Volume Slide potentiometer with 30mm travel and 10mm Lever. Suitable forRoland FP-8Roland HP-900Roland HP-1700Roland HP-1700L This Lever is a little bit thinner than the original one.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6     Bender-DCORoland Juno 60    Bender-DCOElectrical properties:The nominal resistance has 1 MOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. OLED Display New forRoland Alpha Juno-1Roland Alpha Juno-2This OLED Display for Roland Alpha Juno-1 and Roland Alpha Juno-2 replacement is a really easy swapping. We will prepare this oled display in this way that ou will only need a screwdriver. Cable connection is done into a socket.Advice to Eprom Version in Roland Juno 1 and Juno 2Does the display only show half? That is, the first 8 characters are displayed normally but the remaining 8 characters remain dark? This can happen with an old Eprom version in the instrument. In this case the Eprom must be replaced by a current OS version.For Roland Juno 2 exists to different OS version 2.5. Only one supports OLED. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      ENV, KYBD,PWMElectrical properties:The nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Electrolytical Capacitor 10uF/25V SMDManufakturer: NichiconSerie: UQ for Audio Especially with SMD Elkos we often have the experience that these Elkos are often leaking after 20 years of operation and urgently need to be replaced.I offer here Elkos manufacturer Nichicon, these are used in audio, hi-fi and musical instruments.The UQ series was specially developed for use in audio technology.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

Recapping set for Roland Juno 106The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Roland Juno series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made of Capacitors, which have been specially developed for use in audio applications. For us is manufacturer Nichicon the manufacturer with a good quality at reasonable prices offers.Manufacturer: NichiconThe set consists of 88 electrolytical CapacitorsThe Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Replacement rotary potentiometer suitable for Roland MCRoland MC 303   -Volume / Low BoostRoland MC 505Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Single-pole push switch in the switch design - OFF with solder Pins for PCB mounting suitable for modelsKorg EA-1Korg EMX-1Korg ER-1Korg Part Number: 375014800technical Dates:Voltage: 250VACCurrent: 5ATermination Solder PinVDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for P.C.B. mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. HEC470-01-630 DC Power Jack with solder Pins for PCB mounting We offer the original Hosiden power socket here. Mechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 3 A at 16 VDC. Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.  

1 pcs. Replacement rotary potentiometer suitable forRoland MC 303Roland MC 505Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 piece LED 3 mm Redin 

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland HP-330Roland HP-530Attention: Lever - Slide pin must be shortende around 5 mmThis volume control with the labelling EWANNBX10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Roland Toggle switch, 2 pol 3 position with solder pins for PCBused inRoland Juno 106Roland Juno 60technical Dates:Termination Solder Pin3 PositionPractical advice:Knowledge in soldering is required for switch replacement.

1 pcs. Roland MC505 Potentiometer Part MixerDrop In Potentiometer for Section Part Mixer in Ronad MC-505. The lever must be shortened by 5 mm so that it fits in the Roland MC505. This can be done quite easily with a side cutter. Best to be done before soldering.This Fader with the labelling EWANKEC10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of metall and ends in corner radius. Its height is 10 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The potetniometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland JD-800 VolumeRoland XV-88 VolumeThe plastic lever must be shortened. The original potentiometer has a 5 mm sliding pin.This volume control with the labelling EWANA0X5B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Replacement–set for broken key guides on Roland SK3 KeyboardsWith Roland Synthesizer and electric pianos, it can happen over time that the original key guides break because of aging. This leads to a hanging or grinding of the keys. Since there are no more original spare parts for old Roland instruments, we have been looking for an alternative. Through various application tests and material research, we have found a product that fulfills the characteristics of the original Roland key guides in an identical way. Therefore we offer you a matched spare part set for your Roland piano in our store.So that everyone can get an impression of our product and the handling or the exchange, we have prepared a suitable blog post and a PDF variant to print out. YIncluded in the set:– Matched tube suitable for a keyboard with 88 keys.Tecnical advice for Grease:As we know there was no use of grease in these old keyboards. 

1 pcs. LCD display with LED backlightsuitable forRoland W-30We offer here a high quality replacement display with modern LED technology for the backlight.Mounting of LCD Display is plug and play. No soldering is required.Color: white font/blue backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable ready to plug in. Roland used in W30 a very special connector. We rebuild theses connector with handcraft pincompatible to the original one. Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland W30:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation. For this you have to cut two small componnents. No soldering is required.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.

1 pcs. Alfa Rpar AS3109 VCF IC DIP16 replacement for Roland IR3109The IC Alfa Rpar AS3109 is a voltage-controlled filter module that was used in analogue synthesizers in the 1980s. The AS3109 is pin-compatible with the Roland IR3109. Mechanical Description of AS3109:This AS3109 is housed in a DIP 16 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The IC has 2 x 8 connecting pins with grid of 2.54 mm x 7.62 mm.Technical description of the AS3109:Voltage-controlled four-pole filter. The four independent sections can be connected together to enable a variety of filter responses, including common filters such as low-pass, high-pass, band-pass and all-pass. A single input exponentially controls the frequency over greater than a 15 octave range with little control voltage feedthrough. AS3109 benefits from high input impedance buffers.Pin-compatible replacement for the IR3109.Technically, the IC may differ slightly from the original. When replacing a Roland IR3109, the entire instrument must be recalibrated.The IR3109 was installed by Roland in the Jupiter series, the Juno series, the SH-101 and others, among others.Practical tips:These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Please be carefull because of static charing 

Phone Jack 1/4 inch- 6.3 mm, Stereo with two switch, for printed circuit used inThese Phone Jack is in a simple version used inRoland Juno 6Roland Juno 60Technical descriptionThe offered phone jack for PCB mounting is a stereo jack two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Excessive legs can be cut off until the right configuration is achieved.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

34 tactile switches  suitable for  Roland Juno 106Roland S-50Roland Part Number: 13169633 The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Replacement rotary potentiometer with center click suitable forRoland MC-303 LFO DepthRoland MC-505Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit for Roland A-50Roland A-80We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope:DisplayMounting partsInstruction for replacementReady wired with original cableBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. We strongly recommend to disable electronic circuit that generates backlight voltage for old display. This is described in our manual. This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. OLED Display brandnew in white forRoland D-50this is  a plug in ready Display replacement for Roland D-50. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation:We deliver this OLED dislpay for the Roland D-50 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Instructions are enclosed with the display.For a detail mountint manual you can have a look here on Supersynthprojects. Please note, ouor display is ready wired:Roland D-50 mountingThe color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

Recapping set for Roland XV-5080 Mainboard The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.From our repair experience we know that the SMD electrolytic capacitors used in the Roland XV-5080 are now defective due to age.On the mainboard of the XV-5080 also some classic cup electrolytic capacitors have been used. These electrolytic capacitors are usually inconspicuous and intact. Manufacturer: NichiconThe set consists of 23 SMD electrolytical Capacitors.The board also uses 2 bipolar, i.e. non-polarized capacitors.This Recapping Set contains all SMD Capacitors for Mainboard recapping in Roland XV-5080.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.