Products

30 g can of plastic grease for Technics keyboardswe offer here a grease that is specially made for plastic parts.Especially for Technics keyboards we have collected very good experience.This plastic grease has good creep properties that are only partially desirable for a keyboard. Please apply only very sparingly so that the grease is not deposited on the felts.Not to be used for Fatar keyboards.For moving plastic parts.

1 pcs. Slide Potentiometer 10 KOhm for  Data Entry Sequential Circuits Prophet VS KeyboardThe original fader cap is difficult to fit. The dimensions of the sliding pin differ slightly from the original.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Encoder 22 mm suitable forNord NordStage 2  - Main DialPractical advice:The encoders offered here come from the same manufacturer as those used by Nord. There are compared to the original small deviations in design:Pin distance here is 2.5 mm compared to 5 mm for the originalOriginal encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases at Nord and can be removed. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-120Yamaha CLP-430Yamaha CLP-920Yamaha CLP-990Yamaha P-105Yamaha P-120 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

Dual Operational Amplifier 4570 with low noise for audio applicationMechanical Description:The Amplifier is housed in a SOP 8 package and is designed for SMD mounting on a circuit board. The Amp has 2 x 8 connecting pins with grid of 1.27 mm x 4.4 mm. 

1 pcs. 2SA970Transistor 2SA970PNP Small Signal TransistorHousing print: A970Housing: TO-92PNPVebo: -5VVcbo: -120VIc:    -100mA

Recapping Set for Korg Wavestation KeyboardThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Korg Wavestation series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, from well knonw Manufacturere like Nichicon, Panasonic, Vishay or Würth.This Recapping Set contains all necessary Capacitors for Korg Wavestation.In Korg Wavestation was already used a Switching Power Supply Unit:Warnung: Schaltnetzteile speichern hohe Energien über lange Zeiträume. Hier arbeiten Sie an einer Baugruppen die mit 230 V AC und ca. 300 V DC arbeiten.Sie führen diese Arbeit auf eigens Risiko und in voller Eigenverantwortung durch.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland TB-303technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

LCD Display with LED Backlight replacement including cable Kit forKawai K5000 We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionThis Display fits inNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Yamaha USB Socket Typ B PCBJalco used by: Yamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 pcs. Yamaha USB Socket Typ A PCBJalco YKF45-0021used by: Yamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 piece Electrolytical Capacitor 68uF/400V for Switching Power SupplyManufakturer: Nichicon Here i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Recapping set forE-Mu Proteus 1E-Mu Proteus 2E-Mu ProcussionThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.This Recapping Set contains all necessary Capacitors for Switching Power Supply and Mainboard. Warning PSU Recapping:Risk of electric shock:Switching power supplys store high voltage and high energy for a very long period of time.When working with these spare parts offered here, you are working directly in a 230VAC circuit.Observe polarity. Incorrect installation will cause explosion and fire.For experts only: Be aware of dangers of electric current  

Replacement Keys, weighted for Korg SK4 KeyboardColor: pure whiteThe Korg SK4 Keyboard is a touch-sensitive keyboard with weighted Keys.The weighted keys have a length of 15.5 cm with a width of 2.24 cm. The depth of the key is 3.5 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is from the front 10 cm. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping. 

1 pcs. triple MIDI DIN socket female 5 pin for printed circuit - Roland MIDI3-NSJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. The original MIDI jack in your instrument will certainly look somewhat different. Today's possible replacement of this 3-way MIDI jack looks slightly different, but is identical in function.  used by:Roland These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. 14 pin FFC socket with 1.25 mm pitch14 pinPitch: 1.25 mmLength: 21,05 mmdeepth:  4,80 mmhight:      7,80 mmTechnical descriptionPraktikal tip:In these socket the cable cable have just to be pluged in.

1 pcs. OLED Display New forCasio CZ-1Casio CZ-101Casio CZ-1000Casio CZ-2000SCasio CZ-2600SCasio CZ-3000Casio CZ-5000The display has been prepared by us ready to plug in. We supply the display ready with the cable fitted for replacement in the synthesiser. All you need for this replacement is a screwdriver.Note on special characters: Casio uses special characters in the display of various instruments, e.g. note symbols. These symbols cannot be shown on the OLED display.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. OLED Display New forYamaha DX21This Display replacement is a really easy swapping. You will only need a screwdriver.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

Brand new OLED Display, blue, forKurzweil K1200 Pro 1Brand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1200 Pro 1 Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

1 pcs. Yamaha DC-IN PCB X9480For Europe only: 12VDC

1 pcs. Floppy2USB Adapter suitable for Yamaha SY-77Yamaha SY-99 

Yamaha GHL Key's  This keyboard is used in these modells:Yamaha P-120Yamaha P-125Yamaha YDP-S30Yamaha YDP-143Color: whiteNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.mechanical construction:Keys for this Keyboard are not available as single keys. One Octave will be a set of three single spare parts. One part for the black Keys. One part for D/A/F, and one part for C/E/F/B.

1 pcs. Rotary Potentiometer suitable forYamaha N1 Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 9.5 x 11 mm, the total length without pins is 29 mm. In this total length the casing is 16 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 10 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of brass. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The nine solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The pins, which are sticking out  are necessary for the electrical function. Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs new LCD Display with LED Backlight replacement including cable Kit forKorg WavestationKorg Wavestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument. Please let us know your instrument. Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people.