Keyboard

Replacement keys for Roland SK7 Piano KeyboardRoland SK7 Piano Keyboard is used inRoland EP-5 

Parts for Fatar TP10 KeyboardsHere you will find springs, felts, P.C.B., screws

1 piece Yamaha lower key strike felt for electric piano keyboardsThis felt is used by Yamaha in the 16L keyboard, as found in the PSR-3000, for example. This felt is located at the front of the keyboard.For easier installation, this felt is equipped with adhesive tape.The felt is designed for a 61-key keyboard. 

1 pcs. Fatar TP100 replacement keys whiteThe Fatar TP100 keyboard is a velocity-sensitive keyboard with hammer action.The keys are mounted on a support frame with a plastic core. Contact is made via 12-pin rubber contact strips with two or three graphite points.The unweighted keys are 19.5 cm long and 2.24 cm wide. The key is 1.5 cm thick. The upper resting point on this keyboard is achieved by a hook moulded into the back of the key. The contact actuator, which presses against the contact strip, is 0.2 cm deep. The distance between the contact actuator and the front of the key is 13 cm. At the end, the key tapers into a narrow web. A notch with a round opening is cut into this web. This notch is used to snap the key into the keyboard frame.The hammer, which acts as a counterweight beneath the key, is also hooked into the key. For this purpose, the key has a downward-facing stage. This stage is 47 mm deep from the top edge of the key.Removing and fitting a key:A key is removed by pulling it forwards with moderate force. The key clicks audibly out of the frame.A key is fitted into the frame by snapping it into place with moderate force.This secures the key at the rear end.The keys are white in colour.The plastics used by Fatar tend to darken significantly over time and the plastic becomes somewhat brittle. We currently have second-hand keys in very good condition available.This keyboard is used in products by, amongst others, Doepfer (known for master keyboards and modular synthesisers), Clavia Nord and Waldorf.The keys can be used with double or triple contact rubbers. 

1 pcs. Felt for Yamaha FS Keyboard Key Stopper Felt CappuchinoThe key felt on many older digital pianos, keyboards and synthesisers has started to show its age. As a result, the keyboard can become very noisy when played. The keyboard is rattling.This felt has a high density, which gives it a high degree of strength. This strength makes the felt very durable and robust. However, its ability to dampen mechanical noise is slightly lower.Fitting a new felt pad will solve this problem. A simple but effective solution.We have had this felt pad specially made by a company that specialises in the manufacture and processing of a wide variety of felts. You will receive a high-quality piano felt pad of the very best standard. Made in Germany. You will need one for a complete Keyboard with 88 keys.The felt can be trimmed for keyboards with fewer keys.One-sided self-adhering 

Replacement Keys for Korg X50 KeyboardKEY ASSY 13(M) KOC-H30306-1Color: white mechanical construction: This Keys are only available as complete set for one Octave. There is one part for a middle Octave, one part for the first and one part for the last Octave.

Replacement Keys for RH4 KeyboardRH4 keyboard is used in Korg SP-170Korg SP-280Krome 88 Color: whiteThe RealHammer 4 keyboard (RH4) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 22.8 cm with a width of 2.24 cm. The depth of the key is 4.5 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is formed downside the key. The Contactor is 11 cm from the front. At the back end, the keys are connected with other keys over a bridge. These keys are only available as complete set for a Octave.4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful. This Keys are only available as complete set for one Octave. There is one part for a middle Octave, one part for the first and one part for the last Octave.

Hammer for Roland Progressive Hammer Action Keyboard- PHA2 and PHA3Roland PHA Keyboard is used inRoland Fantom X8Roland HP-107e

NEW Replacement Keys, weighted for Roland SK8 Synthesizer Keyboardused inRoland XP-30Roalnd XP-80This are new Key's without "Red Glue-Problem" 

Replacement keys, weighted for Fatar TP10 Keyboard with pressure point Fatar TP10 keyboard is a touch sensitive keyboard with Hammer Action. The weighted Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.A pressure point simulation is entered in the keyboard variant. This is done by means of a nose formed on the Key, which protrudes downwards into the keyboard frame. The weighted keys have a length of 21.8 cm and a width of 2.24 cm. The thickness of the keys is 1,5 cm.The contactor, which presses on the contact strip is 2.8 cm deep. The distance between the front contact and the front of the keyboard is 14 cm. The keys are in color cream white.The plastics used by Fatar tend to darken very strongly and the plastic becomes somewhat brittle.

