Keyboards

1 pcs. brand new Sequential Circuits, SCI Potentiometer 10kOhmSequential Circuits Prophet 5 REV1     Serial 1 - 182Sequential Circuits Prophet 5 REV3     Serial  from 1301 to EndSequential Circuits Prophet 10This potentiometer is only for the instruments built between 1978 and 1984.The potentiometers that were installed in the Prophet 5 and also in the Prophet 10 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 10 KOhmChanges to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread          Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.      The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Cable straight thru 12,7 x 11,7 mmThis Cable straight thru is used by 2 pol power cords.Dimensions of mounting hole: 12,7 x 11,7 mm

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo with two switch, for printed circuitThis part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Yamaha DX7Technics SX -PX20Technical descriptionThe offered phone jack for PCB mounting is a stereo jack two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Phone Jack 1/4- 6.3 mm, stereo witch Switch, for printed circuit used by  Clavia Nord PianosTechnical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Phone Jack 1/4- 6.3 mm, Mono, for printed circuit used by  Clavia Nord PianosTechnical descriptionThe offered phone jack for PCB mounting is a mono jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs Encoder EC24B50D Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs Ceramic 

Replacement keys and spare parts for Fatar TP/8S Keyboard, weightedWe would like to expressly point out that the keys are used. Fatar keys tend to darken and yellow significantly. Under certain circumstances, it may be that we currently only have very darkened keys in stock.Fatar TP/8S keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white. 

Contact rubber for Korg SK4 KeyboardContactrubber with 12 contacts are discontinued.Strip bright:   26 mmStrip height:     9.5 mmStrip length:  164 / 179   mmNumber of contacts: 12 or 13A rubber contact strip consists of 12 contacts and covers an octave. For the complete exchange of the contact strips in a keyboard with 61 keys 4 contact rubbers with 12 contacts and 1 contact rubber with 13 contacts are required.

Replacement–set for broken key guides on Technics electric pianosWith Technics electric pianos, it can happen over time that the original key guides break because of aging. This leads to a hanging or grinding of the keys. Since there are no more original spare parts for Technics, we have been looking for an alternative. Through various application tests and material research, we have found a product that fulfills the characteristics of the original Technics key guides in an identical way. Therefore we offer you a matched spare part set for your Technics piano in our store. Why we don't have the parts rebuilt?For the reproduction of a plastic part, an individually made injection mold must be produced. Due to the rather special shape of the original key guide, the effort is very high and expensive. This would drive up the final selling price dramatically and would simply not be profitable for us. But since we have tested our product extensively, we can sell our alternative with a clear conscience. So that everyone can get an impression of our product and the handling or the exchange, we have prepared a suitable blog post and a PDF variant to print out. You will also receive a printed manual with the product when you order it. Included in the set:– Matched tube suitable for a keyboard with 88 keys.– Special keyboard grease– Instruction manualWhen replacing the key guides, it is necessary to grease the new parts. For this reason, a suitable grease especially for electric pianos is included in the set. 

1 pcs. Kawai  Key Stopper Felt for E-Piano KeyboardsThis felt is used by Kawai in many keyboards and dampens the keys when they are returning to zero position. In the drawing it is the two felts with the number 34This felt consists of several layers of different materials.For better mounting this felt is equipped with an adhesive tape.  

1 pcs. Lithium Battery BR-2330Attention: Shipping for Europe only Technical Description:The dimensions of BR2330 are diameter of 23 mm and a thickness of 3 mm. Manufacturer: Panasonic or Varta Information for handling old Battery's

1 pcs. Slidepotentiometer. Suitable forAKAI MPC500AKAI MPC1000The lever (sliding pin) is here about 3 mm longer than the original. However, the pin can be shortened well with a pair of straight pliers.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

