Skip to main content Skip to search Skip to main navigation

Filter products

Yamaha CVP Serie

Panasonic

Average rating of 0 out of 5 stars

tactile switch 7 mm Yamaha
1 pcs. tactile switch suitable for Yamaha MotifOn Yamaha Motif modells these switch is for lightning buttons.These switch is also suitable forYamaha PSR9000Yamaha Tyros serie    -  without LCD BoardYamaha Part Number: VV439800,WG31840R, VQ371700The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

From
€ 0 .65*
Yamaha

Average rating of 0 out of 5 stars

Yamaha GH3 NL2 Stopper Upper 88, felt
1 pcs. Yamaha GH3/NL2 Stopper U88 V8468201This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards. Old spare part no is: VU34210R 

€ 34 .89*
Yamaha

Average rating of 0 out of 5 stars

Yamaha GH3 NL2 Stopper Lower 88
1 pcs. Yamaha GH3/NL2 Stopper L88 - lower Felt V7640101This GH3 keyboard is used in these modells and others:Yamaha CLP-270This felt is also used in older Yamaha GHD keyboards. 

€ 27 .49*
Yamaha

Average rating of 0 out of 5 stars

Replacement Keys Yamaha GHD Keyboard
Key: Key A
Replacement Keys for Yamaha GHD KeyboardThese Keys fits for all Yamaha GHD keyboards.Note on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.Yamaha GHD keyboard is used in:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200This list of Yamaha Clavinova models is only a small selection. These keys were used in many models.Hanging Keys:In a series of these keyboards there was a problem with so-called hanging keys caused by the use of an unsuitable plastic grease.The key is clicked into the keyboard frame at the rear end. Yamaha originally used white grease here. This plastic grease has attacked the plastic of the key's. In the long run, this led to a material break at the back side of the key's (see photo 2).By this material break, the key is a bit wrong and thereby strikes the key next to it, dragging and is thus difficult (hangs). Instruments affected between May 2000 and January 2003 are affected.Today Yamaha uses a blue keyboard grease which is suitable for the plastic keys. If you still find this white grease in your keyboard, it is recommended to remove this grease and replace it with the blue one. For a keyboard should be 10 to 20 grams of grease.The Yamaha GHD keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

Variants from €6.89*
€ 8 .89*
Yamaha

Average rating of 0 out of 5 stars

Contactrubber GH3 for Yamaha
Contactrubber GH3 suitable for Yamaha This keyboard is used in these modells:Yamaha CVP-305Yamaha CVP-307And much more other Modells.For a complete Keybord with 88 keys you will need this quantity on contactrubber:1 x 5 contacts6 x 12 contacts1 x 11 contacts 

€ 13 .19*
Jalco

Average rating of 0 out of 5 stars

YKB21-5006 - Phone Jack 1/4- 6.3 mm for printed circuits Stereo
1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 6 .88*
Yamaha

Average rating of 0 out of 5 stars

Yamaha GH3 Actuate Rubber
1 pcs. Yamaha GH3 Actuate RubberThis rubber fits in these keyboardsYamaha GHDYamaha GH3Yamaha NL2This rubber is used on every single key as stopperColor: black 

€ 2 .08*
E-Switch

Average rating of 0 out of 5 stars

1 pcs. Single pole push switch, 250V/5A with solder lugs SDDLD10900
1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

€ 9 .45*
Yamaha

Average rating of 0 out of 5 stars

Yamaha Keyboard grease, blue 50g
Yamaha Spezial Keyboard grease, Blue 50gOriginal Yamaha plastic grease for Keyboards. Color is blue and will be delivered in a 50 gramm portion.Molycote G-1066YThis grease is used on YamahaOn GHD and GH3 keyboards on the fulcrum - Where the key engages the frame.For pedals at the mechanical moving parts. 

€ 35 .50*
Yamaha

Average rating of 0 out of 5 stars

Yamaha Pedalcable No3
1 pcs. Yamaha Pedalcable No3This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. All 6 wires are assigned on both sides.This cable is used in:Yamaha CLP-745Yamaha CLP-810SYamaha CLP-840Yamaha CLP-860Yamaha CLP-990Old Manufacturer Number: V0044700

€ 22 .90*
Jalco

Average rating of 0 out of 5 stars

Phone Jack 1/4 - 6.3 mm PCB Stereo with switch
Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in  Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 5 .81*
ALPS

Average rating of 0 out of 5 stars

Yamaha Stereo Potentiometer P85,, P120, P140
1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha P85Yamaha P120Yamaha P140 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

€ 9 .45*
Jalco

Average rating of 0 out of 5 stars

YKB21-5076 - Phone Jack 1/4- 6.3 mm PCB Mono
1 pcs. Phone Jack 1/4 inch - 6.3 mm, Mono witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5076HLJ-2305-01-3030These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

€ 4 .25*
Yamaha

Average rating of 0 out of 5 stars

Yamaha pedal felt black for E-Piano
1 pcs. Yamaha pedal felt black for E-PianoThe felt is coated with adhesive film on one side. 

