Potentiometer

Synth-Parts

Alesis Andromeda Potentiometer Post Filter

1 pcs. Replacement rotary potentiometer suitable for Alesis Andromeda A6 - Post FilterWe have set out on a search!Alesis used potentiometers manufactured by Panasonic in the Andromeda A6. Unfortunately, Panasonic has stopped the production of this potentiometer series. In addition, there is the fact that the potentiometers from Panasonic have a few special features so that most commercially available potentiometers can not be used.After a lengthy research, which unfortunately did not lead to a positive result, we decided to build a potentiometer especially for the Alesis Andromeda A6.Shaft and guide are made of metal: We deliberately chose a potentiometer with a metal shaft and guide. We are convinced that this leads to a much longer life span than the original Panasonic potentiometers where shaft and guide are made of plastic.Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 9 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 17,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:67 pcs. - to replace all small Potentiometer in your Alesis Andromeda A6 you will need 67 of these.The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 3 .75*

Nord

Clavia Nord Volume Dreh Potentiometer

1 pcs. Clavia Nord Volume Dreh Potentiometer Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 16 mm Diameter, the total length without pins is 32 mm. In this total length the casing is 9 mm long. On this casing is the thread with 7 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 4 mm and is flattened on a length of 12 mm. It is made of metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 15 .90*

Synth-Parts

Slidepotentiometer für Roland Juno 106 - EWA-NK0D15B54

1 pcs. Slide potentiometer with 30mm travel and 15mm Lever. (Custom built with dust cover for Synth-Parts)Suitable for Roland Juno 106 all without Bender Board This volume control with the labelling EWA-NK0D15B54 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part. Electrical properties: The stereo nominal resistance has 50 kOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt. Appearance (technical characterisation): This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of metall. Its height is 15 mm, the breadth is 4 mm at the top and 5 mm at the bottom. Depth is 1,2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically. Useful hint: The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 7 .98*

Synth-Parts

Rotary Poti vertikal, 11x11 10kOhm

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos - MIX SectionRoland MC-909Yamaha RS-7000 - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Synth-Parts

Rotary Poti vertikal, 11x11 10kOhm center click

Rotary Potentiometer vertikal 11x11 mm with center click, 10kOhmSubstitute rotary potentiometer for Roland MC-909The rotary pot fits also inKorg electribe EMX1 Korg electribe ESX1here the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Synth-Parts

Replacement stereo rotary potentiometer for Roland Fantom X-series, volume control EVJY10FB6A24

1 pcs. Replacement stereo rotary potentiometer for Roland Fantom X-series, suitable for volume control and ext. Level - EVJY10FB6A24Roland Fantom SRoland Fantom FARoland Fantom X6Roland Fantom X7Roland Fantom X8Roland RD-64This volume control is no longer available at the original equipment manufacturer Roland, because Panasonic, the producer of the pot, does not longer produce the production-model. The here shown replacement pot is identical in construction and 100% compatible with the original Roland part volume EVJY10FB6A24.Electrical properties:The stereo nominal resistance has 20 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 x 12 mm, the total length without pins is 22,5 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 10 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 13,8 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .49*

ALPS

Value Slider 30mm Travel for Korg

1 pcs. Mono Slider with 30mm Travel. Suitable for Value Slider for KorgN1, N5, N5ex, N264, N36401W, 01WFDX2, X3, X5, X5dM1, M1r, M3rT1, T2, T3WS, WSEXKorg spare part No.: 365007800The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 11 .45*

Synth-Parts

Roland D10,D20,D50 Volume Slidepotentiometer - EWANA0X10B14

Stereo slide potentiometer with 30mm travel and 10mm Lever. Suitable Slider forVolume Control forRoland D10Roland D20Roland D50This Lever is a little bit thinner than the original one. Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 7 .98*

Synth-Parts

Volume Slidepotentiometer Casio 30mm Travel

1 pcs. slide Potentiometer forCasio CZ-1 VolumeCasio CZ-1000 VolumeCasio CZ-3000 VolumeCasio CZ-5000 VolumeThe Lever on original Potentiometer is shorter. You can cut this Lever to the right length.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .33*

ALPS

Yamaha Stereo Potentiometer P85,, P120, P140

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha P85Yamaha P120Yamaha P140 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 9 .45*

Synth-Parts

Yamaha DX-Serie Volume Slide potentiometer - EWA-NFOC

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable for Yamaha DX7Yamaha DX9Yamaha DX11Yamaha DX21Yamaha DX27Yamaha DX100 This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 7 .98*

Synth-Parts

16 pcs. Slidepotentiometer für Roland Juno 106 - EWA-NK0D15B54

16 pcs. Slide potentiometer with 30mm travel and 15mm Lever. (Custom Built with dust cover for Synth-Parts)Suitable forRoland Juno 106 all without Bender BoardWe offer here a special version of this slider including a Dust CoverThis volume control with the labelling EWA-NK0D15B54 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 50 kOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of metall. Its height is 15 mm, the breadth is 4 mm at the top and 5 mm at the bottom. Depth is 1,2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 89 .25*

