Yamaha R-Serie

Panasonic

tactile switch 9,5 mm Yamaha

tactile switch suitable for Yamaha ModellsRS7000 (REC/Play/Stop/<)RM1X (Control Buttons without Keyboard)Motif 6, Motif 7,Motif 8 (switch without LED)Motif XS, Motif ES (switch without LED)Yamaha Part Number: VZ085500The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

ALPS

tactile switch 5 mm Yamaha RM1x - discontinued -

1 pcs tactile switch suitableYamaha RM1XYamaha MX100II disklavierThese switch is for Keyboard ButtonsYamaha Part Number: VS1809800The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 1 .25*

Panasonic

tactile switch 7 mm Yamaha

1 pcs. tactile switch suitable for Yamaha MotifOn Yamaha Motif modells these switch is for lightning buttons.These switch is also suitable forYamaha PSR9000Yamaha Tyros serie - without LCD BoardYamaha Part Number: VV439800,WG31840R, VQ371700The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

Nichicon

Bipolar Capacitor 1uF/50V for Audio, Radial, Nichicon Muse ES

1 piece bipolar Elko 1uF/50V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .93*

Jalco

YKB21-5012 - Phone Jack 1/4- 6.3 mm for printed circuits Mono

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit used in Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5012HLJ 4306HLJ 4306-01-3000Mono with switchit is used by the following manufaturesKorg partnumber: 454004300Roland partnumber: 13449146Yamaha partnumber: VB312600 YKB21-5012Yamaha partnumber: VE742000 HLJ 4306These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Jalco

YKB21-5010 - Phone Jack 1/4 - 6.3 mm PCB Stereo

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used in Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5010HLJ0520-01-010HLJ1520-01-3010HTJ-064-10Dsame PCB layout, different housingHLJ4416-01-3020it is used by the following manufaturesKorg partnumber: 454004400Roland partnumber: 13449125 HLJ0520-01-010Roland partnumber: 13449145 YKB21-5010Yamaha partnumber: VE382300Technical description Jalco YKB21-5010:The offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. This phone jack is available from various manufacturers in the same mechanical and technical construction. An exception is the manufacturer HOSIDEN using a wider housing. The electrical connection has the same structure.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .56*

Synth-Parts

Rotary Poti vertikal, 11x11 10kOhm

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos - MIX SectionRoland MC-909Yamaha RS-7000 - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 4 .94*

Varta

CR2032 Solder pin for Yamaha DX-Series

1 pcs. CR2032 with 2 solder pin suitable forYamaha DX7, DX7 II, DX9, DX27, DX100Yamaha TG77Yamaha RX5, RX7, RX11Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The distance between the solder legs is 15 mm.Manufacturer: Panasonic or VartaPractical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

€ 3 .49*

E-Switch

Single pole push switch, 250V/5A with solder lugs SDDLD10900

Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

€ 6 .95*

ALPS

Value Slider 30mm Travel for Korg

1 pcs. Mono Slider with 30mm Travel. Suitable for Value Slider for KorgN1, N5, N5ex, N264, N36401W, 01WFDX2, X3, X5, X5dM1, M1r, M3rT1, T2, T3WS, WSEXKorg spare part No.: 365007800The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 11 .45*

Synth-Parts

LED 3 mm Red

1 piece LED 3 mm Red The LED are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .99*

Synth-Parts

Potentiometer for Yamaha rm1x with center Tap 12mm

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionYamaha RM1x Utility Mounting instruction Yamaha RM1x:The potentiometer with thread I offer here can also be used in the RM1x. The great advantage of this solution is that I think potentiometers with threads will have much longer lifetime than potentiometers without threads. Indisputably, the axis is guided and stored much more stably by the thread.n the pictures you see a test installation I have made.Electrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 4 .70*

Panasonic

tactile switch 5 mm discontinued

tactile switch suitable for Keypad in these Groovebox'sRoland MC-303Roland MC-307Roland MC-505Roland MC-909 TAPYamaha RS7000Part Number:Roland 125590Yamaha V5914900The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 1 .76*

Synth-Parts

Replacement Set tactile Switch for Yamaha RS7000 complete

Complet replacement set tactile switch for Yamaha RS7000consist of:5 pcs 9,5 mm hight46 pcs 7 mm hight27 pcs Keypad switchOperational Life for all switch: 1.000.000 CyclesThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 29 .75*

Yamaha

Yamaha Replacement stereo rotary potentiometer 14mm

stereo rotary potentiometer for Volume, suitable forYamaha PSR-330 und 340PSR-530 bis 550PSR-630 und 640PSR-730 und 740PSR-1000, 1100, 1500PSR-2000, 2100, 3000PSR-S700 und S710PSR-S900 und S910CVP-207Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 6mm. It is made of black plastic. Its head has a slot and ends in corner radius.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 1 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 5 .77*

Synth-Parts

LED 3 mm Green

1 piece LED 3 mm Green The LED are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .99*

Synth-Parts

Replacement Set tactile Switch for Yamaha RM1x complete

Complet replacement set tactile switch for Yamaha RM1xconsist of:45 pcs 9,5 mm hight27 pcs Keypad switchOperational Life for all switch: 1.000.000 CyclesThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 39 .00*

Varta

CR2450

1 pcs. CR2450Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 24.7 mm and a thickness of 5mm. Manufacturer: Panasonic or Varta Information for handling old Battery's

€ 3 .88*

Yamaha

Knob for Yamaha RM1X

1 pcs. Knob for encoder knobs inRM1XMotif XS RackRS7000Praktical tip:The knobs are just plugged on. No tools are needed.

€ 6 .75*

Synth-Parts

Yamaha RM1x new LCD Display black plug and play

1 pcs. Black LCD Display with LED Backlight replacementYamaha RM1xWe offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character / Black BackgroundDelivery scope of LCD Display for RM1x:Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RM1x :To replace the display, the Yamaha RM1x is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters. Note on contrast adjustment:It may be necessary to replace 2 SMD capacitors on the main board. Due to the ageing of the capacitors, the setting range for the contrast has shifted.

€ 129 .00*

Synth-Parts

Yamaha RS7000 new LCD Display black plug and play

1 pcs. Black LCD Display with LED Backlight replacementYamaha RS7000We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character / Black BackgroundDelivery scope of LCD Display for RS7000 :Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RS7000 :To replace the display, the Yamaha RS7000 is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters.

€ 129 .00*

Synth-Parts

8 position rotary switch 16 mm widht

8 position rotary switch 16 mm widht suitable forYamaha RS-7000Mechanical Description:Technical Description:Practical advice:These rotary switch is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 14 .10*

Taiwan Alpha Electronic Co., LTD.

Encoder 16 mm for Yamaha

Encoder 16 mm widht suitable forYamaha RM1XYamaha RS-7000Practical advice:The thread of this encoder is 2 mm longer than the thread of the original encoders. Depending on the space in the housing, it can tighten a bit when reassembling. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 5 .63*

Synth-Parts

Replacement stereo rotary potentiometer 14mm

1 pcs. Replacement stereo rotary potentiometer 14mm widht for Volume, suitable forYamaha RS-7000Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 5 .89*

Filter products

Yamaha R-Serie