1 pcs. IC Socket DIP 16 Gold for ICTechnical Hint:Mounting of this part requiers soldering.  

1 pcs Slide Potentiometer with 30mm Travel.Suitable for forRoland Jupiter 6Roand JX3PRoland SH-101       VCO Pulse Width, all Source Mixer,VCF Freq, VCF Res, Env, Kbd, Env Sustain The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Encoder 12 mm suitable for modelsRoland Juno Di, Juno G, Juno GiRoland Fantom X6Roland Fantom X7Roland Fantom X8Roland MC909Roland     part number: 03122134 and 01905467Practical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inRoland Juno 6Roland Juno 60Roland JX3PElectrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 17 mm, the total length without pins is 31,5 mm. In this total length the casing is 11 mm long. On this casing is the thread with 5 mm length connected. The axis has a diameter of 6 mm. It is made of Metall. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The six solder pins are 1 mm wide (one of them) and they are arranged in two rows in a distance of 5 mm (pitch).Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Power cabel 1,8 m with 2P plug for Europe  

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      A,D,S,R,LFOElectrical properties:The nominal resistance has 100 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      LFO Rate, DCO LFO,SUB OSC, NOISERoland Juno 60    LFO-RateElectrical properties:The nominal resistance has 50 KOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo with two switch, for printed circuitThis part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Yamaha DX7Technics SX -PX20Technical descriptionThe offered phone jack for PCB mounting is a stereo jack two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

tactile switch suitable for modelsRoland D5Roland D10Roland U220Part no: 13169684The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs Encoder EC24B50D Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. 26 pin FFC socket with 1.25 mm pitch right angel26 pintop contact sidePitch: 1.25 mmThis FFC Socket is used in Roland JD-800. This is located on small PCB under Keyboard

1 pcs. Roland MC303 and MC505 Encoder Board newThis Encoder PCB is suitable forRoland HP-557Roland MC303Roland MC505Mechanical Description of Roland MC505 Encoder Board:Roland used a Panasonic encoder with the designation EVQ-VEM-F01-24B in the above instruments. The production of this encoder at Panasonic was stopped many years ago.We have developed an adapter board on which a today's common encoder is soldered. This adapter board is soldered directly onto the Roland electronics.The switching feel is a bit harder with this new encoder than with the original.The new encoder has a metal housing and a plastic axle. Practical advice for Mounting MC303 Encoder :The encoder is permanently soldered onto a circuit board. Manual skills and experience in soldering are required for replacement. 

1 pcs. CD4052BE Multiplexer, DIP16Mechanical Description:The Multiplexer is housed in a DIP 16 package and is designed for  mounting on a circuit board. The Logic Circuit has 2 x 8 connecting pins with grid of 2.54 mm x 6.6 mm.Technical Hint:Mounting of this part requiers soldering.Integrated Circuits are  

1 piece EPROM with ROLAND JUNO 2 OS version 2.5 with OLED Support.This OS works only in Juno-2.we offer here a Customized OS version for the Roland Juno2 . This OS version is required if a new OLED display is to be installed in the Juno2 .There are two OS versions 2.5Roland released version 2.5 as the last official OS version. This version was then changed again for OLED support. The version number was not incremented. The OS version with OLED support is not an official Roland version.Mounting instructions for the EPROM in the Roland Juno2 :Soldering may be required if the EPROM in the Roland Juno2 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland HP-136Roland HP-236Roland HP-237Attention: Lever - Slide pin must be shortende around 5 mmThis volume control with the labelling EWANNBX10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuitHosiden HLJ7001-01-3010This part is used inRoland JP-8000Technics E-PianosTechnics Keyboards Technical descriptionThe offered phone jack for PCB mounting is a Stereo jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Slide Potentiometer with 30mm Travel. (Custom Built with dust cover for Synth-Parts)Suitable for forRoland SH-101      Lfo Rate, Lfo Mod. Env ModThese potenziometer are brand new ALPS Potentiometer. Additional benefit is a dust cover diectly mounted on housing.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. IC Socket DIP 8 Gold for ICTechnical Hint:Mounting of this part requiers soldering.  

Roland replacement keys, unweighted for SK3 keyboardColor: Pure whiteThe Roland SK3 keyboard is a non-dynamic keyboard with unweighted keys.The unweighted keys are 17 cm long and 2.2 cm wide. The height of the key is between 2.6 cm and 3 cm at its core. The spring is attached to the end of the key.The keys are pure white in color.

1 pcs. CR2032Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Manufacturer: Panasonic or Varta Information for handling old Battery's

1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for models technical Dates:Voltage: 250VACCurrent: 5ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for Cable mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland TB-303technical Dates:Termination Solder PinSchwitch: OpenMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for this replacement.

Roland Roland Juno 60 Fader Set complete This Set contains:1 pcs. Fader 30mm    10KB1 pcs. Fader 30mm    50KA1 pcs. Fader 30mm    1MA16 pcs. Fader 30mm    50KB Useful hint to Roland Juno 60 Fader Set:The lever on the original potentiometer is straight. The lever on the potentiometer offered here adapts to this shape because it is slotted.Arrangement of the solder pins: The solder pins on this replacement part are slightly offset. The solder pins must be bent slightly before soldering.The control is soldered firmly onto a circuit board. Replacing the control requires manual dexterity and experience in soldering.

Roland Progressive Hammer Action Keyboard PartsHere you can find Chassis and PCB