Stereo slide potentiometer with 30mm travel and 10mm Lever. Suitable Slider forVolume Control forRoland D10Roland D20Roland D50Please note: the original lever (sliding pin) is slightly thicker.The cap will sit loosely with the new Potentiometer. This can be remedied with a little paper, for example. Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 piece bipolar Elko 4.7uF/25V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland Juno 1       VolumeRoland Juno 2       VolumeRoland JV-80         Volumen,Presence,C1Roland JV-90         Volumen,Presence,C1Roland RD-250s    VolumeRoland RD-300s    VolumeThis volume control with the labelling EWANA0X15B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo witch switch, printed circuit Jalco YKB21-5078 with 9 Solder Lugsthis Phone Jack corresponds to these parts:YKB21-5078HLJ-2305HTJ-064-16DThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

1 pcs. IC Socket for D5534ATechnical Hint:The IC socket has 17 legs with a grid of 2 mm. The IC D5534A has 16 legs + an empty position as a built-in marker. I think it makes sense to take over this empty position for the IC socket as well. The corresponding soldering pin can be easily pushed out.Mounting of this part requiers soldering. 

LED-tactile switch suitable for modelRoland TR-909LED colour: RedRoland replacement part no.: 13169627The construction part is not longer built. The old serial number was KHJ-11901. With that serial number the part was built during the 80s.We offer here switch from the second redesigned series where LED body is clear.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsRoland MC-505Roland MC-808Roland MC-909Roland Part Number:  1343478The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Contact rubber 12 points for Roland PHA KeyboardFor PHA Keyboard from Roland exists to different Contactrubber. One Version owns two contacts for each Key and one Version owns three contacts for each Key.Please have a look on your Keyboard before ordering.Contact high:  7,5 mmStrip bright:   22,3 mmStrip length:  165   mmNumber of contacts: 12Roland Part Number: 4671145A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 88 keys 7 contact strip + 4 pins are needed. The remaining 4 contacts can be easily separated from a rubber contact strip with 12 contacts. A notch is provided in the rubber contact strip after every four contacts for this purpose.

1 pcs. Cap rectangular for power switchPlease note the dimensions. The original caps used to be larger on many instruments. Dimensions: 12 x 7 mmHight: 10 mm

1 pc. Contact rubber for old Roland keyboard Features:    Height of contacts: 8 mm    width of the strip:   16 mm    Length of the strip: 162 mm    Number of contacts per strip: 12 contactsOne contact strip consists of 12 contacts and thus covers one octave.This contact rubber has a notch to allow the contact rubber to be split. The division occurs with 7/5 contacts 

1 pcs. OLED Display brandnew in white forRoland D-550this is  a plug in ready Display replacement for Roland D-550. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation:We deliver this OLED dislpay for the Roland D-550 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inRoland Juno 106Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 17 mm, the total length without pins is 31,5 mm. In this total length the casing is 11 mm long. On this casing is the thread with 5 mm length connected. The axis has a diameter of 6 mm. It is made of Metall. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The six solder pins are 1 mm wide (one of them) and they are arranged in two rows in a distance of 5 mm (pitch).Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. triple MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. This is a 1:1 replacement for the MIDI jack in newer Roland instruments.used by:Roland These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Spare parts for Roland SK7 KeyboardThis part fits for all Roland SK7 KeyboardsRoland SK7 Keyboard is used inD-70JD-800U-20 This keyboard is no longer available from Roland. Production discontinued. 

1 pcs. Phone Jack 1/4 inch - 6.3 mm, Mono witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5076HLJ-2305-01-3030These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Roland XV3080 and XV5080 Encoder Board newThis Encoder PCB is suitable forRoland XV3080Roland XV5080Mechanical Description of Encoder Board:we deliver a brand new Encoder and a PCB for self soldering. The cable has to be taken over from orignial Encoder Board. This new Encoder has housing from Metall and a plastik axis.Practical advice for Mounting:The encoder is permanently soldered onto a circuit board. Manual skills and experience in soldering are required for replacement. 

16 pcs. Slide potentiometer with 30mm travel and 15mm Lever. (Custom Built with dust cover for Synth-Parts)Suitable forRoland Juno 106        all without Bender BoardWe offer here a special version of this slider including a Dust CoverThis volume control with the labelling EWA-NK0D15B54 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 50 kOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of metall. Its height is 15 mm, the breadth is 4 mm at the top and 5 mm at the bottom. Depth is 1,2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. CR2032 with solder pin suitable for  Roland Juno 106Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version.Practical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

tactile switch suitable for Keypad in these Groovebox'sRoland MC-303Roland MC-307Roland MC-505Roland MC-909   TAPYamaha RS7000Part Number:Roland 125590Yamaha V5914900The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. HEC2305-016250 DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland EP7 IItechnical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Slide Potentiometer with 30mm Travel. (Custom Built with dust cover for Synth-Parts)Suitable for forRoland JX-3PRoland SH-101      Env Attack, Decay, ReleaseThese potenziometer are brand new ALPS Potentiometer. Additional benefit is a dust cover diectly mounted on housing.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      HPF,VCF FRQ,VFC RES, Bender VCFRoland Juno 60   all, without Arp-Rate, LFO-Rate, Bender DCOElectrical properties:The nominal resistance has 50 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Wave Generator IC D5534A clonewe offer here a brand new clone of the original Roland Wave Generator Chip with some Mechanical Description:This Chip is manufactured by Analogue Renaissance with modern and actual SMD technic. The outline Dimensions and Pin configuration are same as the original Roland Wave Generator Chip MC5534A.Technical Hint:Mounting of this part requiers soldering.Integrated Circuits are