Yamaha

Yamaha Pedal Potentiometer

1 pcs. Yamaha Pedal PotentiometerThis is a replacement Poterntiomter for Pedal from E-Piano if there is a Volume Pedal installed.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Pedal.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 9 .89*

Synth-Parts

Korg EMX1 stereo Potentiometer 12 mm

1 pcs. Replacement stereo rotary potentiometer 12mm widht suitable forKorg EMX1Korg ESX1Not a 1:1 spare part. The original potentiometer is threaded. Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The six solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .99*

Yamaha

Yamaha Potentiometer for Pitch Bend

1 pcs. Rotary Potentiometer for pitch bend suitable forYamahaResistance: 10 KOhm

€ 13 .78*

Synth-Parts

Yamaha CS-15,CS-30,CS-40 Slidepotentiometer NEW B10K

1 pcs. new Slide potentiometer with 30mm travel and 15mm Lever. Suitable Slider for Yamaha CS-15 - EG-SYamaha CS-30 - EG1, EG2, EG3Yamaha CS-40 - Sustain Electrical properties:The nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint:The Lever of the original potentiometer has a conical, tapering shape.

€ 12 .48*

Synth-Parts

Roland E-Series Slidepotentiometer

Stereo slide potentiometer with 30mm travel and 10mm Lever. Suitable Slider forVolume Control forRoland E10, E15, E16, E30, E35, E36, E38, E40, E56, E70Roland KR100 Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 7 .98*

Synth-Parts

Volume Potentiometer Roland Juno 1,2 JV-80,90

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland Juno 1 VolumeRoland Juno 2 VolumeRoland JV-80 Volumen,Presence,C1Roland JV-90 Volumen,Presence,C1Roland RD-250s VolumeRoland RD-300s VolumeThis volume control with the labelling EWANA0X15B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .33*

ALPS

Roland SH-101 Potentiometer 1MA, 30mm Travel

1 pcs. Slide Potentiometer with 30mm Travel. (Custom Built with dust cover for Synth-Parts)Suitable for forRoland JX-3PRoland SH-101 Env Attack, Decay, ReleaseThese potenziometer are brand new ALPS Potentiometer. Additional benefit is a dust cover diectly mounted on housing.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 9 .75*

Synth-Parts

Rotary potentiometer,center Click for Roland MC-505

1 pcs. Replacement rotary potentiometer with center click suitable forRoland MC-303 LFO DepthRoland MC-505Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .89*

ALPS

Roland juno 106 Bender Slide potentiometer

1 pcs. Slide potentiometer with 20mm travel. Suitable forSchiebepotentiometer Juno 106 - BenderAppearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements.The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 10 .89*

Synth-Parts

Potentiometer for Yamaha rm1x with center Tap 12mm

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionYamaha RM1x Utility Mounting instruction Yamaha RM1x:The potentiometer with thread I offer here can also be used in the RM1x. The great advantage of this solution is that I think potentiometers with threads will have much longer lifetime than potentiometers without threads. Indisputably, the axis is guided and stored much more stably by the thread.n the pictures you see a test installation I have made.Electrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Synth-Parts

Replacement stereo rotary potentiometer for Korg

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inKorg Volca Sample 2Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 6 .60*

Synth-Parts

Korg EMX-1 Slidepotentiometer for Arpeggiator

1 pcs. slide potentiometer with 45mm travel without center clickKorg EMX-1 ArpeggiatorAttention: Without Center clickElectrical properties:The stereo nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation): The slide potentiometer has a travel of 45 mm. Its metallic casing measures 60 x 8 mm, the height without lever is 7 mm. The lever is made of metall and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 1,2 mm. The solder contact pins are 0,8 mm wide (one of them).In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The value control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 13 .09*

Spare parts: Rotary and slider controls, potentiometers.

Rotary and slider controls are among the most commonly used control units on synthesizers, keyboards, organs, electric pianos, samplers, drm computers, and mixing consoles. If they are worn out, the device in which they were installed is often no longer fully usable.
In many cases, such devices end up in the closet, a few months later in the basement, years later, after moisture and dirt have attacked them, in the electronic scrap. This is usually completely unnecessary, because worn or damaged potentiometers can nowadays be replaced in most cases with relatively little effort and at low cost. Often it is only necessary to find the suitable spare part. Here Synth-parts.com is your competent partner and reliable helper. Especially in the case of components discontinued by the manufacturers, we are the help you need. In more than 10 cases we have even reissued controllers that are no longer available. For this purpose, we use the original manufacturers such as Alps, in order to guarantee exact component equality.

The exchange of potentiometers

The exchange of such a component requires of course experience in the handling of appropriate tools, i.e. a soldering iron, but can also be carried out by laymen. However, it must be taken into account that the device in question must often be almost completely disassembled and then reassembled. A camera or cell phone with photo function is an indispensable aid.

Repair in our specialized workshop

If you do not dare to repair the device yourself, or if you want to avoid the effort involved, we naturally offer you the repair in our well-equipped specialist workshop. With our special measuring devices and tools, our well-trained specialists can carry out such work properly and professionally at specially equipped workstations. You can send in your device after previous appointment arrangement, or deliver it directly. We will take care of the rest. Your favorite device is in the best hands with us.
Make an appointment to send in your device.

Filter products

Potentiometer