Keyboards

1 piece LED 3 mm Green The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. tactile switch suitable for models E-mu E4K          - Rec,Play,Stop,FW,RWE-mu E-Synth     - Rec,Play,Stop,FW,RWThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Slider set brand new Sequential Circuits, SCI Potentiometer forSequential Circuits Prophet 5 REV1     Serial 1 - 182Sequential Circuits Prophet 5 REV3     Serial  from 1301 to endThe potentiometers that were installed in the Prophet 5 and also in the Prophet 10 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 10 KOhmQuantity: 26 pcs.Changes to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread          Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.      The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

Complete Set tactile switch suitable for modelsYamaha DX7 IIYamaha DX7 IIFDYamaha Part No: KA907030The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for models technical Dates:Voltage: 250VACCurrent: 5ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for Cable mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland TB-303technical Dates:Termination Solder PinSchwitch: OpenMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for this replacement.

Roland Roland Juno 60 Fader Set complete This Set contains:1 pcs. Fader 30mm    10KB1 pcs. Fader 30mm    50KA1 pcs. Fader 30mm    1MA16 pcs. Fader 30mm    50KB Useful hint to Roland Juno 60 Fader Set:The lever on the original potentiometer is straight. The lever on the potentiometer offered here adapts to this shape because it is slotted.Arrangement of the solder pins: The solder pins on this replacement part are slightly offset. The solder pins must be bent slightly before soldering.The control is soldered firmly onto a circuit board. Replacing the control requires manual dexterity and experience in soldering.

1 pcs. Battery holder for CR2032 for PCB mountingAttention: Shipping for Europe only Technical Description:  Information for handling old Battery's

Roland Progressive Hammer Action Keyboard PartsHere you can find Chassis and PCB

1 pcs. Button SmallKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of  mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. OLED Display New forSequential Circuits Prophet VSSequential Circuits Prophet VS RackSequential Circuits Studio 440To replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs.  FFC cable 26 pin 1.25 pitch 420 mm Length = 420 mmsame side contacts.

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu E4XTE-mu e6400We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in E-Mu e6400:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. Yamaha Pedal screwDimensions: M6 x 57 mmNote:At 38 mm, this pedal support bolt has a longer thread than the one under item numberSCYA-WF054500

1 pcs. Kawai Volume Slider KnobKawai MP-8Kawai MP-11 Technical Description of Kawai Button:This Volume Slider knob will be put on slide potentiometer on your Kawai Stage Pianos

1 pcs. Korg Kronos Slider VR KnobKorg Kronos 61Korg Kronos 73Korg Kronos 88Korg Kronos Slider VR Knob X09130 SVR KNOB-B/G E40805-2Technical Description of Korg Kronos Slider Knob:This Slider knob will be put on slide potentiometer on your Korg Kronos Synthesizer. There is no tool needed.

1 pcs. Service Kit Kawai WN88 PWB Assy KKB-039This service kit replaces the circuit boards and contact rubbers in the Kawai WN88 keyboard. Only possible as a replacement for keyboards in which contact rubbers with three contacts per tone were used.This set of boards replaces the board KKB-039.The set consists of two boards, fully equipped with new contact rubbers.These Board fit in these e-pianos:Kawai CA65Kawai CA95Kawai CS7Kawai CS10Kawai MP11Kawai VPC1

1 pcs. 26 pin FFC socket with 1.25 mm pitch right angel26 pintop contact sidePitch: 1.25 mmThis FFC Socket is used in Roland JD-800. This is located on small PCB under Keyboard

1 pcs. Yamaha Key emmission circuit Board for Hybrid Pianosthis PCB is used inYamaha MP-100Yamaha GT-1and other Hybrid and Silent Pianos Assembly note:On older instruments, the plastic housing was deeper. To compensate for this, cardboard strips are included with the circuit board. 

1 piece EPROM with ROLAND JUNO 1 OS version 4.0 with OLED Support.This OS works only in Juno-1.we offer here a Customized OS version for the Roland Juno1 . This OS version is required if a new OLED display is to be installed in the Juno1 .Mounting instructions for the EPROM in the Roland Juno1 :Soldering may be required if the EPROM in the Roland Juno1 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

1 piece EPROM with ROLAND JUNO 2 OS version 2.5 with OLED Support.This OS works only in Juno-2.we offer here a Customized OS version for the Roland Juno2 . This OS version is required if a new OLED display is to be installed in the Juno2 .There are two OS versions 2.5Roland released version 2.5 as the last official OS version. This version was then changed again for OLED support. The version number was not incremented. The OS version with OLED support is not an official Roland version.Mounting instructions for the EPROM in the Roland Juno2 :Soldering may be required if the EPROM in the Roland Juno2 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

Replacement keys for KAWAI Keyboard RH-88Dsuitable forKawai CN35Kawai CN39Kawai ES8Kawai MP7SEThe Kawai RH88D keyboard is a velocity sensitive keyboard with 4-zone hammer action.This keys are weigted.4-zone hammer action:With the 4-zone hammer action, Kawai is trying to get even closer to the feel of a mechanical grand piano than was possible with the previous hammer action keyboards. The keyboard touch of a mechanical piano is different in weight depending on the zone, whether bass or in the high range. This is simulated in the Kawai RH88B keyboard by the fact that there are four different hammers with different weights.The 4-zones are divided as follows:Zone 1, Bass - note 1 to 15Zone 2, middle1 - note 16 to 32Zone 3, middle2 - note 33 to 63Zone 4, soprano - note 64 to 88 

1 pcs. Slide potentiometer with 20mm travel. Suitable forRoland TR-707Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements.The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. OLED Display New forE-Mu Orbit V1E-Mu Orbit V2These different Display versions are available:BlueRed/OrangeYellowWhiteTechnical Hint for Mounting the OLED Display in E-Mu Orbit:The OLED display is supplied fully wired. The installation is possible without any problems. The display is screwed and the cable is only plugged in. Please make sure that the cable marking is plugged into pin 1 of the connector. Since the new OLED display has a lower height than the original LCD display, we supply washers and new screws to compensate for the height.Plug of Power cable. Don't work under Supply Voltage!!Lifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.