Roland HP-Serie

Panasonic

tactile switch 5 mm for Roland

1 pcs. tactile switch suitable for models RolandFP1, FP2, FP3, FP4, FP5, FP6, FP7, FP8, FP-50JV25, JV30, JV35, JV50, JV80, JV90, JV880, JV1080JP8000JD800 - Cursor ButtonsMC-303, MC-307RD-500XP10, XP50, XP60, XP80XV3080U20Fantom X6,X7,X8 without REC/PLAY/STOPOnly for non-illuminated buttons:A90, A90-EXXP30JV1000JP8080RD-600,RD-700Roland Part Number: 13169697 or 13169752The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

Roland

Replacement parts for Roland PA4 and PA4A Keyboard

Parts Keyboard: Fulcrum 12P

Spare parts for Roland PA4 and PA4AKeyboardHere you will find different parts for Progressive Hammer Action Keyboard from Roland. These PA4 Keyboard was build by Roalnd in two different Versions. There exists a PA4 and a PA4A Version. The Parts i offer here fits for both Versions. Cusion, FeltHammerKey GuidePrice is valid for one spare part. Lower Cusion for Hammer in a Roalnd PA4 or Pa4A Keyboard (PArt-No: TTROPA4-ZU-FLTHA1)This Cussion is needed to stop hammer when falling down.Roland use here a material based on two different components.One side is self-adhesive.For a complette Keyboard wit 88 Keys you will need 2 of these cusionTTROPA4-ZU-FLTHA1.For all other Felt and Cusions you will need one part for a complete Keyboard.

Variants from €1.49*

€ 17 .90*

Jalco

YKB21-5012 - Phone Jack 1/4- 6.3 mm for printed circuits Mono

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit used in Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5012HLJ 4306HLJ 4306-01-3000Mono with switchit is used by the following manufaturesKorg partnumber: 454004300Roland partnumber: 13449146Yamaha partnumber: VB312600 YKB21-5012Yamaha partnumber: VE742000 HLJ 4306These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Jalco

YKB21-5006 - Phone Jack 1/4- 6.3 mm for printed circuits Stereo

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 6 .88*

Nichicon

Bipolar Capacitor 4.7uF/25V for Audio, Radial, Nichicon Muse ES

1 piece bipolar Elko 4.7uF/25V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 0 .86*

Synth-Parts

Volume Slide potentiometer for Roland - EWA NA0X10A14

Volume Slide potentiometer with 30mm travel and 10mm Lever. Suitable forRoland FP-8Roland HP-900Roland HP-1700Roland HP-1700L This Lever is a little bit thinner than the original one.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

From

€ 7 .74*

Synth-Parts

Roland HP-330, HP-530 Volume Potentiometer

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland HP-330Roland HP-530Attention: Lever - Slide pin must be shortende around 5 mmThis volume control with the labelling EWANNBX10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .33*

ALPS

Single pole push switch, 250V/5A with solder lugs

1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsRoland HP-107eRoland Part Number: 72454101technical Dates:Voltage: 250VACCurrent: 5ATermination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for a screw in a housing and has two threaded holes with diameter 3,2 mm. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4 mm and a width of 2,8 mm.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

€ 9 .02*

Roland

Replacement Keys for Roland PA4 Keyboard

Key: Key A

Spare parts for Roland PA4 Keyboard Does a key on your electric piano hang or clack loudly when you play it? In these cases, it is usually not the key that is defective but the underlying hammer that is broken.This part fits for all Roland PA4 KeyboardsRoland PA4 Keyboard is used inRoland HP-237eRoland HP-555GRoland HP-7700Roland KR-370Roland KR-375Roland KR-570 und KR-575Roland KR-770Roland KR-1070Roland KR-4300Roland RD-500The S-Key fits in Keyboard PA4 AND PA4APlease have a look at the video for replacing Hammers.

