Products

1 pcs. Power cabel 1.5m with 2P Europlug and solderlugsPower Cord with on side open adn one side Euro PlugOriginal cable fragile or already damaged?For instruments that are 30 years and older, it makes sense to check the power cord. Has the plastic become brittle over the years or is there damage at the kinks of the cable? 

1 pcs. tactile switch suitable for modelsNord ComboNord ElectroNord LeadNord ModularNord PianoNord StageThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsCasio FZ-10MCasio FZ-20MCasio VZ-1Casio VZ-10MThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece Electrolytical Capacitor 4700uF/25V for Audio circuitsManufakturer: NichiconSeries: LKS - Snap InHere i offer spezial Capacitor from manufakturer Nichicon. The series LKS is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Gold-Cap 1 F/5,5 V Manufakturer: Elna or Panasonic  

1 piece bipolar Elko22uF/50V for Speaker NetworksManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The DB series is developt spezial for use in Speaker Networks. Spezial benefit is radial construstion.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Electrolytical Capacitor 100uF/63V for Switching Power SupplyManufakturer: Nichicon Here i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Elko 2,200uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Electrolytical Capacitor 3300uF/35V for Audio circuitsManufakturer: NichiconSeries: KWHere i offer spezial Capacitor from manufakturer Nichicon. The series KW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Electrolytical Capacitor 4,7uF/50V SMD Manufakturer: Nichicon The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

30 g can of plastic grease for Technics keyboardswe offer here a grease that is specially made for plastic parts.Especially for Technics keyboards we have collected very good experience.This plastic grease has good creep properties that are only partially desirable for a keyboard. Please apply only very sparingly so that the grease is not deposited on the felts.Not to be used for Fatar keyboards.For moving plastic parts.

1 pcs. Slide Potentiometer with 30mm Travel. (Custom Built with dust cover for Synth-Parts)Suitable for forRoland SH-101      Lfo Rate, Lfo Mod. Env ModThese potenziometer are brand new ALPS Potentiometer. Additional benefit is a dust cover diectly mounted on housing.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slide Potentiometer 10 KOhm for  Data Entry Sequential Circuits Prophet VS KeyboardThe original fader cap is difficult to fit. The dimensions of the sliding pin differ slightly from the original.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-120Yamaha CLP-430Yamaha CLP-920Yamaha CLP-990Yamaha P-105Yamaha P-120 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

Dual Operational Amplifier 4570 with low noise for audio applicationMechanical Description:The Amplifier is housed in a SOP 8 package and is designed for SMD mounting on a circuit board. The Amp has 2 x 8 connecting pins with grid of 1.27 mm x 4.4 mm. 

1 pcs. 2SA970Transistor 2SA970PNP Small Signal TransistorHousing print: A970Housing: TO-92PNPVebo: -5VVcbo: -120VIc:    -100mA

Complete Set tactile switch suitable for AKAI MPC-2500Part Number: : ES-415015J and ES-349474The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required

Recapping Set for Korg Wavestation KeyboardThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Korg Wavestation series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, from well knonw Manufacturere like Nichicon, Panasonic, Vishay or Würth.This Recapping Set contains all necessary Capacitors for Korg Wavestation.In Korg Wavestation was already used a Switching Power Supply Unit:Warnung: Schaltnetzteile speichern hohe Energien über lange Zeiträume. Hier arbeiten Sie an einer Baugruppen die mit 230 V AC und ca. 300 V DC arbeiten.Sie führen diese Arbeit auf eigens Risiko und in voller Eigenverantwortung durch.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

LCD Display with LED Backlight replacement including cable Kit forKawai K5000 We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionThis Display fits inNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Yamaha USB Socket Typ B PCBJalco used by: Yamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 pcs. Yamaha USB Socket Typ A PCBJalco YKF45-0021used by: Yamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 piece Electrolytical Capacitor 68uF/400V for Switching Power SupplyManufakturer: Nichicon Here i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Recapping set forE-Mu Proteus 1E-Mu Proteus 2E-Mu ProcussionThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.This Recapping Set contains all necessary Capacitors for Switching Power Supply and Mainboard. Warning PSU Recapping:Risk of electric shock:Switching power supplys store high voltage and high energy for a very long period of time.When working with these spare parts offered here, you are working directly in a 230VAC circuit.Observe polarity. Incorrect installation will cause explosion and fire.For experts only: Be aware of dangers of electric current  

Replacement Keys, weighted for Korg SK4 KeyboardColor: pure whiteThe Korg SK4 Keyboard is a touch-sensitive keyboard with weighted Keys.The weighted keys have a length of 15.5 cm with a width of 2.24 cm. The depth of the key is 3.5 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is from the front 10 cm. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping.