Products

1 piece Elko 220uF/35V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      A,D,S,R,LFOElectrical properties:The nominal resistance has 100 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      LFO Rate, DCO LFO,SUB OSC, NOISERoland Juno 60    LFO-RateElectrical properties:The nominal resistance has 50 KOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Kurzweil K2000 VOL/DATA Assembly NEWKurzweil K2000There is a difference to original volume slider: The original volume slider has a logarithmic characteristic, here a linear characteristic was used for the volume slider.This completely assembled and mounted PCB is manufactured by ReBach from the Netherlands and is a 1: 1 replica of the original Kurzweil board. 

1 pcs. Yamaha GHD A88 Keyboard complete--- shipping only in germany, sorry  -----Please ask if this keyboard is the right one for your e-piano model.This keyboard was used for many years in the vast majority of Yamaha electric piano models.The replacement of the entire keyboard is from a certain age of the electric piano well worth considering.For example, if your original keyboard is affected by the grease problem, you have here an alternative after desen exchange you no longer have to worry about the keyboard.If the keyboard is not in stock, we can order the keyboard from Yamaha. There may be a delivery time.

1 pcs. black LCD Display with LED Backlight replacement for ALESIS Andromeda We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color:  white Character / black BackgroundDelivery scope:Display ready wiredMounting parts Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savvy people.Installation service:We are also happy to install the display for you. Please ask.  

1 pcs. new Contactrubber for Yamaha GHL KeyboardThis keyboard is used in these modells:Yamaha P-35Yamaha P-70Yamaha P-105Yamaha AriusYamaha MOXD8Yamaha MOXF8Color of these Contactrubber may be different.

1 pcs. Button largeKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of  mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. Yamaha contact PCB for Yamaha GHL88 KeyboardThis keyboard is used inYamaha P-115Yamaha P-125Yamaha YDP-S30Yamaha YDP-143

Replacement Keys for Yamaha GH3 GKS KeyboardThese Keys fits for all Yamaha GH3 GKS keyboards.Yamaha GH3 GKS keyboard is used in:Yamaha Clavinova CLP-440Yamaha Clavinova CLP-525Yamaha Clavinova CLP-625Yamaha Clavinova CLP-635Yamaha Clavinova CVP-605Yamaha Clavinova CVP-701Note on the keys supplied:The keys are manufactured in two different production facilities at Yamaha. Depending on the production of the keys, they have different features. One variant is supplied with black rubber, the other variant without black rubber. In the second case the black rubber has to be taken over from the old key. The key with rubber also has a small fat reservoir. The Yamaha GH3 keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVE-Mu e64We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: white Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping is eliminated)lifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in E-Mu e4:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. This part must be desoldered.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people. Installation service:We are also happy to install the display for you. Please ask.

1 piece Elko 3,300uF/50V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs Yamaha FSX Keyboard FFC cable 23 Pol 1,25Keyboard connection cableLength = 130 mmBoth sides have the same connector  

1 pcs. Kawai  Key Stopper Felt for E-Piano KeyboardsThis felt is used by Kawai in many keyboards and dampens the keys when they are pushed For better mounting this felt is equipped with an adhesive tape.  

1 piece EPROM with Yamaha DX7 II OS version 1.9we offer here a  OS version for the Yamaha DX7 IIMounting instructions for the EPROM in the Yamaha DX7 II:Soldering may be required if the EPROM in the Yamaha DX7 II is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

Replacement keys for KAWAI Keyboard RH-88Bsuitable forKawai CN33Kawai CN34Kawai ES7Kawai MP7The Kawai RH88B keyboard is a velocity sensitive keyboard with 4-zone hammer action.4-zone hammer action:With the 4-zone hammer action, Kawai is trying to get even closer to the feel of a mechanical grand piano than was possible with the previous hammer action keyboards. The keyboard touch of a mechanical piano is different in weight depending on the zone, whether bass or in the high range. This is simulated in the Kawai RH88B keyboard by the fact that there are four different hammers with different weights.The 4-zones are divided as follows:Zone 1, Bass - note 1 to 15Zone 2, middle1 - note 16 to 32Zone 3, middle2 - note 33 to 63Zone 4, soprano - note 64 to 88 

1 piece Electrolytic Capacitor 220uF/16V for Switching Power SupplyManufakturer: NichiconHere i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Battery with solder pin suitable for  E-Mu ProteusPlease check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Encoder 16 mm widht suitable forKawai K5000 Practical advice:The thread of this encoder is 2 mm longer than the thread of the ALPS encoders. Depending on the space in the housing, it can tighten a bit when reassembling. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. EL-panel as sparepart for backlight inCasio FZ-10Casio FZ-10MCasio FZ-20MCasio VZ-1Casio VZ-10Be carefull: These backlights are very sensitive for heat. When soldering the cable necessarily make for a very good heat dissipation. 

Knob for rotary potentiometers inKorg ESX-1 SDSpecifications:Diameter top:        9.4 mmDiameter bottom: 12.0 mmHight:   14.7 mmShaft:   6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

1 pcs. Yamaha Tyros  Speaker StandThis housing is made of plastic

1 pcs. new Slide potentiometer with 30mm travel and 15mm Lever. Suitable Slider for Yamaha CS-15    - EG-SYamaha CS-30    - EG1, EG2, EG3Yamaha CS-40    - Sustain  Electrical properties:The nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint:The Lever of the original potentiometer has a conical, tapering shape.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo with two switch, for printed circuitThis part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Yamaha DX7Technics SX -PX20Technical descriptionThe offered phone jack for PCB mounting is a stereo jack two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.