Variants from €9.53*

€ 9 .98*

Synth-Parts

Roland HP series Volume Potentiometer

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland HP-136Roland HP-236Roland HP-237Attention: Lever - Slide pin must be shortende around 5 mmThis volume control with the labelling EWANNBX10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

€ 8 .33*

Synth-Parts

Power cable 3 pol C13 Socket, 1.8 m

1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m

€ 6 .45*

Roland

Replacement keys for Roland PHA Keyboard

Key: Key A

Replacement Keys for Roland Progressive Hammer Action Keyboard- PHA2Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107eColor/tint: pure white

€ 9 .62*

Synth-Parts

FFC socket 16 pin, 1.25 mm pitch

1 pcs. 16 pin FFC socket with 1.25 mm pitch16 pinPitch: 1.25 mmLength: 23,75 mmdeepth: 4,80 mmhight: 7,80 mmTechnical description

€ 3 .33*

Panasonic

tactile switch 5 mm for Roland

1 pcs. tactile switch suitable for modelsRoland MC-505Roland MC-808Roland MC-909Roland Part Number: 1343478The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From

€ 0 .65*

Synth-Parts

D/A-Converter PCM56P, DIL16

Digital-Analog-Converter for audio application for Roland E-PianosPCM56P von Texas InstrumentsThis part is used from RolandRoland part number:15209122 Resolution: 16bitInterface: seriellConversion rate: 666kS/sNumber of DAC outputs: 2Number of channels: 1Case: DIP16warm-up time: 1 minMechanical Description:The digital to analog converter is housed in a DIP 16 package and is designed for classic through hole mounting on a circuit board. Use of a socket is possible. The DA converter has 2 x 8 connecting pins with grid of 2.54 mm x 7.62 mm.Technical Description:This D/A converter was developed specifically for use in audio applications. The DA converter provides low distortion and typical differential linearity error is 0.001%. The interface is serial and provides a 16 bit resolution. The conversion rate is 666kS / s. For operation, no external components, such as temperature compensation or similar is required.It is a symmetrical supply voltage of +- 5V to +- 12V needed.

€ 28 .67*

Jalco

double DIN female 5 pin MIDI for printed circuits, Jalco YKF51-5048

1 pcs. double MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5048used by: KorgRolandYamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

€ 9 .78*

Hosiden

Phone Jack 1/4 - 6.3 mm for printed circuits Mono with switch

1 pcs. Phone Jack 1/4 inch- 6.3 mm, mono with switch, for printed circuitHosiden HLJ7101-01-3010 This phone jack is no longer manufactured and there are only remaining stocks.This part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Technics E-PianosTechnics KeyboardsPlease have a very detailed view on the picture. There is one Phone Jack very similar.Technical descriptionThe offered phone jack for PCB mounting is a Mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 7 .25*

Synth-Parts

Power cable 3 pol C13-plug, 2m

Power cabel 2m with 3P C13 plug

€ 7 .58*

Roland

Dual Button 12x5 mm with LED window for Roland- discontinued -

Dual Button for 12 x 5 mm Window Roland HP-900Roland HP-1700Roland KR-3000Roland U-20Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reasen for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 12 x 5 mm. This part has two Buttons and each button has a window for LED Light.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

€ 7 .90*

Roland

Hammer for Roland PHA Keyboard

Hammer: Hammer Zone 1

Hammer for Roland Progressive Hammer Action Keyboard- PHA2 and PHA3Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107e

€ 9 .62*

Roland

Replacement keys for Roland PHA Keyboard ivory

Key: Key A

Replacement Keys for Roland Progressive Hammer Action Keyboard- PHA2Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107eColor/tint: creme white (ivory)

€ 9 .62*

Roland

Roland PHA Keyboard Parts

Parts Keyboard: Chassis 12P

Roland Progressive Hammer Action Keyboard PartsHere you can find Chassis and PCB

€ 28 .99*

Synth-Parts

FFC socket 14 pin, 1.25 mm pitch

1 pcs. 14 pin FFC socket with 1.25 mm pitch14 pinPitch: 1.25 mmLength: 21,05 mmdeepth: 4,80 mmhight: 7,80 mmTechnical descriptionPraktikal tip:In these socket the cable cable have just to be pluged in.

€ 3 .33*

Roland

Mainboard Roland HP-330 HP-530 repair with 1 year warranty

1 pcs. Mainboard repair for Roland Roland HP-330Roland HP-530These Mainboard will repaired by us and fully working. We sell this repair with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.

€ 299 .00*

Filter products

Roland HP-Serie