Recapping set Power Supply for Yamaha DX7 II ONLY for EU - 230VAVThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha DX II series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the power supply in the Yamaha DX7 II Spare part number of the PSU board: VB78450 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Roland MC303 and MC505 Encoder Board newThis Encoder PCB is suitable forRoland HP-557Roland MC303Roland MC505Mechanical Description of Roland MC505 Encoder Board:Roland used a Panasonic encoder with the designation EVQ-VEM-F01-24B in the above instruments. The production of this encoder at Panasonic was stopped many years ago.We have developed an adapter board on which a today's common encoder is soldered. This adapter board is soldered directly onto the Roland electronics.The switching feel is a bit harder with this new encoder than with the original.The new encoder has a metal housing and a plastic axle. Practical advice for Mounting MC303 Encoder :The encoder is permanently soldered onto a circuit board. Manual skills and experience in soldering are required for replacement. 

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland HP-136Roland HP-236Roland HP-237Attention: Lever - Slide pin must be shortende around 5 mmThis volume control with the labelling EWANNBX10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Service Kit Kawai RH88A PWB Assy KKB-034This service kit replaces the circuit boards and contact rubbers in the Kawai RH88A keyboard. Only possible as a replacement for keyboards in which contact rubbers with two contacts per tone were used.The set consists of two boards, fully equipped with new contact rubbers.These Board fit in these e-pianos:Kawai CN23Kawai CN33Kawai CN43Kawai CS3Kawai MP6

1 pcs. Alfa Rpar AS3109 VCF IC DIP16 replacement for Roland IR3109The IC Alfa Rpar AS3109 is a voltage-controlled filter module that was used in analogue synthesizers in the 1980s. The AS3109 is pin-compatible with the Roland IR3109. Mechanical Description of AS3109:This AS3109 is housed in a DIP 16 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The IC has 2 x 8 connecting pins with grid of 2.54 mm x 7.62 mm.Technical description of the AS3109:Voltage-controlled four-pole filter. The four independent sections can be connected together to enable a variety of filter responses, including common filters such as low-pass, high-pass, band-pass and all-pass. A single input exponentially controls the frequency over greater than a 15 octave range with little control voltage feedthrough. AS3109 benefits from high input impedance buffers.Pin-compatible replacement for the IR3109.Technically, the IC may differ slightly from the original. When replacing a Roland IR3109, the entire instrument must be recalibrated.The IR3109 was installed by Roland in the Jupiter series, the Juno series, the SH-101 and others, among others.Practical tips:These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Please be carefull because of static charing 

1 pcs. Encoder 16 mm widht suitable forKawai K5000 Practical advice:The thread of this encoder is 2 mm longer than the thread of the ALPS encoders. Depending on the space in the housing, it can tighten a bit when reassembling. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. LCD Display with LED Backlight replacement including cable Kit forYamaha SY77Yamaha SY99 We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Pleaase let us know your instrument, so we can put on right cable length. Benefits for this Display Replacement with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation this Display in Yamaha SY77 or SY99:The instrument must be disassembled almost completely to reach the display.  This is a very time-consuming process. Please do not underestimate the disassembly and assembly effort.This work is to be done only by technically, best electrotechnically savvy people.No soldering required.All you need is a screwdriver and a side cutter.

1 pcs. Fader knob suitable for:Korg Pa3XKorg Pa3X Pro

1 pcs. Yamaha Tyros  Speaker StandThis housing is made of plastic

BA15532 Dual Operational Amplifier with low noise for audio applicationMechanical Description:The Amplifier is housed in a SOP 8 package and is designed for SMD mounting on a circuit board. The Amp has 2 x 8 connecting pins with grid of 1.27 mm x 4.4 mm.

1 pcs. New 2,36 inch highrange speaker, replacement for Technics EAS-65PH31suitable forTechnics E-PianosTechnics KeyboardsTechnics OrgansCone tweeter with special basked for the high-frequency range above 5000 Hz.Balanced frequency response with brilliant highs and high power handling.No separate high-frequency range housing construction necessary.Suitable as replacement unit for many HiFi speakers.