Keyboards

1 pcs. Yamaha GHD A88 Keyboard complete--- shipping only in germany, sorry  -----Please ask if this keyboard is the right one for your e-piano model.This keyboard was used for many years in the vast majority of Yamaha electric piano models.The replacement of the entire keyboard is from a certain age of the electric piano well worth considering.For example, if your original keyboard is affected by the grease problem, you have here an alternative after desen exchange you no longer have to worry about the keyboard.If the keyboard is not in stock, we can order the keyboard from Yamaha. There may be a delivery time.

1 pcs. black LCD Display with LED Backlight replacement for ALESIS Andromeda We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color:  white Character / black BackgroundDelivery scope:Display ready wiredMounting parts Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savvy people.Installation service:We are also happy to install the display for you. Please ask.  

Replacement Hammer for RH4 KeyboardThe RealHammer 4 (RH4) keyboard is a 4 zone hammer mechanism.This Keyboard is also known as "Natural weighted Hammer Action".

 stereo rotary potentiometer for Volume, suitable forYamaha PSR-330 und 340PSR-530 bis 550PSR-630 und 640PSR-730 und 740PSR-1000, 1100, 1500PSR-2000, 2100, 3000PSR-S700 und S710PSR-S900 und S910Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 6mm. It is made of black plastic. Its head has a slot and ends in corner radius.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 1 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland JD-800 VolumeRoland XV-88 VolumeThe plastic lever must be shortened. The original potentiometer has a 5 mm sliding pin.This volume control with the labelling EWANA0X5B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVE-Mu e64We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: white Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping is eliminated)lifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in E-Mu e4:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. This part must be desoldered.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people. Installation service:We are also happy to install the display for you. Please ask.

1 pcs. FFC cable for Yamaha CVP-209 500 mm length Length = 500 mmPitch= 0,5 mmBoth sides have the same connectorThis cable is used to connect LCD Display with Mainboard inYamaha CVP-207Yamaha CVP-209Yamaha CVP-900The LCD display in the Yamaha Clavinova has vertical stripes in the display?Do you have vertical stripes in the LCD display of your electric piano? These are lines that run from top to bottom through the display and do not belong in the picture.An exchange of this FFC cable can achieve an improvement. In the best case, the vertical stripes are then completely gone. 

1 pcs Yamaha FSX Keyboard FFC cable 23 Pol 1,25Keyboard connection cableLength = 130 mmBoth sides have the same connector  

1 pcs. Kawai Round KnobKawai MP-8Kawai MP-7Kawai MP7SEKawai MP-11Technical Description of Kawai Knob:This Round knob will be put on rotary potentiometer on your Kawai Stage Pianos

1 pcs tactile switch suitable forE-mu E4K           all without   Rec,Play,Stop,RW,FWE-mu E-Synth     all without   Rec,Play,Stop,RW,FWE-Mu e6400E-Mu e4XT We offer here tact switch with softer tactile feeling than orignial ones. With this change you get switch with mutch higher life span (x10) than original fomr e-mu build in tact switch.why should I solder new pushbutton

1 pcs. OLED Display brandnew in white forRoland D-50this is  a plug in ready Display replacement for Roland D-50. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation:We deliver this OLED dislpay for the Roland D-50 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Instructions are enclosed with the display.For a detail mountint manual you can have a look here on Supersynthprojects. Please note, ouor display is ready wired:Roland D-50 mountingThe color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Roland Toggle switch, 2 pol 3 position with solder pins for PCBused inRoland Juno 106Roland Juno 60technical Dates:Termination Solder Pin3 PositionPractical advice:Knowledge in soldering is required for switch replacement.

Recapping set for Roland XV-5080 Mainboard The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.From our repair experience we know that the SMD electrolytic capacitors used in the Roland XV-5080 are now defective due to age.On the mainboard of the XV-5080 also some classic cup electrolytic capacitors have been used. These electrolytic capacitors are usually inconspicuous and intact. Manufacturer: NichiconThe set consists of 23 SMD electrolytical Capacitors.The board also uses 2 bipolar, i.e. non-polarized capacitors.This Recapping Set contains all SMD Capacitors for Mainboard recapping in Roland XV-5080.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 piece EPROM with Yamaha DX7 II OS version 1.9we offer here a  OS version for the Yamaha DX7 IIMounting instructions for the EPROM in the Yamaha DX7 II:Soldering may be required if the EPROM in the Yamaha DX7 II is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

1 pcs. Yamaha NL2 Guide CapThis rubber fits in these keyboardsYamaha GH3Yamaha NL2This rubber sits at the head of the key guides and is used for the black deeds and for the white deeds.Color: black

1 pcs. Black LCD Display with LED Backlight replacementYamaha RS7000We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display for RS7000 :Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RS7000 :To replace the display, the Yamaha RS7000 is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters.   

1 pcs Slide Potentiometer with 30mm Travel.Suitable for forRoland Jupiter 6Roand JX3PRoland SH-101       VCO Pulse Width, all Source Mixer,VCF Freq, VCF Res, Env, Kbd, Env Sustain The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs Single panel button 19 mm without LED window, for Korg PA4x Do you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive. 

Replacement keys for KAWAI Keyboard RH-88Bsuitable forKawai CN33Kawai CN34Kawai ES7Kawai MP7The Kawai RH88B keyboard is a velocity sensitive keyboard with 4-zone hammer action.4-zone hammer action:With the 4-zone hammer action, Kawai is trying to get even closer to the feel of a mechanical grand piano than was possible with the previous hammer action keyboards. The keyboard touch of a mechanical piano is different in weight depending on the zone, whether bass or in the high range. This is simulated in the Kawai RH88B keyboard by the fact that there are four different hammers with different weights.The 4-zones are divided as follows:Zone 1, Bass - note 1 to 15Zone 2, middle1 - note 16 to 32Zone 3, middle2 - note 33 to 63Zone 4, soprano - note 64 to 88 

Korg Prophecy Mainboard Recapping SetThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set consists of capacitors from renowned manufacturers. Preferably from Nichicon, Würth or Vishay. The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

2 pcs. CR2032 with solder pin suitable forYamaha SY99 Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version.Manufacturer: Panasonic or VartaPractical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Battery with solder pin suitable for  E-Mu ProteusPlease check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. EL-panel as sparepart for backlight inCasio FZ-10Casio FZ-10MCasio FZ-20MCasio VZ-1Casio VZ-10Be carefull: These backlights are very sensitive for heat. When soldering the cable necessarily make for a very good heat dissipation. 

1 pcs. CD4052BE Multiplexer, DIP16Mechanical Description:The Multiplexer is housed in a DIP 16 package and is designed for  mounting on a circuit board. The Logic Circuit has 2 x 8 connecting pins with grid of 2.54 mm x 6.6 mm.Technical Hint:Mounting of this part requiers soldering.Integrated Circuits are