Products

1 pcs. Replacement rotary potentiometer suitable forTechnics PC-25 Volume Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Yamaha FSX  Keyboard contact PCBThis PCB is used inYamaha Tyros 2Yamaha Tyros 3Yamaha Tyros 4

1 pcs. OLED Display brandnew in white forWaldorf Microwave IIthis is a plug in ready Display replacement for Waldorf Microwave II .Soldering is requiredNotes on installation:We deliver this OLED dislpay for the Waldorf Microwave 2 synthesizer ready for installation. All cables are ready mounted.The original display in the Waldorf Microwave 2 is soldered on both sides of the cable. To replace the display, the old cable connection must be desoldered.- Instructions are enclosed with the display.Advantages of our OLED Display Set for the Waldorf Microwave 2:An OLED display is very easy to read from all sides, even at an extreme viewing angle. In addition, we supply mounting material with which the display it even closer to the display cover. This improves the readability from a steep angle even more.We supply the display with a detachable plug connection.The color of the shown display, may differ from the original.Installation service for Waldorf Microwave 2:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Yamaha NL4 Stopper U88 UpperThis GH3 keyboard is used in these modells and others:Yamaha CLP-685  

LCD Display with LED Backlight replacement including cable Kit forKorg 01R/WWe offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01R/W:The instrument must be disassembled almost completely to reach the display.The rack version of the Korg 01/RW synthesizer has much less mechanical effort than the keyboard versions.For the new display to work, one SMD resistor on the mainboard of the Korg 01/RW must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/RW have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people. 

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 00Roland D-70, mainboard version 01We offer here a high quality replacement display with modern LED technology for the backlight.Color: white font/black backgroundScope of delivery:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description!Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly for LCD Display in Roland D70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", or "02". 

1 piece Kawai Pedalcable No3Pedal cable with plug for various Kawai electric piano models. The cable fits for GFP3 pedal.The cable has a 6 pin Din connector on one side and a 7 pin flat connector on the other side.

1 pcs. Korg PA1X, PA2X Volume Slide PotentiometerKorg PA1XKorg PA2XKorg Pa50Korg Pa60Korg Pa80OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs Yamaha Contactrubber 88P newThis contact rubber was installed in different Yamaha keyboards and there are different spare part numbers for this spare part.A note about the contact rubbers: The contact rubber for the 88's keyboard was available in the colors pink and green. The pink contact rubber is missing 2 holes in the rubber which serve as a guide.The green version is no longer available.Note for the installation of the Yamaha contact rubber:Please pay attention to the installation position! The interruptions in the Konaktstreifen are not symmetrical. 

1 pcs. Nch Power MOSFET FQP2N90 - Replacement for 2SK1199 Housing:  TO220VDss:      900VId:          2.2APd:          85WTechnical hint:suitable replacement for PSU in Korg T1,T2,T3 

1 piece Elko 2,200uF/25V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs Yamaha contactrubber Wood key 12 contactsIn this wooden keyboard installed by Yamaha only in very few models, a contact rubber was used in two places.Once there is a contact rubber in the front under the wooden keys. A second Kontaktugmmi sits in the back under the hammers.Here it is the contact rubber at the front under the keys. No more rubbers available.Contactrubber for one actave with 12 contacts.Only some few parts availableThis rubber was used inYamaha CLP-175Yamaha CLP-990Yamaha CVP-900

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inRoland D-110Electrical properties:The stereo nominal resistance has 50 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 9,5 mm, the total length without pins is 24 mm. In this total length the casing is 7 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch). Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Replacement Keys for Yamaha NL2 AI CW KeyboardThese Keys fits for all Yamaha NL2 AI CW keyboards.Yamaha NL2 AI CW keyboard is used in:Yamaha CLP-585Yamaha CVP-709Note on the keys supplied:The keys are delivered without the black rubber that is mounted at the bottom of the key. The black rubber is taken from the old key. The rubber is clicked in and can be easily replaced. The Yamaha NL2 keyboard is a velocity-sensitive keyboard. The keys have a wooden core that is covered with plastic.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs. Yamaha DX7 II OLED Display NEW yellowReady-to-plug prepared OLED display for replacement in Yamaha DX7 II. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Mechanical hints for the replacement of the OLED display in the Yamaha DX7II:Please consider in this case that the mechanical effort to get to the display in the instrument is quite high. Among other things, the keyboard and the mainboard must be disassembled. Everything is screwed. No soldering necessary.The display has a cover made of Plexiglass which is glued on the display and has to be transferred to the new display. We have had good experience with the following method: Insert fishing line or sturdy sewing yarn between the display and the cover and use a sawing motion to separate the adhesive.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha NL4 Stopper U88 LowerThis NL4 keyboard is used in these modells and others:Yamaha CLP-675Yamaha CLP-685Yamaha CLP-775  

1 pcs Yamaha FUSTB AC-IN Board

1 piece Electrolytical Capacitor 4.7uF/63VManufakturer: Würth Electronic  The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. new Korg RH4 PCB Assy KeyboardThis keyboard is used inKorg Krome 88Korg SP-280RH-4, RH-4L or RH-4HL—one letter—big difference. Please note.this is set of three contact PCB as used in Korg RH-4.This set contains LOW, MID ans HIGH contact PCB  - KLM-2949/2950/2951 The circuit board is partially supplied with a blue protective film over the contacts. This protective film must be removed before installation. 

1 pcs. Korg M1R OLED Display brandnew in white this is  a plug in ready OLED Display replacement for Korg M1R Rack Synthsizer. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.To install this OLED replacement display in the Korg M1R, first remove the housing cover of the synthesiser. The front panel is then removed. The display is now accessible and can be unscrewed. When mounting the new OLED display in the Korg M1, please use the spacer sleeves supplied.Not compatible with Korg M1 Keyboard version. This Display is a separate item.The color of the shown display, may differ from the original.Installation service for Korg M1R:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs 45W internal Switching Power Supply Unit suitable forKorg SV1Electrical properties:Primary input voltage: 90 - 264 VACRated Power: 45 WattEfficiency: 77%Ripple: 1%Tripple OutputShort circuit protectionEN6100 proofEMC: CLASS BPractical advice:Plug of the device. Don't work under Voltage.  

1 pcs. PUSH SWITCH SPPH23 HQ SerieSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.