Yamaha Montage series

1 pcs. tactile switch suitable for Yamaha MotifOn Yamaha Motif modells these switch is for lightning buttons.These switch is also suitable forYamaha PSR9000Yamaha Tyros serie    -  without LCD BoardYamaha Part Number: VV439800,WG31840R, VQ371700The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Yamaha GH3/NL2 Stopper L88 - lower Felt V7640101This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards. 

Replacement Keys for Yamaha GHD KeyboardThese Keys fits for all Yamaha GHD keyboards.Note on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.Yamaha GHD keyboard is used in:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200This list of Yamaha Clavinova models is only a small selection. These keys were used in many models.Hanging Keys:In a series of these keyboards there was a problem with so-called hanging keys caused by the use of an unsuitable plastic grease.The key is clicked into the keyboard frame at the rear end. Yamaha originally used white grease here. This plastic grease has attacked the plastic of the key's. In the long run, this led to a material break at the back side of the key's (see photo 2).By this material break, the key is a bit wrong and thereby strikes the key next to it, dragging and is thus difficult (hangs). Instruments affected between May 2000 and January 2003 are affected.Today Yamaha uses a blue keyboard grease which is suitable for the plastic keys. If you still find this white grease in your keyboard, it is recommended to remove this grease and replace it with the blue one. For a keyboard should be 10 to 20 grams of grease.The Yamaha GHD keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Yamaha GH3 Actuate RubberThis rubber fits in these keyboardsYamaha GHDYamaha GH3Yamaha NL2This rubber is used on every single key as stopperColor: black 

Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in  Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Wheighted Key's suitable for Yamaha FSX KeyboardThis keyboard is used in these modells:Yamaha Motif XS6Yamaha Motif XS7Yamaha Tyros 2Yamaha Tyros 3Yamaha Tyros 4Color: whiteThis key is new

1 pcs. Yamaha Montage Super Knob Rotary PotentiometerYamaha Montage 6Yamaha Montage 7Yamaha Montage 8Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. new Contactrubber for Yamaha GHD KeyboardThis keyboard is used in these modells and others:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha CVP-207Yamaha CVP-209Yamaha CVP-401Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200Color of these Contactrubber may be different.

1 pcs. Slider with 45mm Travel. Suitable for Yamaha Motif ESYamaha Montage 6 Main VolumeYamaha Montage 7 Main VolumeYamaha Montage 8 Main VolumeThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Encoder 16 mm widht suitable forYamaha Tyros 1Yamaha Tyros 2Yamaha CVP-207Yamaha CVP-209 Part numbers:Yamaha      VU48130R  REB161-PVB  

1 pcs. Yamaha FSX Stopper U 61This FSX keyboard is used in these modells and others:Yamaha Motif XS6Yamaha Tyros 2Yamaha Tyros 3Yamaha Tyros 4   

1 pcs. triple MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5046Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. used by:YamahaThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Yamaha Montage Scene Rotary PotentiometerYamaha Montage 6Yamaha Montage 7Yamaha Montage 8Yamaha YC73Yamaha YC88Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Yamaha FSX Stopper U 76This FSX keyboard is used in these modells and others:Yamaha Motif XS7 

1 pcs. Yamaha GH3 Stopper U88 with AftertouchThis GH3 keyboard is used in these modells and others:Yamaha Montage 8This felt is special for GH3 Keyboards with Aftertouch