacked the plastic of the key's. In the long run, this led to a material break at the back side of the key's (see photo 2).By this material break, the key is a bit wrong and thereby strikes the key next to it, dragging and is thus difficult (hangs). Instruments affected between May 2000 and January 2003 are affected.Today Yamaha uses a blue keyboard grease which is suitable for the plastic keys. If you still find this white grease in your keyboard, it is recommended to remove this grease and replace it with the blue one. For a keyboard should be 10 to 20 grams of grease.The Yamaha GHD keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.
1 pcs. Yamaha GH3 Actuate RubberThis rubber fits in these keyboardsYamaha GHDYamaha GH3Yamaha NL2This rubber is used on every single key as stopperColor:Â blackÂ
1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
Yamaha Spezial Keyboard grease, Blue 50gOriginal Yamaha plastic grease for Keyboards. Color is blue and will be delivered in a 50 gramm portion.Molycote G-1066YThis grease is used on YamahaOn GHD and GH3 keyboards on the fulcrum - Where the key engages the frame.For pedals at the mechanical moving parts.Â
1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha P85Yamaha P120Yamaha P140Â The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha Motif RackYamaha P-120technical Dates:Termination Solder Pinouter Diameter: 7,3 mmInner diameter: 2,9 mm Mechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 3 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.
Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
One Octave white Replacement Keys for Yamaha GHD KeyboardThis set contains:1 x A1 x B1 x C1 x D1 x E1 x F1 x GNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.Â
1 pcs. new Contactrubber for Yamaha GHDÂ KeyboardThis keyboard is used in these modells and others:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha CVP-207Yamaha CVP-209Yamaha CVP-401Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200Color of these Contactrubber may be different.
1 pcs. Yamaha GHD A88 Keyboard complete--- shipping only in germany, sorry -----Please ask if this keyboard is the right one for your e-piano model.This keyboard was used for many years in the vast majority of Yamaha electric piano models.The replacement of the entire keyboard is from a certain age of the electric piano well worth considering.For example, if your original keyboard is affected by the grease problem, you have here an alternative after desen exchange you no longer have to worry about the keyboard.If the keyboard is not in stock, we can order the keyboard from Yamaha. There may be a delivery time.
1 pcs. Flash ROM 16Mas replacement for MBM29LV160BE90TN Mechanical Description:This flash rom is housed in a TSOP48 package and is designed for SMD mounting on a circuit board. This part sensitive to static charge Â
1 pcs external Power Supply Unit Yamaha PA-300CÂ Mechanical Description:The primary plug is designed for Europe and the plug on the secondary side is round with 6.5 mm outside diameter.Electrical properties:Practical advice:Plug of the device. Don't work under Voltage.Â
Replacement Hammer for Yamaha GHD Keyboard The Yamaha GHD Keyboard is used in two different configurations.The Keyboard is availabel with a 1 zone Hammeraction and with a 4 Zone Hammeraction.Here you will find the different Hammer for the GHD Keyboard
1 pcs. Replacement stereo rotary potentiometer 14mm suitable forYamaha CLP-150Yamaha P-250Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 7,5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5050Â These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Â
1 pcs. Mainboard for Yamaha P-250 repairing E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.Â