Skip to main content Skip to search Skip to main navigation

Filter products

Kurzweil

ALPS

Average rating of 0 out of 5 stars

tactile switch 7,3 mm
1 pcs. tactile switch suitable for modelsKorg DW6000, DW8000Korg Poly 61Korg KPR 77Roland JX 8PRoland TR606, TB303Yamaha DX7, DX9Oberheim Matrix 6Kurzweil K1000Kurzweil K2000Part Number: Korg: 37505000, Roland: 1129715,Yamaha: KA905510The old productnumber was called: KHC10901The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From
0 .93*
Panasonic

Average rating of 0 out of 5 stars

tactile switch for Kurzweil
tactile switch suitable for KurzweilPC88, PC88mxThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

0 .67*
Fatar

Average rating of 0 out of 5 stars

Contact rubber for Fatar Keyboards
Kontaktgummi: 12 Contacts
Contact rubber for Fatar KeyboardsFatar uses in many different keyboards same contact rubber. The here offered contact rubber are suitable for!!!!!   Not for use in Roland Instruments    !!!!!Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP/10 MDRFatar TP/10 ABSFatar TP/40Fatar TP/100LRtechnichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greyFatar Keyboards are used by Clavia Nord, Döpfer, Ensonic, Korg, Kurzweil, GEM

Variants from €5.00*
10 .95*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil tactile switch 6.2 SMD 3.1 mm ground
1 pcs. Kurzweil SMD tactile switch with higth 3.1 mm suitable for models Attention: SMD (Surface Mounted Device) needs spezial soldering equipment and spezial experience in solderingThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 .13*
E-Switch

Average rating of 0 out of 5 stars

Single pole push switch, 250V/5A with solder lugs SDDLD10900
Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

6 .95*
Hosiden

Average rating of 0 out of 5 stars

HLJ0544 Phone Jack 1/4 - 6.3 mm PCB Stereo ,Iron frame
1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo, for printed circuit with Iron FrameThe item is the same asHLJ 0544-01-010Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating.Praktikal tip:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From
4 .87*
Nord

Average rating of 0 out of 5 stars

Nord Phone Jack 1/4 - 6.3 mm for printed circuits Mono
Phone Jack 1/4- 6.3 mm, Mono, for printed circuit used by  Clavia Nord PianosTechnical descriptionThe offered phone jack for PCB mounting is a mono jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

5 .49*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil K2000 LCD Display black with cable Kit NEW
Black LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionThis Display fits inNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

99 .00*
Synth-Parts

Average rating of 0 out of 5 stars

LCD Display blue with cable Kit for Kurzweil K2000
1 pcs blue LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation:The instrument must be almost completely disassembled to access the display. Please do not underestimate the amount of work that is necessary. This work should only be carried out by people with technical, preferably electrotechnical, experience.The installation itself can be done without any soldering skills, but: We recommend to take out of function circuit part for the old backlight foil. For this, a transistor and a capacitor must be removed. This can also be done with a side cutter, i.e. without soldering. 

99 .00*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil K1200R Rack OLED Display new blue
Brand new OLED Display, blue, forKurzweil K1200 Pro 1Brand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1200 Pro 1 Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

58 .99*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil K1000R Rack OLED Display new
Color: Blue
1 pcs. new Brand new OLED Display forKurzweil K1000 AX PlusKurzweil K1000 HXKurzweil K1000 PXKurzweil K1000 SXBrand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1000  Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1000 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

58 .99*
Varta

Average rating of 0 out of 5 stars

Battery 2/3 Solder pins
1 pcs. Battery with 3 solder pins suitable for  RPlease check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

14 .28*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil K1200R Rack OLED Display new white
Brand new OLED Display, white, forKurzweil K1200 Pro 1Brand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1200 Pro 1 Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

58 .99*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil PC3A LCD Display blue plug and play
1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKurzweil PC3A6Kurzweil PC3A7Kurzweil PC3A8We offer an absolutely equivalent display using modern LED technology for backlight.Note on the PC3X series from Kurzweil:The replacement display offered here is the appropriate replacement for Kurzweil displays that already use LED backlighting. This can be identified by a short 2-pin connector to the right of the display. Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement  Notes on installation The LCD Display in Kurzweil PC3XThe original Kurzweil display has different dimensions to today's commercially available displays. We have therefore developed an adapter board to adapt this. We supply the display pre-wired and pre-assembled.This work is to be done only by technically, best electrotechnically savvy people.The contrast and brightness of the display can be adjusted as usual using the controls in the instrument.No soldering required.All you need is a screwdriver and a side cutter. 

