Casio VZ-10

Jalco

YKB21-5012 - Phone Jack 1/4- 6.3 mm for printed circuits Mono

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit used in Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5012HLJ 4306HLJ 4306-01-3000Mono with switchit is used by the following manufaturesKorg partnumber: 454004300Roland partnumber: 13449146Yamaha partnumber: VB312600 YKB21-5012Yamaha partnumber: VE742000 HLJ 4306These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .49*

Jalco

YKB21-5010 - Phone Jack 1/4 - 6.3 mm PCB Stereo

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used in Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5010HLJ0520-01-010HLJ1520-01-3010HTJ-064-10Dsame PCB layout, different housingHLJ4416-01-3020it is used by the following manufaturesKorg partnumber: 454004400Roland partnumber: 13449125 HLJ0520-01-010Roland partnumber: 13449145 YKB21-5010Yamaha partnumber: VE382300Technical description Jalco YKB21-5010:The offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. This phone jack is available from various manufacturers in the same mechanical and technical construction. An exception is the manufacturer HOSIDEN using a wider housing. The electrical connection has the same structure.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

From

€ 2 .56*

E-Switch

1 pcs. Single pole push switch, 250V/5A with solder lugs SDDLD10900

1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

€ 6 .95*

Synth-Parts

EL-panel, 41x67 mm for Casio VZ-1, VZ-10

1 pcs. EL-panel as sparepart for backlight inCasio FZ-10Casio FZ-10MCasio FZ-20MCasio VZ-1Casio VZ-10Be carefull: These backlights are very sensitive for heat. When soldering the cable necessarily make for a very good heat dissipation.

€ 19 .90*

ALPS

tactile switch 5 mm for Casio

1 pcs. tactile switch suitable for modelsCasio FZ-10MCasio FZ-20MCasio VZ-1Casio VZ-10MThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

€ 0 .73*

Varta

Battery 2/3 Solder pins for Casio

1 pcs. Battery with 3 solder pins suitable for Casio VZ-1Casio VZ-10M

€ 14 .28*

Filter products

Casio VZ-10