Replacement keys for Fatar TP/9P E-Piano Keyboardused inRoland A-30Roland A-33Roland A-37 Fatar TP/9P keyboard is a touch sensitive keyboard. Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 16 cm and a width of 2.24 cm. The thickness of the keys is 1 cm.The contactor, which presses on the contact strip is 1.9 cm deep. The distance between the front contact and the front of the keyboard is 10,5 cm. The keys are in color cream white.Comment:We know three different Version of this Keyboard: TP/9S, TP/9P and TP/9+. Please have a exact look at the pictures. The plastics used by Fatar tend to darken very strongly and the plastic becomes somewhat brittle.

1 pcs. Contact rubber SK30 for Technics Keyboard - diskontinued -used in:Technics KN-720Technics KN-920Technics KN-930Technics KN-1400Technics KN-1500Technics KN-1600Technics KN-2400Technics KN-2600This are brand new contact rubbers.A contact rubber consists of 12 or 13 contacts and covers an octave. A rubber contact strip consists of 12 or 13 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 61 keys you will need 4 contact rubber with 12 contacts and 1 contact rubber with 13 contacts.

Replacement Keys for Technics KeyboardsThis Keyboard with single Keys is used by Technics in many of there Keyboards.These Keys are unweigted and in Color Creme White also called Ivory.This parts are usedImportant NOTE:For this Keyboard Version Tehnics used different P.C.B.'s and differernt Contactrubber. Please have a exact look on your Keyboard if you need a replacement P.C.B or replacement Contactrubber.

Key's 16N-W Style suitable for Yamaha This keyboard is used in these modells:Yamaha MOX6Yamaha Tyros 1Color: whiteThe white Keys are weighted.The black keys are unweighted.This key is newmechanical construction:Keys for this Keyboard are not available as single keys. One Octave will be a set of three single spare parts. One part for the black Keys. One part for D/A/F, and one part for C/E/F/B.

Keys, weighted for Roland SK9 KeyboardThis part fits for all Roland SK9 KeyboardsRoland SK9 Keyboard is used inFantom (FA76)Fantom G6, G7Fantom SFantom X6, X7XP-10Color/tint: pure white 

Parts for Roland SK8-P KeyboardHere you will find used parts like contact Rubber, Frames for Contact Rubber, Springs and Keyboard Circuit Boards.

1 pcs. new Korg LS88 PCB Assy KeyboardThis keyboard is used inKorg Kronos 2 LS88this is set of three contact PCB as used in Korg Kronos 2 LS88.This set contains LOW, MID ans HIGH contact PCB.This Set is KLM-3543, KLM-3544, KLM-3545. 

1 pcs. Yamaha contact PCB for Yamaha NW GKS KeyboardThis keyboard is used in Yamaha CLP-545Yamaha CLP-575Yamaha CLP-585Yamaha CLP-645Yamaha CSP-170Yamaha CVP-609Yamaha CVP-705Yamaha CVP-709Yamaha CP4STAGEYamaha H01Yamaha R01Yamaha P515The contact board for a complete keyboard with 88 keys is divided into three parts. There is a LOW, MID and HIGH PCB board. 

1 pcs. black Replacement Keys for Yamaha GH3 GKS AI KeyboardThis black key has a roughened surfaceNote on the keys supplied:The keys are manufactured in two different production facilities at Yamaha. Depending on the production of the keys, they have different features. One variant is supplied with black rubber, the other variant without black rubber. In the second case the black rubber has to be taken over from the old key. The key with rubber also has a small fat reservoir. The Yamaha GH3 keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs. Yamaha FSX Stopper U 61This FSX keyboard is used in these modells and others:Yamaha Motif XS6Yamaha Tyros 2Yamaha Tyros 3Yamaha Tyros 4   

1 pcs. Yamaha contact PCB for Yamaha NL4 3M KeyboardThis keyboard is used inYamaha CLP-675Yamaha CLP-685The contact board for a complete keyboard with 88 keys is divided into three parts. There is a LOW, MID and HIGH PCB board. 

1 pcs. Yamaha GH3 GKS A88 Keyboard completeThis keyboard is used in these modells:Yamaha CLP-170Yamaha CLP-230Yamaha CLP-265GPYamaha CLP-270Yamaha CLP-430Yamaha CLP-465GPColor: cremewhiteShipping only with UPS and within Germany. Sorry. 

Fatar TP/8P Keyboard, Replacement keys semi weighted ivory Fatar TP/8P keyboard is a touch sensitive Pianokeyboard with semi weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The semi weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 11 mm. The distance from the front side of the key is 12,5 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white. 

Key's 16N unweighted suitable for Yamaha This keyboard is used in these modells:Yamaha PSR-e403Color: whiteThis key is newmechanical construction:Keys for this Keyboard are not available as single keys. One Octave will be a set of three single spare parts. One part for the black Keys. One part for D/A/F, and one part for C/E/F/B.