144 .99*
Cherry

Average rating of 0 out of 5 stars

Single pole rocker switch, 250V/6A with plug connections
Single pole rocker switch, switch design - OFF with plug connections suitable for modelsKorg Poly 61Korg Part Number: 375046006A / 250VACTermination plug1 poleMounting hole: 19,8 x 12,8 mmDimensions outside: 20,8 x 14,8 mmVDE-tested  Mechanical description:Housing material is NYLON 66. This switch is provided for a snap-in mounting and there are corresponding spring lips on the narrow side of the housing . The housing cutout for installation should be 19.30 mm x 12.90 mmDimensions of the switch are width of 12,90 mm, length is 18,60 mm and higth is 13,70 mm plus 2 mm hight for rocker. The outside dimensions are 21 mm x 15 mm.Elektrical properties:The electrical components are made of copper with a silver or tin plating and electrical connection is made via plug boots with 4.80 mm in width. The connection length is 7 mm.The electrical load is 6 A at 250 VAC.For switch replacement no special tools are needed because everything is plugged or clamped.

3 .61*
Fatar

Average rating of 0 out of 5 stars

Hammer for Fatar TP10 Keyboards
Hammer: Hammer black key
Hammer for Fatar TP10 KeyboardsFatar Keyboards are used by Korg, Clavia Nord, Kurzweil, GEM

7 .39*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil K2000 VOL-DATA ASSY NEU
1 pcs. Kurzweil K2000 VOL/DATA Assembly NEWKurzweil K2000There is a difference to original volume slider: The original volume slider has a logarithmic characteristic, here a linear characteristic was used for the volume slider.This completely assembled and mounted PCB is manufactured by ReBach from the Netherlands and is a 1: 1 replica of the original Kurzweil board. 

34 .00*
Panasonic

Average rating of 0 out of 5 stars

Battery 2/3 Solder pin
1 pcs. Battery with solder pin suitable for  RAttention: Shipping for Europe only Please check right polarity! The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

14 .28*
Fatar

Average rating of 0 out of 5 stars

Parts for Fatar Keyboards TP7/8/9
Ersatzteile Tastatur: Keyguide black
Parts for Fatar KeyboardsThese parts fits forFatar TP/7SFatar TP/8SFatar TP/9SHere you will find springs, felts, P.C.B., screws

Variants from €0.60*
3 .49*
Fatar

Average rating of 0 out of 5 stars

Replacement keys for Fatar TP/9 Keyboard, weighted
Taste: Key A
Replacement keys and spare parts for Fatar TP/9 KeyboardActual Keys in stock are strong darkened. Please refer the Photo.Fatar TP/9 keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 16 cm and a width of 2.24 cm. The thickness of the keys is 1 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 8,5 mm. The distance from the front side of the key is 11 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white. 

Variants from €5.70*
8 .90*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil K1200 Recapping Set complete
Recapping set for Kurzweil K1200The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set is made of Capacitors, which have been specially developed for use in audio applications. For us is manufacturer Nichicon the manufacturer with a good quality at reasonable prices offers.Manufacturer: NichiconThe Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

54 .74*
ALPS

Average rating of 0 out of 5 stars

Kurzweil PC88 Volume Potentiometer
1 pcs. Slider with 45mm Travel. Suitable for Kurzweil PC88The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

9 .90*
ALPS

Average rating of 0 out of 5 stars

Kurzweil PC88 Potentiometer für Value
1 pcs. Slider with 45mm Travel. Suitable for Kurzweil PC88The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

9 .90*
Synth-Parts

Average rating of 0 out of 5 stars

Kurzweil K1200 OLED Display new
Color: Blue
1 pcs. brand new OLED Display forKurzweil K1200 We offer here a brand new OLED display as a replacement for the originaly used LCD display. No Seldering is required. This OELD Display fit only for K1200 Keyboard VersionHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us ready wired. No soldering work is necessary for this installation. Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instruction Notes on disposal:every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components. 

58 .99*

Kurzweil spare parts in first-class quality

Kurzweil Music Systems, founded in 1982 by Raymond Kurzweil and Stevie Wonder (that's the one), became known for building and selling high-quality synthesizers. With the first musical instrument Kurzweil released in 1984, the K250, they immediately broke the "quality sound barrier", as this device was way ahead of its time in terms of emulating a piano sound. Ray Kurzweil, then a manufacturer of readers for the blind, made a bet with Stevie Wonder to see if it would be possible to build a synthesiser that sounded like a real piano. The result was the K250RMX, a keyboard-less rack version of the later K250 synthesiser/sampler.
Until 1990, when the company was sold to Young Chang, a Korean piano maker, Kurzweil brought many more instruments to market. For example the "1000 series" as well as the "2000 series" became very famous.

Spare parts for your Kurzweil instrument

Although Kurzweil instruments have the reputation of being very robust, they are also subject to the natural ageing of certain electronic components.
In the Synth-parts.com online shop, we have adapted to this and offer, for example, appropriate short-stroke switchesBatteries, etc.

Repair of your Kurzweil synthesizer

If you don't feel confident repairing your high-quality and aged Kurzweil device yourself, you can also commission our well-equipped specialist workshop. Here we have the appropriate measuring equipment and special tools with which our well-trained specialist staff can carry out the repairs properly and professionally. You can bring the entire unit to our workshop by appointment, or send in the assembly to be repaired. Make an appointment.