Keyboard

1 pcs. new Korg RH-4L PCB Assy KeyboardRH-4, RH-4L or RH-4HL—one letter—big difference. Please note.this is set of three contact PCB as used in Korg RH-4L.This set contains LOW, MID ans HIGH contact PCB  - KLM 3587/88/89, 510d929735The circuit board is partially supplied with a blue protective film over the contacts. This protective film must be removed before installation. 

1 pcs. Fatar TP100 replacement keys whiteThe Fatar TP100 keyboard is a velocity-sensitive keyboard with hammer action.The keys are mounted on a support frame with a plastic core. Contact is made via 12-pin rubber contact strips with two or three graphite points.The unweighted keys are 19.5 cm long and 2.24 cm wide. The key is 1.5 cm thick. The upper resting point on this keyboard is achieved by a hook moulded into the back of the key. The contact actuator, which presses against the contact strip, is 0.2 cm deep. The distance between the contact actuator and the front of the key is 13 cm. At the end, the key tapers into a narrow web. A notch with a round opening is cut into this web. This notch is used to snap the key into the keyboard frame.The hammer, which acts as a counterweight beneath the key, is also hooked into the key. For this purpose, the key has a downward-facing stage. This stage is 47 mm deep from the top edge of the key.Removing and fitting a key:A key is removed by pulling it forwards with moderate force. The key clicks audibly out of the frame.A key is fitted into the frame by snapping it into place with moderate force.This secures the key at the rear end.The keys are white in colour.The plastics used by Fatar tend to darken significantly over time and the plastic becomes somewhat brittle. We currently have second-hand keys in very good condition available.This keyboard is used in products by, amongst others, Doepfer (known for master keyboards and modular synthesisers), Clavia Nord and Waldorf.The keys can be used with double or triple contact rubbers. 

Replacement keys, weighted for Fatar TP/8+ KeyboardFatar TP/8+ keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points. The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked. The keys are in color cream white.

1 pcs connection cable for your Roland PHA KeyboardThis Cable connects the Low, Mid and High Boards with the Mainborad of your Roland PHA Keyboard.Contacts:  16PPitch:       1,25 mmLength:     90 mm 

Contact rubber for Fatar Keyboards build in in Roland Key InstrumentsRoland used in different Instruments Keyboards from Manufacturer Fatar. In this Keyboards are build in Contact rubber that is different to normal Fatar Contact Rubber.These Contact Rubber fits only in Fatar Keyboards used in Roland Instruments:Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP10 MDRFatar TP10 ABSFatar TP40technichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white 

Contactrubber for Roland SK8 KeyboardRoland SK8 Keyboard is used inRoland JV-80Roland JV-90Roland JX-30Roland JX-35Roland JX-50Roland XP-30Roland XP-50Roland XP-60Attention: This blue contactubber do not fit in old SK8 Keyboards  

Parts for Roland SK9 KeyboardsHere you will find all parts like springs, felt, aftertouch and P.C.B.

Hammer for Roland Progressive Hammer Action Keyboard- PHA2 and PHA3Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107e

1 pcs. Replacement Keys for Technics KeyboardsThis Keyboard with single Keys is used by Technics in many of there Keyboards.These Keys are unweigted and in Color Pure white.This parts are used and in a good condition.Important NOTE:For this Keyboard Version Tehnics used different P.C.B.'s and differernt Contactrubber. Please have a exact look on your Keyboard if you need a replacement P.C.B or replacement Contactrubber.

1 pcs. Diode Keyboard Matrix Kawai 

Contact rubber Version 2 for Technics KeyboardThis contact rubber version is run without any maintenance bumps. The contact rubber is held in a special frame.For the complete exchange of the contact strips in a keyboard with 61 keys 9 contact rubbers with 6 contacts and 1 contact rubber with 7 contacts are required.Contact high:  12 mmStrip bright:   15 mmStrip length:  82 / 94   mmNumber of contacts: 6 or 7

Replacement Hammer for TP40GH KeyboardThe TP40 GH (graded hammer action) keyboard is a 3 zone hammer mechanism.

Replacement Keys for Korg Pa50Color: whitemechanical construction:Keys for this Keyboard are not available as single keys. One Octave will be a set of three single spare parts. One part for the black Keys. One part for D/A/F, and one part for C/E/F/B.

NEW Replacement Keys, weighted for Roland SK8 Synthesizer Keyboardused inRoland XP-30Roalnd XP-80This are new Key's without "Red Glue-Problem" 

Replacement keys and spare parts for Fatar TP/9 KeyboardActual Keys in stock are strong darkened. Please refer the Photo.Fatar TP/9 keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 16 cm and a width of 2.24 cm. The thickness of the keys is 1 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 8,5 mm. The distance from the front side of the key is 11 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white. 

Replacement Keys for Roland Progressive Hammer Action Keyboard- PHA2Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107eColor/tint: creme white (ivory)

Key's for a Technics E-Piano, 88 Key HammeractionThe keys are used and in good condition. All keys supplied by us have been cleaned and checked.Since these are used keys, color deviations may occur. Technics has always used the same keyboard for many years. We think Technics has used a very good and above all durable keyboard.

1 pcs.  key contact board suitable FS keyboardsThis key contact is usedWidth: 6 cmheigh: 1,4 cmContact Resitance: lower 1 Ohm

Replacement Keys, weighted for Roland SK8-P Keyboardused inRoland KR-650Note: This keyboard has the problem that the glue for the key weights does not fully cure. This causes the glue to "flow" and the key weights to fall out. Never store instruments with this problem upright. Then the glue flows over all the keys and glues them together. This is the so-called "red glue problem". We currently have buttons with triggered weights that we add separately in stock. 

Replacement keys for Fatar TP/30 Keyboard Fatar TP/30 keyboard is a touch sensitive keyboard with Hammer Action. Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine. contact detection is done via 12 pin contact rubber strip with two graphite points.The unweighted keys have a length of 21.4 cm and a width of 2.24 cm. The thickness of the keys is 1,5 cm.The contactor, which presses on the contact strip is 2.8 cm deep. The distance between the front contact and the front of the keyboard is 14 cm. The keys are in color white.The plastics used by Fatar tend to darken very strongly and the plastic becomes somewhat brittle.

1 pcs. Contact rubber forKorg Pa500Korg X50This are brand new contact rubbers.A contact rubber consists of 12 or 13 contacts and covers an octave. A rubber contact strip consists of 12 or 13 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 61 keys you will need 4 contact rubber with 12 contacts and 1 contact rubber with 13 contacts.

Contact rubber Version 1 for Technics KeyboardThis contact rubber version is run without any maintenance bumps. The contact rubber is held in a special frame.For the complete exchange of the contact strips in a keyboard with 61 keys 4 contact rubbers with 12 contacts and 1 contact rubber with 13 contacts are required.Contact high:  9.5 mmStrip bright:   26 mmStrip length:  164 / 179   mmNumber of contacts: 12 or 13A rubber contact strip consists of 12 or 13 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 61 keys you will need 4 contact rubber with 12 contacts and 1 contact rubber with 13 contacts.

1 pcs. Contactrubber PSR1 suitable for Yamaha This contact rubber was only used in very, very few models. Please check your instrument first to see if it is the right rubber.

Spare parts for Kawai RF-88 Keyboard Here you will find different parts for Kawai RF-88 Keboard. Cusion, FeltHammerKey Guide