1 pcs. tactile switch suitable for Yamaha MotifOn Yamaha Motif modells these switch is for lightning buttons.These switch is also suitable forYamaha PSR9000Yamaha Tyros serie  - without LCD BoardYamaha Part Number: VV439800,WG31840R, VQ371700The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. Yamaha GH3/NL2 Stopper U88 V8468201This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards. Old spare part no is: VU34210RÂ
1 pcs. Yamaha GH3/NL2 Stopper L88 - lower Felt V7640101This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards.Â
Replacement Keys for Yamaha GHD KeyboardThese Keys fits for all Yamaha GHD keyboards.Note on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.Yamaha GHD keyboard is used in:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200This list of Yamaha Clavinova models is only a small selection. These keys were used in many models.Hanging Keys:In a series of these keyboards there was a problem with so-called hanging keys caused by the use of an unsuitable plastic grease.The key is clicked into the keyboard frame at the rear end. Yamaha originally used white grease here. This plastic grease has attacked the plastic of the key's. In the long run, this led to a material break at the back side of the key's (see photo 2).By this material break, the key is a bit wrong and thereby strikes the key next to it, dragging and is thus difficult (hangs). Instruments affected between May 2000 and January 2003 are affected.Today Yamaha uses a blue keyboard grease which is suitable for the plastic keys. If you still find this white grease in your keyboard, it is recommended to remove this grease and replace it with the blue one. For a keyboard should be 10 to 20 grams of grease.The Yamaha GHD keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.
1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
1 pcs. Yamaha GH3 Actuate RubberThis rubber fits in these keyboardsYamaha GHDYamaha GH3Yamaha NL2This rubber is used on every single key as stopperColor:Â blackÂ
Yamaha Spezial Keyboard grease, Blue 50gOriginal Yamaha plastic grease for Keyboards. Color is blue and will be delivered in a 50 gramm portion.Molycote G-1066YThis grease is used on YamahaOn GHD and GH3 keyboards on the fulcrum - Where the key engages the frame.For pedals at the mechanical moving parts.Â
1 pcs. Phone Jack 1/4 inch - 6.3 mm, Mono witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5076HLJ-2305-01-3030These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
1 pcs. FFC cable for Yamaha CVP-209 500 mm length Length = 500 mmPitch= 0,5 mmBoth sides have the same connectorThis cable is used to connect LCD Display with Mainboard inYamaha CVP-207Yamaha CVP-209Yamaha CVP-900The LCD display in the Yamaha Clavinova has vertical stripes in the display?Do you have vertical stripes in the LCD display of your electric piano? These are lines that run from top to bottom through the display and do not belong in the picture.An exchange of this FFC cable can achieve an improvement. In the best case, the vertical stripes are then completely gone.Â
1 pcs. Yamaha Pedalcable No6This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. All 6 wires are assigned on both sides.This cable is used in:Â
1 pcs. new Contactrubber for Yamaha GHDÂ KeyboardThis keyboard is used in these modells and others:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha CVP-207Yamaha CVP-209Yamaha CVP-401Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200Color of these Contactrubber may be different.
1 pcs. Yamaha Spezial Keyboard grease, white 50gMOLYKOTE G-1006YOriginal Yamaha plastic grease for NL2 Keyboards.Color is white and will be delivered in a 50 gramm portion.This grease can also be used on Yamaha GHD / GH3 keyboards at key guides.
One Octave white Replacement Keys for Yamaha GHD KeyboardThis set contains:1 x A1 x B1 x C1 x D1 x E1 x F1 x GNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.Â
1 pcs. Yamaha GHD A88 Keyboard complete--- shipping only in germany, sorry -----Please ask if this keyboard is the right one for your e-piano model.This keyboard was used for many years in the vast majority of Yamaha electric piano models.The replacement of the entire keyboard is from a certain age of the electric piano well worth considering.For example, if your original keyboard is affected by the grease problem, you have here an alternative after desen exchange you no longer have to worry about the keyboard.If the keyboard is not in stock, we can order the keyboard from Yamaha. There may be a delivery time.
1 pcs. Mainboard for Yamaha CVP-209 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.Â
1 pcs. Rotary Potentiometer suitable forYamaha CVP-203Yamaha CVP-205Yamaha CVP-207Yamaha CVP-209 Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 14 x 11 mm, the total length without pins is 15 mm. In this total length the casing is 6 mm long. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of brass. Its head has ends in corner radius.The nine solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2 mm. The pins, which are sticking out are necessary for the electrical function. Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. brand new 10 inch extern LCD Display for Yamaha CVP seriesYamaha has been using color displays of various sizes in the Clavinova CVP models for many years. Displays are subject to natural aging, which leads to the fact that the displays are increasingly difficult to read. Even a readjustment of the contrast is no longer sufficient at some point. Yamaha has a very good spare parts supply for the Clavinova series. However, Yamaha cannot supply the original displays as replacements in all cases.We offer here an external HD LCD display that connects to the external video out of your Yamaha Clavinova CVP model. This ecternel Display shows same screen information as internal Display.The display resolution must be adjusted in many cases from 4:3 to 16:9 so the new display may be slightly blurred.Not an original spare part from Yamaha.Scope of delivery for extern Yamaha Clavinova LCD:1 pc. new LCD display, stand and cable for EUÂ Attention: The color of the display shown may differ slightly from the original. Â Notes on disposal:Each electronic component contains important raw materials that should be recycled. Please find out where in your area there is a corresponding collection point for these components.Â
1 piece Yamaha Pedal PCB X0193 for E-Pianos V7675600This PCB for Yamaha pedal unit is used in pedals in which three potentiometers are installed.For final use, parts on the board still have to be broken off. The break edges are marked and perforated accordingly. This can be done easily and without tools.Â