Products

1 pcs. Tactile switch with black button and red LED suitable forSequential Circuits Prophet VS The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

tactile switch suitable for modelsRoland D5Roland D10Roland U220Part no: 13169684The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for models Nord ComboNord ElectroNord LeadNord ModularNord PianoNord StageThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece bipolar Elko 0.22uF/50VManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Electrolytical Capacitor 22uF/100V for Audio circuitsManufakturer: NichiconSeries: KWHere i offer spezial Capacitor from manufakturer Nichicon. The series KW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

5 pcs Contact Cleaning Stripes for electrical contacts These contact cleaning stripes are spezial developed for cleaning electrical Contacts.The strip consists of a kind of paper that is quite hard, does not fuzz and is abrasion resistant. The strip was then soaked with a special cleansing solution.

1 pcs Encoder EC24B50D Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Kawai 7 mm Felt green for E-Piano KeyboardThis felt is used by Kawai in the wooden keyboards, such as those built into the CA65. This felt sits on the front of the keyboard. For better assembly, this felt is equipped with an adhesive tape. The same felt is used in the Kawai ES1 stage piano. Here it is the hammer felt with the spare part number: 813174 

Pedal Assembly for Yamaha E-Pianos XR780On this Pedal the PCB is fittet with Ground cable.Practice tip:Yamaha has built in a socket on the boards, which are built into the pedal which is perpendicular to the board. Here, the cable is plugged in that leads to the electronics of the electric piano in the upper part. As a result, this beech breaks out in the course of the operating years and it comes to the failure of the pedal.In most Repartur cases, it will be enough just to swap the socket.Depending on the model, this pedal was supplied with a potentiometer or contact rubber in the damper pedal. Please be sure to check the pedal before ordering a replacement part. 

Replacement keys and spare parts for Fatar TP/8S Keyboard, weightedWe would like to expressly point out that the keys are used. Fatar keys tend to darken and yellow significantly. Under certain circumstances, it may be that we currently only have very darkened keys in stock.Fatar TP/8S keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white. 

Replacement keys for Fatar TP40 GH Keyboard (used) Fatar TP40 GH keyboard is a touch sensitive keyboard with 3 Zone Hammer Action.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The unweighted keys have a length of 21.5 cm and a width of 2.24 cm. The thickness of the keys is 1,5 cm.The contactor, which presses on the contact strip is 1.2 cm deep. The distance between the front contact and the front of the keyboard is 14 cm. A movable hook is hooked into this opening. 3-Zone Hammer Mechanics:A 3-zone hammer mechanism is a little bit unusal for high-quality e-piano keyboards. Normaly there will bee 4 zone hammer mechanism. By means of the three different zones the Manufacturer Fatar try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are three different hammers with different weight.The keys are in color white.The plastics used by Fatar tend to darken very strongly and the plastic becomes somewhat brittle. At the moment we have used keys in a very good condition.These keyboards are placed in the products of Doepfer (well known for their Master Keyboards and modular Synthesizer) and Waldorf.

Replacement Hammer for RH4 KeyboardThe RealHammer 4 (RH4) keyboard is a 4 zone hammer mechanism.This Keyboard is also known as "Natural weighted Hammer Action".

 stereo rotary potentiometer for Volume, suitable forYamaha PSR-330 und 340PSR-530 bis 550PSR-630 und 640PSR-730 und 740PSR-1000, 1100, 1500PSR-2000, 2100, 3000PSR-S700 und S710PSR-S900 und S910Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 6mm. It is made of black plastic. Its head has a slot and ends in corner radius.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 1 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Kawai Pedalcable No2

1 pcs. FFC cable for Yamaha CVP-209 500 mm length Length = 500 mmPitch= 0,5 mmBoth sides have the same connectorThis cable is used to connect LCD Display with Mainboard inYamaha CVP-207Yamaha CVP-209Yamaha CVP-900The LCD display in the Yamaha Clavinova has vertical stripes in the display?Do you have vertical stripes in the LCD display of your electric piano? These are lines that run from top to bottom through the display and do not belong in the picture.An exchange of this FFC cable can achieve an improvement. In the best case, the vertical stripes are then completely gone. 

1 pcs. Kawai Round KnobKawai MP-8Kawai MP-7Kawai MP7SEKawai MP-11Technical Description of Kawai Knob:This Round knob will be put on rotary potentiometer on your Kawai Stage Pianos

1 pcs tactile switch suitable forE-mu E4K           all without   Rec,Play,Stop,RW,FWE-mu E-Synth     all without   Rec,Play,Stop,RW,FWE-Mu e6400E-Mu e4XT We offer here tact switch with softer tactile feeling than orignial ones. With this change you get switch with mutch higher life span (x10) than original fomr e-mu build in tact switch.why should I solder new pushbutton

1 pcs. 26 pin FFC socket with 1.25 mm pitch right angel26 pintop contact sidePitch: 1.25 mmThis FFC Socket is used in Roland JD-800. This is located on small PCB under Keyboard

1 pcs. Yamaha NL2 Guide CapThis rubber fits in these keyboardsYamaha GH3Yamaha NL2This rubber sits at the head of the key guides and is used for the black deeds and for the white deeds.Color: black

1 pcs. Black LCD Display with LED Backlight replacementYamaha RS7000We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display for RS7000 :Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RS7000 :To replace the display, the Yamaha RS7000 is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters.   

1 pcs Single panel button 19 mm without LED window, for Korg PA4x Do you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive. 

2 pcs. CR2032 with solder pin suitable forYamaha SY99 Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version.Manufacturer: Panasonic or VartaPractical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. CD4052BE Multiplexer, DIP16Mechanical Description:The Multiplexer is housed in a DIP 16 package and is designed for  mounting on a circuit board. The Logic Circuit has 2 x 8 connecting pins with grid of 2.54 mm x 6.6 mm.Technical Hint:Mounting of this part requiers soldering.Integrated Circuits are  

1 pcs. Cable straight thru 12,7 x 11,7 mmThis Cable straight thru is used by 2 pol power cords.Dimensions of mounting hole: 12,7 x 11,7 mm