Keyboards

1 piece Gold-Cap 1 F/5,5 V Manufakturer: Elna or Panasonic  

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland D-70    - C1, BrightnessRoland JD-800  - Lever shorten!!!Roland PG-300Roland PG-800This Fader with the labelling EWANFX15B15 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Attention:Special pin layout. This potentiometer has a special pin layout and can only be used as a replacement for EWANFE or EWANFJ potenziometers. Not suitable for EWANA potentiometers.Without center. This potentiometer is only available without center.Electrical properties:The nominal resistance has 100 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The potetniometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Pedal Assembly for Yamaha E-Pianos XR780On this Pedal the PCB is fittet with Ground cable.Practice tip:Yamaha has built in a socket on the boards, which are built into the pedal which is perpendicular to the board. Here, the cable is plugged in that leads to the electronics of the electric piano in the upper part. As a result, this beech breaks out in the course of the operating years and it comes to the failure of the pedal.In most Repartur cases, it will be enough just to swap the socket.Depending on the model, this pedal was supplied with a potentiometer or contact rubber in the damper pedal. Please be sure to check the pedal before ordering a replacement part. 

Kawai Pedalcable No2

1 pcs blue LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation:The instrument must be almost completely disassembled to access the display. Please do not underestimate the amount of work that is necessary. This work should only be carried out by people with technical, preferably electrotechnical, experience.The installation itself can be done without any soldering skills, but: We recommend to take out of function circuit part for the old backlight foil. For this, a transistor and a capacitor must be removed. This can also be done with a side cutter, i.e. without soldering. 

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forAKAI MPC-1000We offer an brand new display with LED technology for backlight. Display is ready mounted, no soldering is requiered.Display with white letters and black BacklightDisplay design upgrade:AKAI has built in a display with a yellow-green backlight that breaks out of the housing and disturbs the elegant appearance of this instrument. We offer a new display that matches the black case of the AKAI MPC-1000. The display fits harmoniously into the design of the sampler.Display defective?Our display is also suitable as a replacement part if the original LCD display is defective. It doesn't matter if only the backlight is no longer working or if the LCD is without function. Our display is perfectly suitable as a replacement display for the AKAI MPC-1000 sampler.Or are you looking for a Christmas present?Are you looking for a gift for an ambitious musician who works a lot with AKAI samplers or who has always been annoyed by the original display? How about a new display that visually enhances the device and also increases the value of the instrument.Unfortunately, we cannot offer the complete instrument, but only a new LCD display.The color of the shown display on picture, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display is ready wired on delkiveryMounting parts if necessaryNotes on installation:The display is prepared by us ready wired and no soldering is required. All adjustments to the technical features of the MPC sampler are made by us on the display. Plug and Play installation. The new display is installed in exactly the same way as the old display was removed. For this reason, we do not provide installation instructions here. Nevertheless, we would like to point out that there is very little space in most devices. This work should only be done by technically experienced people.When switching on the new display for the first time, the optimum contrast point must be adjusted. This is achieved by pressing and holding the Stop key and turning the data wheel.  Installation service:We are also happy to install the display for you. Please ask.  

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument. Please let us now your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people.We are proud to offer the thinnest displays available on the market. 

1 pcs. brand new Sequential Circuits, SCI Potentiometer 100kOhmSequential Circuits Prophet 5 REV2     Serial 183 - 1300This potentiometer is only for the instruments built between 1978 and 1984.The potentiometers that were installed in the Prophet 5 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 100 KOhmChanges to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread          Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.      The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. IC Socket DIP 8 Gold for ICTechnical Hint:Mounting of this part requiers soldering.  

1 pcs. Yamaha FUSTB AC-IN BoardFor Europe only: 230VACUsed inYamaha CLP-575 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg 01R/W Rack ModulDisplay for Korg 01/W Keyboard Version plese order hereWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope for LCD Display:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01/RW:The instrument must be disassembled almost completely to reach the display.The rack version of the Korg 01/RW synthesizer has much less mechanical effort than the keyboard versions.For the new display to work, one SMD resistor on the mainboard of the Korg 01/RW must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/RW have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Quasimidi button cap blue Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. Korg M1 Volume Slider The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Replacement rotary potentiometer plastic axis suitable forQuasimidiElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. The axis has a diameter of 6 mm and is Knurled on a length of 7 mm. It is made of Plastik. Its head has ends in corner radius.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Yamaha DX7 II OLED Display NEW whiteReady-to-plug prepared OLED display for replacement in Yamaha DX7 II. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Mechanical hints for the replacement of the OLED display in the Yamaha DX7II:Please consider in this case that the mechanical effort to get to the display in the instrument is quite high. Among other things, the keyboard and the mainboard must be disassembled. Everything is screwed. No soldering necessary.The display has a cover made of Plexiglass which is glued on the display and has to be transferred to the new display. We have had good experience with the following method: Insert fishing line or sturdy sewing yarn between the display and the cover and use a sawing motion to separate the adhesive.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Black LCD Display with LED Backlight replacementYamaha RM1xWe offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display for RM1x:Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RM1x :To replace the display, the Yamaha RM1x is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters. Note on contrast adjustment:It may be necessary to replace 2 SMD capacitors on the main board. Due to the ageing of the capacitors, the setting range for the contrast has shifted. 

1 pcs.Clavia Nord LCD Display new white Replacement LCD Display for Claiva Nord Instruments. For installation soldering is requiered.Notes on installation for Nord LCD Display:This LCD Display is soldered to a PCB only with a small connector. This requieres very good soldering knowlege. Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 20,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.  

Replacement keys for KAWAI Keyboard RG-88Bsuitable forKawai CN14Kawai ES6Kawai ES100The Kawai RG88B keyboard is a velocity sensitive keyboard with 4-zone hammer action.4-zone hammer action:With the 4-zone hammer action, Kawai is trying to get even closer to the feel of a mechanical grand piano than was possible with the previous hammer action keyboards. The keyboard touch of a mechanical piano is different in weight depending on the zone, whether bass or in the high range. This is simulated in the Kawai RG88B keyboard by the fact that there are four different hammers with different weights.The 4-zones are divided as follows:Zone 1, Bass - note 1 to 15Zone 2, middle1 - note 16 to 32Zone 3, middle2 - note 33 to 63Zone 4, soprano - note 64 to 88 

Roland replacement keys, unweighted for SK3 keyboardColor: Pure whiteThe Roland SK3 keyboard is a non-dynamic keyboard with unweighted keys.The unweighted keys are 17 cm long and 2.2 cm wide. The height of the key is between 2.6 cm and 3 cm at its core. The spring is attached to the end of the key.The keys are pure white in color.

Replacement Hammer for RH3 KeyboardThe RealHammer 3 (RH3) keyboard is a 4 zone hammer mechanism.

1 pcs. Battery with 3 solder pins suitable for  RPlease check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Encoder 22 mm without Detent.Also suitable for:Nord Modular G2  - Secondary Dial Master Clock -> Patch LevelPractical adviceThe encoders offered here come from the same manufacturer as those used by Nord. There are small deviations in design compared to the original:Pin distance here is 2.5 mm compared to 5 mm for the originalOriginal encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases at Nord and can be removed. These encoder are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Small soldering job to do.Color: White Character  /  Black BackgroundDelivery scope of Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Please let us know your Instrument, so we can put on right cable length onto your Display.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people. 

Replacement stereo rotary potentiometer suitable for volume control inKorg 05RWKorg TR RackKorg X5DRThis volume control is no longer available by Korg. The here shown replacement pot is build with a 2,5 mm longer axis.Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch). At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.