€ 2 .94*
Yamaha

Average rating of 0 out of 5 stars

Pedal Volume Potentiometer
1 pcs. Pedal Volume PotentiometerThis is a replacement Poterntiomter for Pedal from E-Piano if there is a Volume Pedal installed.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Pedal.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

€ 14 .95*
Yamaha

Average rating of 0 out of 5 stars

Yamaha Pedalcable No6
1 pcs. Yamaha Pedalcable No6This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. All 6 wires are assigned on both sides.This cable is used in: 

€ 24 .89*
Yamaha

Average rating of 0 out of 5 stars

Yamaha NL2 Keyboard grease, white 50g
1 pcs. Yamaha Spezial Keyboard grease, white 50gMOLYKOTE G-1006YOriginal Yamaha plastic grease for NL2 Keyboards.Color is white and will be delivered in a 50 gramm portion.This grease can also be used on Yamaha GHD / GH3 keyboards at key guides.

€ 35 .50*
Yamaha

Average rating of 0 out of 5 stars

Yamaha GHD one octae white keys
One Octave white Replacement Keys for Yamaha GHD KeyboardThis set contains:1 x A1 x B1 x C1 x D1 x E1 x F1 x GNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key. 

€ 58 .49*
Yamaha

Average rating of 0 out of 5 stars

Yamaha GHD A88 Keyboard complete
1 pcs. Yamaha GHD A88 Keyboard complete--- shipping only in germany, sorry  -----Please ask if this keyboard is the right one for your e-piano model.This keyboard was used for many years in the vast majority of Yamaha electric piano models.The replacement of the entire keyboard is from a certain age of the electric piano well worth considering.For example, if your original keyboard is affected by the grease problem, you have here an alternative after desen exchange you no longer have to worry about the keyboard.If the keyboard is not in stock, we can order the keyboard from Yamaha. There may be a delivery time.

€ 399 .00*
Yamaha

Average rating of 0 out of 5 stars

Contactrubber for Yamaha GHD Keyboard
Rubbercontact: 11 Contacts
1 pcs. new Contactrubber for Yamaha GHD KeyboardThis keyboard is used in these modells and others:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha CVP-207Yamaha CVP-209Yamaha CVP-401Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200Color of these Contactrubber may be different.

Variants from €9.52*
€ 13 .24*
Synth-Parts

Average rating of 0 out of 5 stars

Yamaha CVP-209 Series FFC cable LCD to DM 500 mm
1 pcs. FFC cable for Yamaha CVP-209 500 mm length Length = 500 mmPitch= 0,5 mmBoth sides have the same connectorThis cable is used to connect LCD Display with Mainboard inYamaha CVP-207Yamaha CVP-209Yamaha CVP-900The LCD display in the Yamaha Clavinova has vertical stripes in the display?Do you have vertical stripes in the LCD display of your electric piano? These are lines that run from top to bottom through the display and do not belong in the picture.An exchange of this FFC cable can achieve an improvement. In the best case, the vertical stripes are then completely gone. 

€ 9 .97*
Yamaha

Average rating of 0 out of 5 stars

Yamaha Contactrubber 88P new -discontinued-
1 pcs Yamaha Contactrubber 88P newThis contact rubber was installed in different Yamaha keyboards and there are different spare part numbers for this spare part.A note about the contact rubbers: The contact rubber for the 88's keyboard was available in the colors pink and green. The pink contact rubber is missing 2 holes in the rubber which serve as a guide.The green version is no longer available.Note for the installation of the Yamaha contact rubber:Please pay attention to the installation position! The interruptions in the Konaktstreifen are not symmetrical. 

€ 36 .89*
Yamaha

Average rating of 0 out of 5 stars

Pedal Assembly for Yamaha E-Pianos XR780
Pedal: Contact Rubber 1P
Pedal Assembly for Yamaha E-Pianos XR780On this Pedal the PCB is fittet with Ground cable.Practice tip:Yamaha has built in a socket on the boards, which are built into the pedal which is perpendicular to the board. Here, the cable is plugged in that leads to the electronics of the electric piano in the upper part. As a result, this beech breaks out in the course of the operating years and it comes to the failure of the pedal.In most Repartur cases, it will be enough just to swap the socket.Depending on the model, this pedal was supplied with a potentiometer or contact rubber in the damper pedal. Please be sure to check the pedal before ordering a replacement part. 

Variants from €2.38*
€ 5 .90*
Yamaha

Average rating of 0 out of 5 stars

Yamaha Tyros Encoder 16 mm footprint
1 pcs. Encoder 16 mm widht suitable forYamaha Tyros 1Yamaha Tyros 2Yamaha CVP-207Yamaha CVP-209 Part numbers:Yamaha      VU48130R  REB161-PVB  

€ 8 .45*