Keyboards

1 pcs. Clavia Nord Drawbar Potentiometer 45mm The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. black LCD Display brandnew forYamaha TX16Wthis is  a plug in ready Display replacement for Yamaha TX16W. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours.

Hammer for a Technics E-Piano, 88 Key HammeractionThe hammers are used and in good condition. All keys supplied by us have been tested.2. different hammer versions:Please pay attention to the details. This Technics keyboard is also available with a pressure point simulation. The hammers in this keyboard version are constructed slightly differently in detail. Please take a close look.Technics has always used the same keyboard for many years. Today it has the advantage that the spare parts are easily interchangeable between the different instruments.We are of the opinion that Technics has used a very good and above all durable keyboard here. In addition to the good sound of the electric pianos, this is a definite plus point in favour of Technics electric pianosAssembly instructions:To be able to use a hammer, the keyboard must at least be unscrewed. This allows the keyboard as a whole to be pushed slightly away from the front edge. Now the key must be unscrewed. The hammer can then be removed from the top. 

1 Pc. Korg Upper Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 1 times.

1 Pc. Korg Lower Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 2 times. 

1 pcs. Encoder 12 mm footprint and extra short axis suitable for modelsKorg M3Korg OasysKorg TritonKorg Triton leKorg Triton extremeKorg Triton ProKorg Triton ProXThe original encoder used by Korg is no longer manufactured. We offer a replica here. The mechanical dimensions are identical. There are minimal deviations. The detents appear harder than on the original. Practical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Varta 3/V 150 NI-MH rechargeable with 2 solder pin suitable forKorg PolySixKorg Poly-61Varta produces two almost identical batteries of this type. The main difference is the design of the housing.Attention: Shipping for Europe only Dimensions for PCB layout: 17,7 x 10 mmTechnical Description:The dimensions of 3V/150 are hight of 26,8 mm and a deepth of 17,7 mm. The distance between the solder legs is 17,7 mm. The + pol has to legs with a distance of 10 mmThe akku is charged and ready for use.Practical tip:The akku is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Battery with 3 solder pins suitable for  Casio VZ-1Casio VZ-10M

1 pcs. LCD Display brandnew in Yellow forKorg M1this is  a plug in ready Display replacement for Korg M1. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.Not compatible with M1r. This Display is a separate item.The color of the shown display, may differ from the original.These different Display versions are available:BlueblackWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs Dial Knob suitable forRoland Fantom X6Roland Fantom X7Roalnd Fantom X8

1 pcs. Joystick  Assembly forKorg KROME 61Korg KROME 73Korg KROME 88This Joystick  unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all. 

Slide potentiometer with 30mm travel. Suitable forKorg M3Korg Kronos 61Korg Kronos 73Korg Kronos 88Korg      spare part No.: 500365011400Specifications:Resistance: 10 kOhmtravel: 30 mmTechnical description:The potentiometer has a sliding path of 30 mm. Praktical tip:The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slide switch with solder Pins for PCB mounting suitable forRoland Juno 106 - DCO,VCF,VCAtechnical Dates:Termination Solder PinSupplied without capPractical advice:Knowledge in soldering is required for switch replacement.

Power cabel 2m with 3P C13 plug   

1 pcs. Power cabel 1.5m with 2P Europlug and solderlugsPower Cord with on side open adn one side Euro PlugOriginal cable fragile or already damaged?For instruments that are 30 years and older, it makes sense to check the power cord. Has the plastic become brittle over the years or is there damage at the kinks of the cable? 

1 pcs. tactile switch suitable for modelsNord ComboNord ElectroNord LeadNord ModularNord PianoNord StageThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsCasio FZ-10MCasio FZ-20MCasio VZ-1Casio VZ-10MThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

30 g can of plastic grease for Technics keyboardswe offer here a grease that is specially made for plastic parts.Especially for Technics keyboards we have collected very good experience.This plastic grease has good creep properties that are only partially desirable for a keyboard. Please apply only very sparingly so that the grease is not deposited on the felts.Not to be used for Fatar keyboards.For moving plastic parts.

1 pcs. Slide Potentiometer with 30mm Travel. (Custom Built with dust cover for Synth-Parts)Suitable for forRoland SH-101      Lfo Rate, Lfo Mod. Env ModThese potenziometer are brand new ALPS Potentiometer. Additional benefit is a dust cover diectly mounted on housing.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slide Potentiometer 10 KOhm for  Data Entry Sequential Circuits Prophet VS KeyboardThe original fader cap is difficult to fit. The dimensions of the sliding pin differ slightly from the original.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-120Yamaha CLP-430Yamaha CLP-920Yamaha CLP-990Yamaha P-105Yamaha P-120 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

Complete Set tactile switch suitable for AKAI MPC-2500Part Number: : ES-415015J and ES-349474The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required

Recapping Set for Korg Wavestation KeyboardThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Korg Wavestation series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, from well knonw Manufacturere like Nichicon, Panasonic, Vishay or Würth.This Recapping Set contains all necessary Capacitors for Korg Wavestation.In Korg Wavestation was already used a Switching Power Supply Unit:Warnung: Schaltnetzteile speichern hohe Energien über lange Zeiträume. Hier arbeiten Sie an einer Baugruppen die mit 230 V AC und ca. 300 V DC arbeiten.Sie führen diese Arbeit auf eigens Risiko und in voller Eigenverantwortung durch.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland TB-303technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.